seat MITSUBISHI MONTERO 1998 Workshop Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998Pages: 1501, PDF Size: 25.81 MB
Page 996 of 1501
DISTRIBUTOR
NOTE: Eclipse, Mirage 1.8L, Montero, Montero Sport 3.0L and 3000GT
DOHC use Distributorless Ignition System (DIS). All other
models use distributor type ignition systems with
non-serviceable distributors on which only the rotor and
distributor cap can be changed.
FUEL SYSTEM
* PLEASE READ THIS FIRST *
WARNING: Always relieve fuel pressure before disconnecting any fuel
injection-related component. DO NOT allow fuel to contact
engine or electrical components.
FUEL SYSTEM PRESSURE RELEASE
Relieving Fuel Pressure
1) On Diamante, disconnect fuel pump harness connector at
fuel tank from underneath vehicle. On Montero and Montero Sport,
remove cargo compartment carpet, remove access plate and disconnect
fuel pump harness connector. On all other models, remove rear seat
cushion and remove access plate (if required) to disconnect fuel pump
harness connector.
2) On all models, start engine. Let engine run until it
stops. Turn ignition off. Disconnect negative battery cable. Connect
fuel pump harness connector. Reinstall rear seat (if necessary.)
FUEL PUMP
Removal & Installation (Diamante, Eclipse, Galant & Montero)
1) Fuel pump assembly is located inside fuel tank. Release
fuel pressure. See FUEL SYSTEM PRESSURE RELEASE . Remove access panel
under seat, in trunk or in rear cargo area. Disconnect electrical
connectors and fuel hoses at fuel tank.
2) Remove fuel filler hose from fuel tank. Remove fuel pump
assembly. To install, reverse removal procedure. Tighten nuts to
specification. See TORQUE SPECIFICATIONS .
Removal & Installation (Mirage, Montero Sport & 3000GT)
1) Fuel pump assembly is located inside fuel tank. Release
fuel pressure. See FUEL SYSTEM PRESSURE RELEASE . Raise vehicle on
hoist. Drain fuel into suitable container. Disconnect electrical
connectors and breather/fuel hoses at fuel tank.
2) Remove fuel filler hose from fuel tank. Support fuel tank
with transmission jack. Remove nuts securing fuel tank. Remove fuel
tank from vehicle. Remove fuel pump assembly. To install, reverse
removal procedure. Tighten nuts to specification. See
TORQUE SPECIFICATIONS .
FUEL RAILS & INJECTORS
WARNING: Use a rag to cover fuel hose connection before disconnecting
high pressure fuel hose at fuel rail. Some residual fuel
pressure may still be in system.
CAUTION: DO NOT drop injectors while removing or installing fuel rail.
Removal (Diamante, Montero Sport 2.4L & 3000GT)
Page 1006 of 1501
PASSIVE RESTRAINT SYSTEM INSPECTION
1998 Mitsubishi Montero
GENERAL INFORMATION
Passive Restraint System Inspection - Asian
* PLEASE READ THIS FIRST *
Follow all manufacturers servicing precautions when working
with air bag systems. See SERVICE PRECAUTIONS in the appropriate AIR
BAG RESTRAINT SYSTEM article in the ACCESSORIES/SAFETY EQUIPMENT
section.
INTRODUCTION
When a vehicle equipped with passive restraint system has
been involved in a collision, certain systems and components must be
inspected and or replaced regardless of whether or not the air bag has
deployed. Follow the manufacturer's guidelines provided in this
article.
ACURA (1988-98)
AIR BAG APPLICATION
AIR BAG APPLICATION TABLE - ACURA (1988-98) \
\
\
\
\
\
Model Year (1) Location
Integra .............. 1994-98 ..................... D/P
Legend ............... 1991-95 ..................... D/P
1988-90 ...................... DS
NSX .................. 1993-98 ..................... D/P
1991-92 ...................... DS
Vigor ................ 1993-94 ..................... D/P
1992 ........................ DS
2.2CL ................. 1997 ....................... D/P
2.3CL ................. 1998 ....................... D/P
2.5TL ................ 1995-98 ..................... D/P
3.0CL ................ 1997-98 ..................... D/P
3.2TL ................ 1996-98 ..................... D/P
3.5RL ................ 1996-98 ..................... D/P
SLX .................. 1996-98 ..................... D/P
( 1) - Location Definitions: D/P = Driver's & Passenger's
Side, DS = Driver's Side Only, SI = Side Impact.
