steering system MITSUBISHI MONTERO 1998 Manual PDF
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998Pages: 1501, PDF Size: 25.81 MB
Page 1023 of 1501
![MITSUBISHI MONTERO 1998 Manual PDF \
\
\b \
\
\
\
\
Comments
* DO NOT attempt SRS w](/img/19/57333/w960_57333-1022.png "MITSUBISHI MONTERO 1998 Manual PDF \
\
\b \
\
\
\
\
Comments
* DO NOT attempt SRS w")
\
\
\b \
\
\
\
\
Comments
* DO NOT attempt SRS wiring repairs.
* If any components are damaged or bent, they
must be replaced.
\
\
\
\
\
\
\
(
1) - If Equipped.
(
2) - 1998 Legacy, on side of deployment.
\
\
\
\
\
\
\
\f
SUZUKI (1995-98)
AIR BAG APPLICATION
AIR BAG APPLICATION TABLE - SUZUKI (1995-98) \
\
\
\
\
\
Model Year (1) Location
Esteem .............. 1995-98 ...................... D/P
Sidekick ............ 1996-98 ...................... D/P
Swift ............... 1995-98 ...................... D/P
X90 ................. 1996-98 ...................... D/P
( 1) - Location Definitions: D/P = Driver's & Passenger's
Side, DS = Driver's Side Only, SI = Side Impact.
\
\
\
\
\
\
INSPECTION PROCEDURES
INSPECTION PROCEDURES TABLE - SUZUKI (1995-98) \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air BagModule(s)
Deployment
* Sensing & Diagnostic Module (SDM)
\
\
\b \
\
\
\
\
Inspect & If
* Air Bag Warning Light
Damaged, Replace
* Combination Switch Assembly
Component
* Contact Coil
(Even If Air
* Forward Discriminating Sensor ( 1)
Bag Did Not
* Instrument Panel Reinforcement
Deploy)
* Knee Bolsters
* Seat Belts & Mounting Points
* SDM Bracket
* Steering Column Bracket
* Steering Column & Shaft Joints
* Steering Wheel
* Wiring Harness
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
must be replaced.
\
\
\
\
\
\
\
(
1) - Swift Only
\
\
\
\
\
\
\
\f
TOYOTA (1990-98)
Page 1025 of 1501
![MITSUBISHI MONTERO 1998 Manual PDF \
\
\b \
\
\
\
\
Inspect & If
* Instrument Panel](/img/19/57333/w960_57333-1024.png "MITSUBISHI MONTERO 1998 Manual PDF \
\
\b \
\
\
\
\
Inspect & If
* Instrument Panel")
\
\
\b \
\
\
\
\
Inspect & If
* Instrument Panel
Damaged, Replace
* Instrument Panel Reinforcement
Component
* Seatback Assembly ( 2)
(Even If Air
* Seat Belt Pretensioner ( 2)
Bag Did Not
* Spiral Cable
Deploy)
* Steering Wheel
* Wiring Harness & Connectors
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
must be replaced.
* DO NOT attempt wiring harness repairs.
Replace entire wiring harness.
\
\
\
\
\
\
\
(
1) - Corolla and Sienna only. Replace both sensors.
(
2) - On side of impact.
(
3) - Avalon only.
\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - TOYOTA-2 \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Air Bag Sensor Assembly
* Front Air Bag Sensors
* Seat Belt Pretensioner ( 1)
\
\
\b \
\
\
\
\
Inspect & If
* Instrument Panel
Damaged, Replace
* Instrument Panel Reinforcement
Component
* Seat Belt Pretensioner ( 1)
(Even If Air
* Spiral Cable
Bag Did Not
* Steering Wheel
Deploy)
* Wiring Harness & Connectors
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
must be replaced.
* DO NOT attempt wiring harness repairs.
Replace entire wiring harness.
\
\
\
\
\
\
\
(
1) - Land Cruiser and Tercel only.
\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - TOYOTA-3 \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Air Bag Sensor Assembly
* Front Air Bag Sensor ( 1)
* Instrument Panel ( 2)
* Instrument Panel Reinforcement ( 2)
* Spiral Cable ( 3)
* Steering Wheel ( 3)
\
\
\b \
\
\
\
\
Inspect & If
* Spiral Cable ( 4)
Damaged, Replace
* Steering Wheel ( 4)
Component
* Wiring Harness & Connectors
(Even If Air
Bag Did Not
Deploy)
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
Page 1026 of 1501
![MITSUBISHI MONTERO 1998 Manual PDF must be replaced.
