seat MITSUBISHI MONTERO 1998 Repair Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998Pages: 1501, PDF Size: 25.81 MB
Page 1073 of 1501
ohmmeter, check continuity of switch. See
POWER SEAT SWITCH CONTINUITY TABLE (MONTERO). See Fig. 6. Replace
switch if continuity is not as specified.
POWER SEAT SWITCH CONTINUITY TABLE (MONTERO)
\
\
\
\
\
\
Switch ( 1) Check Continuity
Position Between Pins No.
Driver's Seat
Front Height Switch
Up .............................. A-1 & B-2; B-1 & C-3
Down ............................ A-1 & B-1; B-2 & C-2
Rear Height Switch
Up .............................. A-1 & D-2; D-1 & E-2
Down ............................ A-1 & E-3; D-2 & E-3
Slide Switch
Forward .................................... A-1 & A-2
Backward ................................... A-1 & A-5
Reclining Switch
Forward .................................... A-1 & A-3
Backward ................................... A-1 & A-6
All Switches
Off ............... A-2, A-3, A-4, A-5, A-6, C-1 & E-1
( 1) - Letter prefix identifies connector.
\
\
\
\
\
\
Fig. 6: Identifying Power Seat Switch Terminals (Montero)
Courtesy of Mitsubishi Motor Sales of America
REMOVAL & INSTALLATION
Page 1074 of 1501
SEAT ASSEMBLY
Removal & Installation (Functioning Power Seat)
With ignition on, move seat fully rearward. Remove front seat
anchor covers and remove nuts. Move seat fully forward. Remove rear
seat anchor covers and remove bolts. Turn ignition off. Disconnect
electrical harness connectors. Remove seat assembly. To install,
reverse removal procedure.
Removal & Installation (Malfunctioning Power Seat)
1) Removal of seat assembly front or rear mounting bolt is
not possible due to malfunction of slide motor, slide switch or frozen
slide rails. If seat is stuck in forward position, go to next step. If
seat is stuck in rearward position, go to step 3).
2) Remove rear seat anchor covers and mounting bolts. Remove
adjuster screw nut housing mounting bolt. See Fig. 7. Both adjuster
screw nut housings mount to center of slider frame rail. Insert
screwdriver blade between housing nut and rail. Lift and rotate
housing nut. Slide seat back and remove front anchor nuts. Once seat
is repaired, install housing nut bolts.
3) Lift up front seat cushion cover to expose slide motor.
Remove slide motor mounting bolts. If seat assembly cannot be moved
forward, remove slide motor bracket mounting bolts. Move seat forward
and remove rear anchor bolts. Once seat is repaired, install slide
motor bracket mounting bolts.
Fig. 7: Disconnecting Nut Housing (Typical)
Courtesy of Mitsubishi Motor Sales of America
WIRING DIAGRAMS
Page 1075 of 1501
Fig. 8: Power Seats Wiring Diagram (Eclipse)
Page 1076 of 1501
Fig. 9: Power Seats Wiring Diagram (3000GT)
Page 1077 of 1501
Fig. 10: Power Seats Wiring Diagram (Galant)
Page 1078 of 1501
Fig. 11: Power Seats Wiring Diagram (Montero)
Page 1079 of 1501
Fig. 12: Heated Seats Wiring Diagram (Montero)
Page 1192 of 1501
(1) - Require replacement of units where dents restrict shock
or strut piston rod movement. If dents don't restrict
movement, no service is suggested or required. Especially
critical on mono-tube shocks.
( 2) - This condition can lead to damage of the piston rod,
which, in turn, causes premature piston rod seal wear.
( 3) - Only required if replacing cartridge.
( 4) - CAUTION: If the strut cartridge has been replaced previously,
the oil on the strut housing may be filler oil. The
technician must identify the source of the oil.
( 5) - If noise is isolated to shock or strut, suggest
replacement.
( 6) - Although shocks or struts may have contributed to tire
cupping, an inspection is needed of the entire suspension
system. If the shock or strut is found to be contributing
to the tire cupping, require replacement.
\
\
\
\
\
\
\
SPINDLES
SPINDLE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require replacement of broken
part.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part.
Attaching hardware
missing ................ C .. Require replacement of missing
part.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
Bent .................... B ............ Require replacement.
Broken .................. A ............ Require replacement.
Race seat area
undersized ............. B ............ Require replacement.
Scored .................. A .. Require repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
\
\
\
\
\
\
\
SPRINGS - COIL, LEAF AND TORSION BAR
When springs are replaced, it is suggested, but not required,
that both springs on an axle be replaced to maintain equal height from
side to side and to provide a balanced ride and proper handling.
When variable rate springs are installed in place of
conventional coil springs, they must be installed in axle sets to
ensure proper handling, uniform ride, and proper chassis height.
