check oil MITSUBISHI MONTERO 1998 Manual Online
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998Pages: 1501, PDF Size: 25.81 MB
Page 1244 of 1501
REAR SUSPENSION ASSEMBLY
NOTE: Procedures for Montero are for lateral rod, coil springs and
lower arms only. Procedures for Montero Sport are for leaf
springs only.
Removal (Montero)
1) Raise and support rear of vehicle. Place a jack under
center of rear axle housing. Remove parking brake cable attaching
bolts.
2) Remove rear speed sensor attaching bolt (if equipped).
Remove rear axle housing lock position harness attaching bolt and
lower shock bolts.
3) Remove lateral rod bolts and remove lateral rod. Remove
lower arm rear bolts. Remove lower arm front mounting nut and remove
lower arm. See Fig. 2.
Inspection
Check lateral rod for straightness and damage. Check rubber
bushings for deterioration, cracks and wear.
Installation
If lateral rod bushings need replacing, remove and install
using Lower Arm Bushing Arbor (MB990650). Apply a sufficient amount of\
liquid soap to bushings when installing them into lateral rod. If
lower arm rear bushings need replacing, remove and install rear
bushings using Rear Bushing Arbor (MB991293). To complete
installation, reverse removal procedure. Tighten all suspension
fasteners to specification with vehicle on ground and suspension
unloaded. See TORQUE SPECIFICATIONS .
Removal (Montero Sport)
1) Raise and support rear of vehicle. Place a jack under
center of rear axle housing.
2) Disconnect parking brake cable attaching bolts. Remove
rear speed sensor attaching bolt. Remove rear shock nuts and washers.
Remove rear shocks.
NOTE: The yellow shock mounts on left side and the pink one mounts
to the right side of vehicle.
3) Remove U-bolt nuts, U-bolt seat and U-bolts. Remove bump
stopper. Remove rear shackle plate nuts, shackle plate, bushings and
shackle assembly. Remove front shackle nuts and bolts. Remove leaf
spring. See Fig. 1.
Inspection
Check leaf springs for cracks and other damage. Inspect all
components and bushings for damage and wear. Replace components as
necessary.
Installation
To install, reverse removal procedure. Ensure shocks are
installed on proper side of vehicle. Tighten all suspension fasteners
to specification with vehicle on ground and suspension unloaded. See
TORQUE SPECIFICATIONS .
SHOCKS
Removal
1) Raise and support rear of vehicle. Place a jack under
center of rear axle housing. On Montero remove shock actuator (if
equipped).
Page 1245 of 1501
2) Remove upper shock mounting nuts and washers. On Montero
remove shock lower mounting nuts and bolts. On Montero Sport remove
shock lower mounting nuts and washers. Remove shock assembly.
Inspection
Check shock for oil leakage, abnormal noise and poor
function. Check coil spring for bending and weakness. Check rubber
parts for deterioration and cracks.
Installation
To install, reverse removal procedure. Tighten all fasteners
to specification. See TORQUE SPECIFICATIONS.
STABILIZER BAR
Removal
Raise and support vehicle. Support rear suspension assembly
using a jack. On Montero remove shock lower mounting bolts and nuts.
Remove stabilizer bar bracket and bushings. Remove stabilizer link
mounting nut and bolt. Remove stabilizer link joint cups, bushings and
collar. Remove stabilizer bar.
Inspection
1) Check bushings for wear and deterioration. Check
stabilizer bar, stabilizer link and all bolts for damage and wear.
Replace components as necessary.
Installation
To install, reverse removal procedure. When installing
stabilizer link, hold link using wrench and tighten nut until distance
from end of bolt to edge of nut is .59-.70" (15-17 mm). Tighten all
fasteners to specification. See TORQUE SPECIFICATIONS.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS \
\
\
\
\
\
\
Application Ft. Lbs. (N.m)\
Upper Shock Nut
Montero .................................................. 11 (15)\
Montero Sport ............................................ 16 (22)\
Lower Shock Nut And Bolt
Montero ........................................ 159-181 (216-245)\
Montero Sport ............................................ 16 (22)\
Lateral Rod Nut And Bolt
Montero ................................................. 170 (230)\
Lower Arm Rear Nut And Bolt
Montero ................................................. 170 (230)\
Lower Arm Front Nut
Montero ................................................. 101 (137)\
Leaf Spring Rear Shackle Nut
Montero Sport ............................................. 38 (52)\
Leaf Spring Front Shackle Nut And Bolt
Montero Sport ........................................... 145 (196)\
"U" Bolt Nut
Montero Sport ...................................... 72-87 (98-118)\
Stabilizer Bar Bracket Bolt .......................... 25-26 (34-35)\
\
\
\
\
\
\
\
Page 1250 of 1501
the facts, allowing the customer to draw their own
conclusions and make an informed decision about how to
proceed.