\
\
\
\
\
\](/img/19/57333/w960_57333-1025.png "MITSUBISHI MONTERO 1998 Manual PDF must be replaced.
\
\
\
\
\
\")
must be replaced.
\
\
\
\
\
\
\
(
1) - 1998 RAV4 only.
(
2) - Except 1996-97 Tacoma and 1998 Supra.
(
3) - Except 1998 Tacoma.
(
4) - 1998 Tacoma.
\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - TOYOTA-4 \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Air Bag Sensor Assembly
* Glove Compartment Door
* Instrument Panel
* Instrument Panel Reinforcement
* Spiral Cable
* Steering Wheel
\
\
\b \
\
\
\
\
Inspect & If
* Wiring Harness & Connectors
Damaged, Replace
Component
(Even If Air
Bag Did Not
Deploy)
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent,
they must be replaced.
\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - TOYOTA-5 \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Center Air Bag Sensor Assembly
* Front Air Bag Sensors
* Instrument Panel
* Instrument Panel Reinforcement
* Spiral Cable
* Steering Wheel
\
\
\b \
\
\
\
\
Inspect & If
* Wiring Harness & Connectors
Damaged, Replace
Component
(Even If Air
Bag Did Not
Deploy)
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
must be replaced.
* Wiring for Front Air Bag Sensors can be
repaired following manufacturer's
instructions.
\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - TOYOTA-6 \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Center Air Bag Sensor Assembly
Page 1027 of 1501
* Front Air Bag Sensors
* Glove Compartment
* Glove Compartment Door
* Instrument Panel
* Instrument Panel Reinforcement
* Spiral Cable
* Steering Wheel
\
\
\b \
\
\
\
\
Inspect & If
* Wiring Harness & Connectors
Damaged, Replace
Component
(Even If Air
Bag Did Not
Deploy)
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
must be replaced.
* Wiring for Front Air Bag Sensors can be
repaired following manufacturer's
instructions.
\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - TOYOTA-7 \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Center Air Bag Sensor Assembly
* Center Console Bracket Support
* Front Air Bag Sensors
* Instrument Panel
* Spiral Cable
* Steering Wheel
\
\
\b \
\
\
\
\
Inspect & If
* Wiring Harness & Connectors
Damaged, Replace
Component
(Even If Air
Bag Did Not
Deploy)
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
must be replaced.
* Wiring for Front Air Bag Sensors can be
repaired following manufacturer's
instructions.
\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - TOYOTA-8 \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Air Bag Sensor Assembly
* Center Console Bracket Support
* Instrument Panel Spiral Cable
* Steering Wheel
\
\
\b \
\
\
\
\
Inspect & If
* Wiring Harness & Connectors
Damaged, Replace
Component
(Even If Air
Bag Did Not
Page 1028 of 1501
![MITSUBISHI MONTERO 1998 Manual PDF Deploy)
\
\
\b \
\
\
\](/img/19/57333/w960_57333-1027.png "MITSUBISHI MONTERO 1998 Manual PDF Deploy)
\
\
\b \
\
\
\")
Deploy)
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
must be replaced.
\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - TOYOTA-9 \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Center Air Bag Sensor Assembly
* Front Air Bag Sensors
* Spiral Cable
* Steering Wheel
\
\
\b \
\
\
\
\
Inspect & If
* Wiring Harness & Connectors
Damaged, Replace
Component
(Even If Air
Bag Did Not
Deploy)
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
must be replaced.
* Wiring for Front Air Bag Sensors can be
repaired following manufacturer's
instructions.
\
\
\
\
\
\
\
\f
INSPECTION PROCEDURES TABLE - TOYOTA-10 \
\
\
\
\
\
\
Action Component or System
\
\
\b \
\
\
\
\
Replace After
* Air Bag Module(s)
Deployment
* Front Air Bag Sensors
* Spiral Cable
* Steering Wheel
\
\
\b \
\
\
\
\
Inspect & If
* Center Air Bag Sensor Assembly
Damaged, Replace
* Wiring Harness & Connectors
Component
(Even If Air
Bag Did Not
Deploy)
\
\
\b \
\
\
\
\
Comments
* If any components are damaged or bent, they
must be replaced.