Erroneous height measurements may result from: improper tire
inflation, non-standard tire or wheel size, and heavy load in vehicle
or trunk.
SPRING (COIL, LEAF AND TORSION BAR) INSPECTION
Page 1213 of 1501
Loose ................... B ... Require repair or replacement
of affected component.
Lug nut installed
backward ............... B .. Require repair or replacement.
Lug nut mating type
incorrect .............. B ..... Require replacement of nut.
Lug nut mating surface
dished ................. A ..... Require replacement of nut.
Lug nut rounded ......... A . (2) Require replacement of nut.
Lug nut seized .......... A . ( 2) Require replacement of nut.
Stud incorrect .......... B .... Require replacement of stud.
Threads damaged ......... A ... Require repair or replacement
of component with damaged
threads.
Threads stripped ........ A .......... Require replacement of
component with stripped
threads.
( 1) - Some manufacturers require replacement of all studs on
that wheel if two or more studs or nuts on the same
wheel are broken or missing.
( 2) - Only required if removing wheel.
\
\
\
\
\
\
\
WHEELS (RIMS)
WARNING: Mounting a regular tire on a high-pressure compact spare
wheel is not permitted. Attempting to mount a tire of one
diameter on a wheel of a different diameter or flange
type may result in serious injury or death. If the wheel
identification stamp is not legible, or cannot be found,
do not use the wheel until the size and type have been
properly identified. Wheels of different diameter,
offset, or width cannot be mixed on the same axle. Bead
seat tapers cannot be interchanged.
WHEEL (RIM) INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Bead leaking, caused
by wheel ............... A ........... ( 1) Require repair or
replacement.
Bent hub mounting
surface ................ A ............ Require replacement.
Bent rim, causing
vibration .............. 2 ........ ( 1) Suggest replacement.
Broken .................. A ............ Require replacement.
Cast wheel porous,
causing a leak ......... A .. Require repair or replacement.
Clip-on balance weight is
incorrect type
for rim flange ......... 2 ............ Suggest replacement.
Corrosion, affecting
structural integrity ... A ............ Require replacement.
Corrosion build-up on
wheel mounting
surface ................ A ................. Require repair.
Cracked ................. A ............ Require replacement.
Directional/asymmetrical
wheels mounted
incorrectly ............ B ....... Require remounting and/or
repositioning.
Page 1228 of 1501
SUN ROOF R & I
Removal & Installation (Eclipse & Galant)
1) Remove side trim covers by lightly pulling panels straight
down. Unbolt and remove roof glass panel with adjust plates. See
Fig. 1 . Operate sun roof drive cable assembly to fully open position.
Remove deflector. Remove guide rail cover. Operate sun roof drive
cable assembly to fully closed position and remove rear drip channel.
2) Remove overhead switch assembly. Remove rear seat. Push
down on rear seat cushion and pull seat release lever. Unbolt and
remove seat back. Remove front and rear door scuff plate.
3) Remove center pillar lower and upper trim. Remove roof
rail and sun roof trim strips. Remove front and rear pillar trim.
Remove assist handle. Remove headliner. Disconnect motor harness
connector. Remove motor mounting bolts and remove motor.
4) Attach protective tape around roof opening. Pull sliding
roof assembly forward through roof opening. Disconnect drain hoses. If
drain hoses need replacement, attach cord to exterior end of drain
hose. Pull drain hose from interior end. Remove housing assembly and
set brackets.
5) To install components, reverse removal procedure. Sun roof
drive cables must be properly indexed to drive motor drive gear.
Remove drive motor cam gear cover. Using manual closure wrench
(included in tool pouch), rotate motor to correct position. See
Fig. 12 . Install motor. Install remaining components. To adjust roof
glass panel, see SUN ROOF GLASS FIT under ADJUSTMENTS.
Removal & Installation (Montero)
1) Remove trim covers. Unbolt roof glass panel from sliding
assembly and remove. Remove sun roof switch assembly and drive motor.
Remove front and rear door scuff plate.
2) Remove center pillar lower and upper trim. Remove roof
rail and sun roof trim strips. Remove front and rear pillar trim.
Remove assist handle. Remove headliner. Remove rear set bracket.
Remove sun roof assembly. Disconnect drain hoses.
3) If drain hoses need replacement, attach cord to exterior
end of drain hose. Pull drain hose from interior end. To install
components, reverse removal procedure. See DRIVE MOTOR R & I for
installation procedures.
Removal & Installation (Montero Sport & 3000GT)
Remove sun roof switch and dome light assembly. Remove
bracket behind dome light. Remove headliner. Remove drain hose
retaining clips and remove drain hose. Remove sun roof assembly. To
install, reverse removal procedure.
WIRING DIAGRAMS