\
\
\
\
\
\
INSPECTION PROCEDURES
INSPECTION PROCEDURES TABLE - ACURA (1988-98 EXCEPT SLX) \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Seat Belt Tensioners (If Equipped)
* SRS Control Unit
\
\
\b \
\
\
\
\
Inspect & If
* Cable Reel
Damaged, Replace
* Dash or Impact Sensors (If Equipped)
Component
* Seat Belts
Page 1007 of 1501
(Even If Air * SRS Control Unit
Bag Did Not
* Wiring Harness
Deploy)
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
must be replaced.
* DO NOT attempt SRS wiring repairs. If SRS
wiring or harness connectors are faulty,
replace faulty wiring harness.
* After vehicle is repaired, ensure AIR BAG
warning light is functioning properly.
\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - ACURA (1996-98 SLX) \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Sensing & Diagnostic Module (SDM)
\
\
\b \
\
\
\
\
Inspect & If
* Instrument Panel Braces
Damaged, Replace
* Instrument Panel Steering Column
Component Reinforcement Plate
(Even If Air
* Seat Belts & Mounting Points
Bag Did Not
* Knee Bolsters & Mounting Points
Deploy)
* Steering Column
* SRS Coil Assembly
* Wiring Harnesses
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
must be replaced.
* DO NOT attempt wiring harness repairs.
Replace harness.
\
\
\
\
\
\
\
\f
HONDA (1991-98)
AIR BAG APPLICATION
AIR BAG APPLICATION TABLE - HONDA (1991-98) \
\
\
\
\
\
Model Year (1) Location
Accord ............... 1993-98 ..................... D/P
1991-92 ...................... DS
Civic ................ 1994-98 ..................... D/P
1992-93 ...................... DS
Civic del Sol ........ 1994-97 ..................... D/P
1993 ........................ DS
CR-V ................. 1997-98 ..................... D/P
Odyssey .............. 1995-98 ..................... D/P
Prelude .............. 1994-98 ..................... D/P
SI 4WS ............. 1992-93 ..................... D/P
Except SI 4WS ...... 1992-93 ...................... DS
Passport ........... 1995 1/2-98 ................... D/P
( 1) - Location Definitions: D/P = Driver's & Passenger's
Side, DS = Driver's Side Only, SI = Side Impact.
\
\
\
\
\
\
INSPECTION PROCEDURES
Page 1008 of 1501
![MITSUBISHI MONTERO 1998 Workshop Manual INSPECTION PROCEDURES TABLE - HONDA (1991-98 EXCEPT PASSPORT) \
\
\
\
\
\
\](/img/19/57333/w960_57333-1007.png "MITSUBISHI MONTERO 1998 Workshop Manual INSPECTION PROCEDURES TABLE - HONDA (1991-98 EXCEPT PASSPORT) \
\
\
\
\
\
\")
INSPECTION PROCEDURES TABLE - HONDA (1991-98 EXCEPT PASSPORT) \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Seat Belt Tensioners (If Equipped)
* SRS Control Unit
\
\
\b \
\
\
\
\
Inspect & If
* Cable Reel
Damaged, Replace
* Dash Sensors (1991-94)
Component
* Seat Belts
(Even If Air
* SRS Control Unit
Bag Did Not
* Wiring Harness
Deploy)
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
must be replaced.
* DO NOT attempt SRS wiring repairs. If SRS
wiring or harness connectors are faulty,
replace faulty wiring harness.
* After vehicle is repaired, ensure AIR BAG
warning light is functioning properly.
\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - HONDA (1995 1/2-98 PASSPORT) \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Sensing & Diagnostic Module (SDM)
\
\
\b \
\
\
\
\
Inspect & If
* Instrument Panel Braces
Damaged, Replace
* Instrument Panel Steering Column
Component Reinforcement Plate
(Even If Air
* Seat Belts & Mounting Points
Bag Did Not
* Knee Bolsters & Mounting Points
Deploy)
* Steering Column
* SRS Coil Assembly
* Wiring Harnesses
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
must be replaced.
* DO NOT attempt wiring harness repairs.
Replace harness.