* Wiring for Front Air Bag Sensors can be
repaired following manufacturer's
instructions.
\
\
\
\
\
\
\
\f
Page 1049 of 1501
![MITSUBISHI MONTERO 1998 Manual PDF \b\
\
\
\
\
\
\
Engine Oil Oil Pan](/img/19/57333/w960_57333-1048.png "MITSUBISHI MONTERO 1998 Manual PDF \b\
\
\
\
\
\
\
Engine Oil Oil Pan")
\b\
\
\
\
\
\
\
Engine Oil Oil Pan 4.5 Qts. (4.3L)
(
1) \b \
\
\
\
\
Oil Filter 0.32 Qts. (0.3L)
\b
\
\
\
\
\
Oil Cooler 0.32 Qts. (0.3L)
\b
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick to measure level.
\f
\
\
\
\
\
\
\
30,000 MILE (48,000 KM) NORMAL SERVICE
30,000 MILE (48,000 KM) NORMAL SERVICE\
\
\
\
\
\
\
VERIFY
\b
\
\
\
\
\
\
\
Last Major Service Was Performed
\b
\
\
\
\
\
\
\
SERVICE
\b
\
\
\
\
\
\
\
Ball Joints With Grease Nipple (
6)
\b
\
\
\
\
\
\
\
Propeller Shaft Joints (
6)
\b
\
\
\
\
\
\
\
INSPECT
\b
\
\
\
\
\
\
\
Fuel Hoses (
3)
\b
\
\
\
\
\
\
\
Drive Belt (For Generator, Water Pump, Power Steering Pump)
\b
\
\
\
\
\
\
\
Manual Transmission Oil
\b
\
\
\
\
\
\
\
Transfer Oil
\b
\
\
\
\
\
\
\
Disc Brake Pads (
4)
\b
\
\
\
\
\
\
\
Brake Hoses (
4)
\b
\
\
\
\
\
\
\
Ball Joint & Steering Linkage Seals (
3)
\b
\
\
\
\
\
\
\
Drive Shaft Boots (
4)
\b
\
\
\
\
\
\
\
Exhaust System (
3)
\b
\
\
\
\
\
\
\
REPLACE
\b
\
\
\
\
\
\
\
Engine Oil (
1)
\b
\
\
\
\
\
\
\
Engine Oil Filter (
2)
\b
\
\
\
\
\
\
\
Engine Coolant
\b
\
\
\
\
\
\
\
Automatic Transmission Fluid
\b
\
\
\
\
\
\
\
Rear Axle Oil
\b
\
\
\
\
\
\
\
Air Cleaner Filter
\b
\
\
\
\
\
\
\
(
1) - Change once a year or every 7,500 miles (12,000 KM).
(
2) - If mileage is less than 7,500 miles (12,000 KM) each year,
replace the oil filter at every oil change.
Page 1053 of 1501
![MITSUBISHI MONTERO 1998 Manual PDF LUBRICATION SPECIFICATIONS
\b
\
\
\
\
\
\](/img/19/57333/w960_57333-1052.png "MITSUBISHI MONTERO 1998 Manual PDF LUBRICATION SPECIFICATIONS
\b
\
\
\
\
\
\")
LUBRICATION SPECIFICATIONS
\b
\
\
\
\
\
\
\
Material Condition Specification
\b
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Less Than SAE 5W-30
(
1) 0 F (-18 C) To 100 F (38 C)
\b
\
\
\
\
\
Ambient Temperature Above 0 F SAE 10W-30
(-18 C) To Over 100 F (38 C)
\b
\
\
\
\
\
\
\
(
1) - SAE 5W-30 engine oil is preferred. SAE 10W-30 may be used if
the Ambient Temperature is above 0 F (-18 C).
\b
\
\
\
\
\
\
\
FLUID CAPACITIES
\b
\
\
\
\
\
\
\
Item Condition Specification (1)
\b
\
\
\
\
\
\
\
Engine Oil Oil Pan 4.5 Qts. (4.3L)
(
1) \b \
\
\
\
\
Oil Filter 0.32 Qts. (0.3L)
\b
\
\
\
\
\
Oil Cooler 0.32 Qts. (0.3L)
\b
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick to measure level.