STEERING AND SUSPENSION
SERVICE PROCEDURES REQUIRED AND SUGGESTED FOR PROPER VEHICLE
OPERATION
Steering and suspension are complex systems made up of a
variety of interdependent components. For proper vehicle handling,
ride, and tire wear, a thorough inspection is required whenever
suspension work is being performed.
Conditions listed assume that the problem has been isolated
to the specific component by proper testing procedures.
NOTE: When replacing steering and/or suspension components which
may affect an alignment angle, you are required to check
and adjust alignment as needed. Refer to the OEM
specifications.
CAUTION: DO NOT use ride height altering or load compensating
components, such as variable rate springs and coil over
shocks, on vehicles with height or load sensing
proportioning valve-equipped braking systems, unless
these components are original equipment.
AIR RIDE SUSPENSION
NOTE: Depending on the air suspension design, there are some
aftermarket products available to eliminate the air ride
suspension on certain vehicles. If the system has been
eliminated with one of these products, then no service is
suggested or required.
AIR RIDE SUSPENSION - AIR SHOCKS AND AIR STRUTS
NOTE: This section covers the air spring portion of the
air shock or strut. For damping portion of shock
or strut conditions and procedures, refer to the
SHOCK ABSORBERS, STRUT CARTRIDGES AND STRUT ASSEMBLIES
section.
AIR RIDE SUSPENSION - AIR SHOCK AND AIR STRUT INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Inner fabric of air bag
damaged ................ A ............ Require replacement.
Leaking ................. A .. Require repair or replacement.
Outer covering of air bag
is cracked to the extent
that inner fabric of air
bag is visible ......... 1 ............ Suggest replacement.
\
\
\
\
\
\
\
AIR RIDE SUSPENSION - AIR SPRING VALVES
AIR RIDE SUSPENSION - AIR SPRING VALVE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Page 1270 of 1501
Stud loose in
taper hole ............. A ........... (7) Require repair or
replacement.
Taper hole elongated .... A ........ ( 8) Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ........ ( 7) Require replacement.
Wear exceeds
manufacturer's
specifications .......... B ............ Require replacement.
( 1) - If greaseable, grease joint. If problem persists or
joint is non-greaseable, require replacement.
( 2) - Cracked grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 3) - Lack of grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 4) - Torn grease boot will allow contaminants to enter the
joint and will accelerate wear.
( 5) - If manufacturer's procedures for inspection exist, use
those procedures; otherwise, use an approved inspection
method such as the dry park check.
CAUTION: DO NOT use pliers or pry bar to check ball and
socket movement. Use only moderate hand pressure.
( 6) - Excessive looseness is defined as being significant
enough to affect vehicle handling or structural
integrity.
( 7) - Check for damaged taper hole.
( 8) - Check for damaged stud.
\
\
\
\
\
\
\
SHOCK ABSORBERS, STRUT CARTRIDGES AND STRUT ASSEMBLIES
You are not required to replace shocks or struts in axle
sets. However, when replacing a shock or strut due to the conditions
that follow, you may suggest replacement of the other shock or strut
on the same axle for improved performance and preventive maintenance.
* Part is close to the end of its useful life
* To extend tire life
* To balance ride and handling
* To improve stopping distance
When replacing steering and/or suspension components which
may affect an alignment angle, you are required to check and adjust
alignment as needed. Refer to the OEM specifications.
Under no circumstances should a technician bend struts or
strut housings.
A vehicle's load-carrying and handling abilities are limited
by its suspension, tires, brakes, and driveline. Installing coil over
shocks or any other load assist device does not increase the vehicle's
load capacity. See the vehicle owner's manual for more details.
NOTE: If vehicle is equipped with original equipment coil over
shocks, apply the conditions for coil springs from the
SPRINGS - COIL, LEAF AND TORSION BAR section of the
STEERING AND SUSPENSION guidelines. If the vehicle is
equipped with add-on coil over shocks, you may suggest
replacing the shocks with standard shocks for any spring-
related condition.
SHOCK ABSORBER, STRUT CARTRIDGE AND STRUT ASSEMBLY INSPECTION
\
\
\
\
\
\
\
Page 1274 of 1501
![MITSUBISHI MONTERO 1998 Manual Online \
\
\
\
\
\
\
Condition Code](/img/19/57333/w960_57333-1273.png "MITSUBISHI MONTERO 1998 Manual Online \
\
\
\
\
\
\
Condition Code")
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
bent .................. B .... Require repair or replacement
of bent part.
Attaching hardware
broken ................ A .... Require replacement of broken
part.
Attaching hardware
corroded, affecting
structural integrity .. A .. Require replacement of corroded
part.
Attaching hardware
incorrect ............. A ........... Require replacement of
incorrect part.
Attaching hardware
loose ................. A .... Require repair or replacement
of loose part.