\
\
\
\
\
\
\
\f
HYUNDAI (1994-98)
AIR BAG APPLICATION
AIR BAG APPLICATION TABLE - HYUNDAI (1994-98) \
\
\
\
\
\
Model Year (1) Location
Accent ............... 1995-98 ..................... D/P
Elantra .............. 1996-98 ..................... D/P
1994-95 ...................... DS
Sonata ............... 1995-98 ..................... D/P
Tiburon .............. 1997-98 ..................... D/P
( 1) - Location Definitions: D/P = Driver's & Passenger's
Side, DS = Driver's Side Only, SI = Side Impact.
Page 1009 of 1501
![MITSUBISHI MONTERO 1998 Workshop Manual \
\
\
\
\
\
INSPECTION PROCEDURES
INSPECTION PROCEDURES TABLE - HYUNDAI](/img/19/57333/w960_57333-1008.png "MITSUBISHI MONTERO 1998 Workshop Manual \
\
\
\
\
\
INSPECTION PROCEDURES
INSPECTION PROCEDURES TABLE - HYUNDAI")
\
\
\
\
\
\
INSPECTION PROCEDURES
INSPECTION PROCEDURES TABLE - HYUNDAI (1994-98) \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Control Module
* Steering Column Clockspring
\
\
\b \
\
\
\
\
Inspect & If
* Any Seat Belt In Use At Time Of Collision
Damaged, Replace
* Steering Column
Component
* Steering Wheel
(Even If Air
* Wiring Harness
Bag Did Not
Deploy)
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
must be replaced.
* DO NOT attempt SRS wiring repairs. If SRS
wiring or harness connectors are faulty,
replace faulty wiring harness.
\
\
\
\
\
\
\
\f
INFINITI (1990-98)
AIR BAG APPLICATION
AIR BAG APPLICATION TABLE - INFINITI (1990-98) \
\
\
\
\
\
\
Model Year (1) Location Inspection Table
G20 ......... 1993-96 ........... D/P ............... INFINITI-2
I30 ........... 1998 .......... D/P, SI ............. INFINITI-1
1997 ............ D/P ............... INFINITI-1
1996 ............ D/P ............... INFINITI-2
J30 ........... 1997 ............ D/P ............... INFINITI-1
1994-96 ........... D/P ............... INFINITI-2
1993 ............ D/P ............... INFINITI-3
M30 ......... 1990-92 ............ DS ............... INFINITI-3
Q45 ........... 1998 .......... D/P, SI ............. INFINITI-1
1997 ............ D/P ............... INFINITI-1
1994-96 ........... D/P ............... INFINITI-2
1990-93 ............ DS ............... INFINITI-3
QX4 ......... 1997-98 ........... D/P ............... INFINITI-1
( 1) - Location Definitions: D/P = Driver's & Passenger's Side,
DS = Driver's Side Only, SI = Side Impact.
\
\
\
\
\
\
\
INSPECTION PROCEDURES
INSPECTION PROCEDURES TABLE - INFINITI-1 \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Control Unit, Diagnosis
* Satellite Sensor ( 1)
* Seat Belt Pretensioners ( 2)
Page 1010 of 1501
![MITSUBISHI MONTERO 1998 Workshop Manual * Side Air Bag Module ( 1)
\
\
\b \
\
\
\](/img/19/57333/w960_57333-1009.png "MITSUBISHI MONTERO 1998 Workshop Manual * Side Air Bag Module ( 1)
\
\
\b \
\
\
\")
* Side Air Bag Module ( 1)
\
\
\b \
\
\
\
\
Inspect & If
* Center Pillar Inner ( 1)
Damaged, Replace
* Instrument Panel
Component
* Seat ( 1)
(Even If Air
* Seat Belt Pretensioners ( 2)
Bag Did Not
* Spiral Cable
Deploy)
* Steering Wheel
* Wiring Harnesses
\
\
\b \
\
\
\
\
Comments
* Inspect all SRS components for dents,
deformities or rust.
* After repairs are completed, check AIR BAG
warning light to ensure system is functioning
properly.
\
\
\
\
\
\
\
(
1) - On side of impact.
(
2) - Except I30 and QX4.
\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - INFINITI-2 \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Control Unit, Diagnosis
* Instrument Panel
* Seat Belt Pretensioners ( 1)
\
\
\b \
\
\
\
\
Inspect & If
* All Sensors ( 2)
Damaged, Replace
* Spiral Cable
Component
* Steering Wheel
(Even If Air
* Wiring Harnesses
Bag Did Not
Deploy)
\
\
\b \
\
\
\
\
Comments
* Inspect all SRS components for dents,
deformities or rust.