\f
\
\
\
\
\
\
\
60,000 MILE (96,000 KM) NORMAL SERVICE
60,000 MILE (96,000 KM) NORMAL SERVICE\
\
\
\
\
\
\
VERIFY
\b
\
\
\
\
\
\
\
Last Major Service Was Performed
\b
\
\
\
\
\
\
\
SERVICE
\b
\
\
\
\
\
\
\
Ball Joints With Grease Nipple (
6)
\b
\
\
\
\
\
\
\
Propeller Shaft Joints (
6)
\b
\
\
\
\
\
\
\
INSPECT
\b
\
\
\
\
\
\
\
Fuel Hoses (
3)
\b
\
\
\
\
\
\
\
Fuel System (Tank, Pipe Line, Connection & Fuel Tank Filler
Tube Cap) (
3)
\b
\
\
\
\
\
\
\
Evaporative Emission Control System (Except Evaporative
Emission Canister) (
7)
\b
\
\
\
\
\
\
\
Drive Belt (For Generator, Water Pump, Power Steering Pump)
\b
\
\
\
\
\
\
\
Manual Transmission Oil
\b
\
\
\
\
\
\
\
Transfer Oil
\b
\
\
\
\
\
\
\
Disc Brake Pads (
4)
\b
\
\
\
\
\
\
\
Brake Hoses (
4)
\b
\
\
\
\
\
\
\
Ball Joint & Steering Linkage Seals (
3)
Page 1058 of 1501
![MITSUBISHI MONTERO 1998 Manual PDF 90,000 MILE (144,000 KM) NORMAL SERVICE\
\
\
\
\
\
\](/img/19/57333/w960_57333-1057.png "MITSUBISHI MONTERO 1998 Manual PDF 90,000 MILE (144,000 KM) NORMAL SERVICE\
\
\
\
\
\
\")
90,000 MILE (144,000 KM) NORMAL SERVICE\
\
\
\
\
\
\
VERIFY
\b
\
\
\
\
\
\
\
Last Major Service Was Performed
\b
\
\
\
\
\
\
\
SERVICE
\b
\
\
\
\
\
\
\
Ball Joints With Grease Nipple (
6)
\b
\
\
\
\
\
\
\
Propeller Shaft Joints (
6)
\b
\
\
\
\
\
\
\
INSPECT
\b
\
\
\
\
\
\
\
Fuel Hoses (
3)
\b
\
\
\
\
\
\
\
Drive Belt (For Generator, Water Pump, Power Steering Pump)
\b
\
\
\
\
\
\
\
Manual Transmission Oil
\b
\
\
\
\
\
\
\
Transfer Oil
\b
\
\
\
\
\
\
\
Disc Brake Pads (
4)
\b
\
\
\
\
\
\
\
Brake Hoses (
4)
\b
\
\
\
\
\
\
\
Ball Joint & Steering Linkage Seals (
3)
\b
\
\
\
\
\
\
\
Drive Shaft Boots (
4)
\b
\
\
\
\
\
\
\
Exhaust System (
3)
\b
\
\
\
\
\
\
\
REPLACE
\b
\
\
\
\
\
\
\
Engine Oil (
1)
\b
\
\
\
\
\
\
\
Engine Oil Filter (
2)
\b
\
\
\
\
\
\
\
Engine Coolant
\b
\
\
\
\
\
\
\
Automatic Transmission Fluid
\b
\
\
\
\
\
\
\
Rear Axle Oil
\b
\
\
\
\
\
\
\
Air Cleaner Filter
\b
\
\
\
\
\
\
\
(
1) - Change once a year or every 7,500 miles (12,000 KM).
(
2) - If mileage is less than 7,500 miles (12,000 KM) each year,
replace the oil filter at every oil change.
(
3) - Or inspect every 2 years.
(
4) - Or inspect every year.
(
5) - Or change every 2 years.
(
6) - Or lubricate grease every 2 years.
\b
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
\b
\
\
\
\
\
\
\
Material Condition Specification
\b
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Less Than SAE 5W-30
(
1) 0 F (-18 C) To 100 F (38 C)
\b
\
\
\
\
\
Ambient Temperature Above 0 F SAE 10W-30
(-18 C) To Over 100 F (38 C)
Page 1062 of 1501
![MITSUBISHI MONTERO 1998 Manual PDF FLUID CAPACITIES
\b
\
\
\
\
\
\](/img/19/57333/w960_57333-1061.png "MITSUBISHI MONTERO 1998 Manual PDF FLUID CAPACITIES
\b
\
\
\
\
\
\")
FLUID CAPACITIES
\b
\
\
\
\
\
\
\
Item Condition Specification (1)
\b
\
\
\
\
\
\
\
Engine Oil Oil Pan 4.5 Qts. (4.3L)
(
1) \b \
\
\
\
\
Oil Filter 0.32 Qts. (0.3L)
\b
\
\
\
\
\
Oil Cooler 0.32 Qts. (0.3L)
\b
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick to measure level.