Attaching hardware
missing ............... C ... Require replacement of missing
part.
Attaching hardware
threads damaged ....... A .... Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ..... A ...... Require replacement of part
with stripped threads.
Broken (all springs
except secondary
leave(s) on multi-leaf
springs) .............. A ............. Require replacement.
Coil clash ............. .. .. (1) Require ride height check.
Coil spring insulator
deteriorated .......... 2 ........... Suggest replacement of
insulator.
Coil spring insulator
missing ............... 2 ........... Suggest replacement of
insulator.
Coil spring insulator
split ................. 2 ........... Suggest replacement of
insulator.
Coil spring plastic
coating deteriorated -
rust present .......... A ...... ( 2) Refer to manufacturer's
service requirements.
Composite spring
damaged ............... .. .......... ( 3) Further inspection
required.
Cracked (all springs
except composite leaf and
secondary leave(s) on
multi-leaf springs) ... A ............. Require replacement.
Installed incorrectly .. B .................. Require repair.
Leaf spring insulators
missing ............... 2 ........... Suggest replacement of
insulators.
Secondary leaf on multi-
leaf spring broken .... 1 .... Suggest repair or replacement
Secondary leaf on multi-
leaf spring cracked ... 1 .... Suggest repair or replacement
Torsion bar
Page 1357 of 1501
TRANSMISSION SERVICING - A/T
1998 Mitsubishi Montero
1997-98 TRANSMISSION SERVICING
Mitsubishi Automatic Transmission
Diamante, Eclipse, Galant, Mirage, Montero, 3000GT
IDENTIFICATION
AUTOMATIC TRANSMISSION APPLICATIONS \
\
\
\
\
\
\
Model Transmission/Transaxle
Diamante ..................................... Model F4A51 Transaxle
Eclipse
AWD ........................................ Model W4A33 Transaxle
FWD
2.0L Non-Turbo ........................... Model F4AC1 Transaxle
2.0L Turbo ............................... Model F4A33 Transaxle
2.4L ....................................... Model F4A23 Transaxle
Galant ....................................... Model F4A23 Transaxle
Mirage
1.5L ....................................... Model F4A41 Transaxle
1.8L ....................................... Model F4A42 Transaxle
Montero
2WD ..................................... Model R4AW3 Transmission
4WD ..................................... Model V4AW3 Transmission
3000GT ....................................... Model F4A33 Transaxle
\
\
\
\
\
\
\
LUBRICATION
SERVICE INTERVALS
Transaxle/Transmission
Check fluid level every 12 months or 15,000 miles. Change
fluid and filter every 30,000 miles. If vehicle is operated under
severe conditions, change fluid more often. If severe darkening of
fluid and strong odor are noted, bands should also be adjusted.
Transfer Case
On 4WD and AWD models, change transfer case fluid every 30,
000 miles.
CHECKING FLUID LEVEL
Transaxle/Transmission
1) Park vehicle on level area. Ensure oil is at normal
operating temperature, parking brake is engaged, and engine is at
idle. Move gear selector through each position, stopping briefly at
each selection.
2) Place gear selector in Neutral, and clean area around
dipstick tube. Ensure fluid level is between lower and upper marks,
but never over upper mark, in HOT range. Add or drain fluid if
necessary.
CAUTION: If severe darkening of fluid and strong odor are noted,
change fluid and filter, and adjust bands.
Transfer Case (All Others)
Page 1359 of 1501
removed to drain fluid. Remove oil filter/screen if necessary.
2) If oil filter/screen is replaced, tighten bolts to
specification. See TORQUE SPECIFICATIONS . Clean oil pan, replace
gasket, and install oil pan. Tighten oil pan bolts and drain plug to
specification. See TORQUE SPECIFICATIONS . Ensure dipstick hole area is
clean. Fill transmission with Dexron-II ATF, through filler tube,
until COLD level is reached on dipstick. Start engine, and allow to
idle for 2 minutes.
3) Shift transmission into each position, ending in Neutral.
Check fluid level with engine running at idle. If necessary, add
sufficient fluid to bring level to lower mark of dipstick. Recheck
fluid level after transmission is at normal operating temperature.
Transfer Case
Drain plug is located on bottom of transfer case. Change
drain plug gasket whenever fluid is changed. Lubricant level should be
at bottom of fill hole on side of transfer case.
ADJUSTMENTS
KICKDOWN SERVO
Eclipse, Galant & 3000 GT
1) Remove all dirt and grease around kickdown servo switch.
Remove snap ring and kickdown servo switch.
2) To prevent servo piston from turning, install Adapter
(MD998915) and Kickdown Servo Wrench (MD998918) so tab of wrench
engages with notch of piston. See Fig. 1.
CAUTION: DO NOT push servo piston inward while installing adapter and
servo wrench. Install adapter in brake pressure port by hand
ONLY. DO NOT use wrench to tighten adapter.