* After repairs are completed, check AIR BAG
warning light to ensure system is functioning
properly.
\
\
\
\
\
\
\
(
1) - Except I30.
(
2) - Except 1996 I30, 1995-96 J30 and 1995-96 Q45.
\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - INFINITI-3 \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Control Unit, Diagnosis
* Sensors In Affected Collision Area
\
\
\b \
\
\
\
\
Inspect & If
* All Sensors
Damaged, Replace
* Spiral Cable
Component
* Steering Wheel
(Even If Air
* Wiring Harnesses
Bag Did Not
Deploy)
\
\
\b \
\
\
\
\
Comments
* Inspect all SRS components for dents,
deformities or rust.
Page 1011 of 1501
* After repairs are completed, check AIR BAG
warning light to ensure system is functioning
properly.
\
\
\
\
\
\
\
\f
ISUZU (1990-98)
AIR BAG APPLICATION
AIR BAG APPLICATION TABLE - ISUZU (1990-98) \
\
\
\
\
\
\
Model Year (1) Location Inspection Table
Hombre ....... 1996-97 ........... DS .................. ISUZU-1
Impulse ...... 1990-92 ........... DS .................. ISUZU-5
Oasis ........ 1996-98 .......... D/P .................. ISUZU-2
Rodeo ........ 1996-98 .......... D/P .................. ISUZU-3
1995 1/2 ......... D/P .................. ISUZU-3
Stylus ....... 1991-93 ........... DS .................. ISUZU-5
Trooper ...... 1996-98 .......... D/P .................. ISUZU-3
1995 ............ D/P .................. ISUZU-4
( 1) - Location Definitions: D/P = Driver's & Passenger's Side,
DS = Driver's Side Only, SI = Side Impact.
\
\
\
\
\
\
\
INSPECTION PROCEDURES
INSPECTION PROCEDURES TABLE - ISUZU-1 \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Sensors In Area Of Accident Damage
\
\
\b \
\
\
\
\
Inspect & If
* Instrument Panel Braces
Damaged, Replace
* Instrument Panel Steering Column
Component Reinforcement Plate
(Even If Air
* Seat Belts & Mounting Points
Bag Did Not
* Knee Bolster
Deploy)
* Sensors In Area Of Accident Damage
* SRS Coil Assembly
\
\
\b \
\
\
\
\
Comments
* Any sensor which the Diagnostic Energy
Reserve Module (DERM) indicates as bad must
be replaced.
* If any components are damaged or bent, they
must be replaced.
* SRS wiring can be repaired following
manufacturer's instructions.
\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - ISUZU-2 \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Seat Belt Tensioners (If Equipped)
* SRS Control Unit
\
\
\b \
\
\
\
\
Inspect & If
* Cable Reel
Damaged, Replace
* Dash Sensors (1991-94)
Page 1012 of 1501
Component * Seat Belts
(Even If Air
* SRS Control Unit
Bag Did Not
* Wiring Harness
Deploy)
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
must be replaced.
* DO NOT attempt SRS wiring repairs. If SRS
wiring or harness connectors are faulty,
replace faulty wiring harness.
* After vehicle is repaired, ensure AIR BAG
warning light is functioning properly.
\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - ISUZU-3 \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Sensing & Diagnostic Module (SDM)
\
\
\b \
\
\
\
\
Inspect & If
* Instrument Panel Braces
Damaged, Replace
* Instrument Panel Steering Column
Component Reinforcement Plate
(Even If Air
* Seat Belts & Mounting Points
Bag Did Not
* Knee Bolsters & Mounting Points
Deploy)
* Steering Column
* SRS Coil Assembly
* Wiring Harnesses
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
must be replaced.
* DO NOT attempt wiring harness repairs.
Replace harness.
\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - ISUZU-4 \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* All Sensors
\
\
\b \
\
\
\
\
Inspect & If
* SRS Coil Assembly
Damaged, Replace
* Instrument Panel Steering Column
Component Reinforcement Panel
(Even If Air
* Instrument Panel Braces
Bag Did Not
* Knee Bolsters
Deploy)
* Seat Belts Mounting Points
* Sensors In Area of Accident Damage
* Steering Column
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
must be replaced.
* DO NOT attempt wiring harness repairs.
Replace harness.