\f
\
\
\
\
\
\
\
120,000 MILE (200,000 KM) NORMAL SERVICE
120,000 MILE (200,000 KM) NORMAL SERVICE\
\
\
\
\
\
\
VERIFY
\b
\
\
\
\
\
\
\
Last Major Service Was Performed
\b
\
\
\
\
\
\
\
SERVICE
\b
\
\
\
\
\
\
\
Ball Joints With Grease Nipple (
6)
\b
\
\
\
\
\
\
\
Propeller Shaft Joints (
6)
\b
\
\
\
\
\
\
\
INSPECT
\b
\
\
\
\
\
\
\
Fuel Hoses (
3)
\b
\
\
\
\
\
\
\
Fuel System (Tank, Pipe Line, Connection & Fuel Tank Filler
Tube Cap) (
3)
\b
\
\
\
\
\
\
\
Evaporative Emission Control System (Except Evaporative
Emission Canister) (
7)
\b
\
\
\
\
\
\
\
Drive Belt (For Generator, Water Pump, Power Steering Pump)
\b
\
\
\
\
\
\
\
Manual Transmission Oil
\b
\
\
\
\
\
\
\
Transfer Oil
\b
\
\
\
\
\
\
\
Disc Brake Pads (
4)
\b
\
\
\
\
\
\
\
Brake Hoses (
4)
\b
\
\
\
\
\
\
\
Ball Joint & Steering Linkage Seals (
3)
\b
\
\
\
\
\
\
\
Drive Shaft Boots (
4)
\b
\
\
\
\
\
\
\
Exhaust System (
3)
\b
\
\
\
\
\
\
\
Distributor Cap & Rotor (
7)
\b
\
\
\
\
\
\
\
REPLACE
\b
\
\
\
\
\
\
\
Engine Oil (
1)
\b
\
\
\
\
\
\
\
Engine Oil Filter (
2)
\b
\
\
\
\
\
\
\
Page 1067 of 1501
SEATS - POWER
1998 Mitsubishi Montero
1998 ACCESSORIES & EQUIPMENT
Mitsubishi - Power Seats
Eclipse, Galant, Montero, 3000GT
DESCRIPTION & OPERATION
Power seat system consists of reversible motors, a control
switch assembly and a wiring harness. Circuit is protected by a
fusible link, located in main relay box in engine compartment.
Power assist adjustments offered are: forward and backward
movement, height adjustment and separately adjusted front or rear seat
tilt. Controls are located on side of seat cushion or on center
console.
COMPONENT LOCATIONS
COMPONENT LOCATIONS TABLE \
\
\
\
\
\
Component Location
Data Link Connector (DLC) ............ Under Left Of Dash,
Below Steering Column
ETACS-ECU
3000GT ......................... Left Of Steering Column
Seat Adjusting Motors .............. Under Each Front Seat
\
\
\
\
\
\
COMPONENT TESTS
LIMIT SWITCH/SENSOR
Galant (Driver's Seat)
Disconnect each limit switch harness connector. Operate each
switch to check continuity between specified pins using ohmmeter. See
LIMIT SWITCH CONTINUITY TABLE (GALANT) . See Fig. 1. Replace power seat
adjuster assembly if any switch fails testing.
LIMIT SWITCH CONTINUITY TABLE (GALANT)
\
\
\
\
\
\
Switch Check Continuity
Position Between Pins No.
Slide Limit Switch
Forward .......................................... 1 & 2
Backward ......................................... 1 & 3
Middle (ON) ................................... 1, 2 & 3
Front & Rear Height Limit Switch
Front Up ......................................... 1 & 3
Front Down ....................................... 1 & 2
Front Middle (ON) ............................. 1, 2 & 3
Rear Up .......................................... 1 & 3
Rear Down ........................................ 1 & 2
Rear Middle (ON) .............................. 1, 2 & 3
\
\
\
\
\
\