\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - ISUZU-5 \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module
Page 1014 of 1501
Model Year (1) Location Inspection Table
ES250 ....... 1990-91 ........... DS ................... LEXUS-6
ES300 ......... 1998 .......... D/P, SI ................ LEXUS-3
1997 ............ D/P .................. LEXUS-1
1994-96 ........... D/P .................. LEXUS-4
1992-93 ........... DS ................... LEXUS-5
GS300 ......... 1998 .......... D/P, SI ................ LEXUS-3
1993-97 . .......... D/P .................. LEXUS-4
GS400 ......... 1998 .......... D/P, SI ................ LEXUS-3
LS400 ....... 1997-98 ......... D/P, SI ................ LEXUS-3
1995-96 ........... D/P .................. LEXUS-1
1993-94 ........... D/P .................. LEXUS-4
1990-92 ........... DS ................... LEXUS-6
LX450 ....... 1996-97 ........... D/P .................. LEXUS-1
LX470 ......... 1998 ............ D/P .................. LEXUS-2
SC300 ....... 1996-98 ........... D/P .................. LEXUS-1
1993-95 ........... D/P .................. LEXUS-4
1992 ............. DS ................... LEXUS-5
SC400 ....... 1996-98 ........... D/P .................. LEXUS-1
1993-95 ........... D/P .................. LEXUS-4
1992 ............. DS ................... LEXUS-5
( 1) - Location Definitions: D/P = Driver's & Passenger's Side,
DS = Driver's Side Only, SI = Side Impact.
\
\
\
\
\
\
\
INSPECTION PROCEDURES
INSPECTION PROCEDURES TABLE - LEXUS-1 \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Air Bag Sensor Assembly
* Front Seat Belt Pretensioners ( 1)
\
\
\b \
\
\
\
\
Inspect & If
* Glove Compartment Door ( 2)
Damaged, Replace
* Instrument Panel
Component
* Instrument Panel Reinforcement
(Even If Air
* Spiral Cable
Bag Did Not
* Steering Wheel
Deploy)
* Wiring Harness & Connectors
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
must be replaced.
\
\
\
\
\
\
\
(
1) - 1995 LS400 only.
(
2) - 1997 ES300, 1996 LS400 and 1996-97 LX450 only.
\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - LEXUS-2 \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Air Bag Sensor Assembly
* Front Air Bag Sensors
* Seat Belt Pretensioner
\
\
\b \
\
\
\
\
Inspect & If
* Instrument Panel
Damaged, Replace
* Instrument Panel Reinforcement
Component
* Seat Belt Pretensioner
Page 1015 of 1501
(Even If Air * Spiral Cable Steering Wheel
Bag Did Not
* Wiring Harness & Connectors
Deploy)
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
must be replaced.
* DO NOT attempt wiring harness repairs.
Replace entire wiring harness.
\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - LEXUS-3 \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Air Bag Sensor Assembly
* Seat Belt Pretensioner ( 1)
* Side Air Bag Modules
* Side Air Bag Sensor Assembly
\
\
\b \
\
\
\
\
Inspect & If
* Glove Compartment Door ( 2)
Damaged, Replace
* Instrument Panel Instrument Panel
Component Reinforcement
(Even If Air
* Seat Belt Pretensioner ( 1)
Bag Did Not
* Spiral Cable
Deploy)
* Steering Wheel
* Wiring Harness & Connectors
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
must be replaced.
* DO NOT attempt wiring harness repairs.
Replace entire wiring harness.
\
\
\
\
\
\
\
(
1) - Except 1997 LS400.
(
2) - 1997 LS400 only.
\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - LEXUS-4 \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Center Air Bag Sensor Assembly
* Front Air Bag Sensors
* Front Seat Belt Tensioners ( 1)
\
\
\b \
\
\
\
\
Inspect & If
* Glove Compartment Door ( 2)
Damaged, Replace
* Instrument Panel
Component
* Instrument Panel Reinforcement
(Even If Air
* Spiral Cable
Bag Did Not
* Steering Wheel
Deploy)
* Wiring Harness & Connectors
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
must be replaced.
* Wiring for Front Air Bag Sensors can be
repaired following manufacturer's
instructions.
\
\
\
\
\
\
\
(
1) - 1993-95 GS300 and 1993-94 LS400.
(
2) - Except 1994-95 SC300 and SC400.
\
\
\
\
\
\
\
\f