Fig. 1: Adjusting Kickdown Servo (Eclipse, Galant & 3000 GT)
Courtesy of Mitsubishi Motor Sales of America.
3) Loosen lock nut to "V" channel of adjuster rod. Tighten
inner section of Kickdown Service Adjustment Assembly (MD998916) until\
Page 1364 of 1501
TRANSMISSION SERVICING - M/T
1998 Mitsubishi Montero
1997-98 TRANSMISSION SERVICING
Mitsubishi Manual Transmission
Eclipse, Galant, Mirage, Montero, 3000GT
IDENTIFICATION
MANUAL TRANSMISSION APPLICATIONS \
\
\
\
\
\
\
Model Transmission/Transaxle (Model)\
Eclipse
AWD .................................... 5-Speed Transaxle (W5M33)\
FWD
2.0L Non-Turbo ....................... 5-Speed Transaxle (F5MC1)\
2.0L Turbo ........................... 5-Speed Transaxle (F5M33)\
2.4L ................................. 5-Speed Transaxle (F5M31)\
Galant ................................... 5-Speed Transaxle (F5M31)\
Mirage
1.5L ................................... 5-Speed Transaxle (F5M41)\
1.8L ................................... 5-Speed Transaxle (F5M42)\
Montero
2WD ................................. 5-Speed Transmission (R5M21)\
4WD ................................. 5-Speed Transmission (V5MT1)\
3000GT
SOHC & DOHC Non-Turbo .................. 5-Speed Transaxle (F5M33)\
DOHC Turbo ............................. 6-Speed Transaxle (W6MG1)\
\
\
\
\
\
\
\
LUBRICATION
SERVICE INTERVALS
Check transaxle/transmission and transfer case fluid level
every 30,000 miles. Change fluid at 30,000 miles if operated under
severe conditions.
CHECKING FLUID LEVEL
Transaxle/Transmission
Check fluid level at fill hole on side of transaxle or
transmission. Lubricant must be at bottom of fill hole.
Transfer Case
Transfer case contains separate drain and fill plugs.
Lubricant must be at bottom of fill hole.
RECOMMENDED FLUID
Transaxle/Transmission
Use API classification GL-4 or higher SAE 75W-85W gear oil.
Transfer Case
Use API classification GL-4 or higher SAE 75W-85W gear oil.
FLUID CAPACITIES
TRANSAXLE/TRANSMISSION REFILL CAPACITIES
Page 1368 of 1501
![MITSUBISHI MONTERO 1998 Manual Online Defective diodes or stator See Bench Test in
ALTERNATOR article
\
\
\](/img/19/57333/w960_57333-1367.png "MITSUBISHI MONTERO 1998 Manual Online Defective diodes or stator See Bench Test in
ALTERNATOR article
\
\
\")
Defective diodes or stator See Bench Test in
ALTERNATOR article
\
\
\
\
\
\
\
Battery Does Loose or worn drive belt Check alternator drive
Stay Charged belt tension and
condition. See
Belt Adjustment in
appropriate TUNE-UP
article in the
TUNE-UP section
Loose or corroded battery Check all charging
connections system connections
Loose alternator connections Check all charging
system connections
Defective alternator or See On-Vehicle Tests
battery and Bench Tests in
ALTERNATOR article
Add-on electrical accessories Install larger
exceeding alternator capacity alternator
\
\
\
\
\
\
\
Battery Defective battery Check alternator
Overcharged- output and repair as
Uses Too Much necessary
Water
Defective alternator See On-Vehicle Test and
Bench Tests in
ALTERNATOR article
Excessive alternator voltage Check alternator output
and repair as necessary
\
\
\
\
\
\
\
IGNITION SYSTEM TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
Ignition Secondary Trouble Shooting Chart
\
\
\
\
\
\
START: Visually inspect Spark Plug Wires, Coil Wires,
Plug Wire Boots, Rotor, and Distributor Cap for
signs of damage.
\
\
\
\
\
\
\b
\
\
\
\
\
\
OK NOT OK
\b \b
\
\
\
\
\
* To test secondary ignition * Repair or replace
system, modify a Spark Plug damaged components
by attaching a ground wire as necessary
to the body of the plug and
\
\
\b
Page 1369 of 1501
widening the gap to 1/4-3/8".
Disconnect spark plug wire
and insert test plug. Ground
plug, crank engine, and
check for spark.
\
\
\
\b
\
\
\
\
\
\
\
GOOD SPARK NO SPARK
\
\b \
\b
\
\
\
\
\
\
* If plug sparks, driveability * Remove coil wire from the
problem is most likely NOT distributor and attach the
in the ignition system. modified spark plug. Ground
\
\
\
\b
the plug and crank engine
while checking for spark.
\
\
\
\b
\
\
\
\
\
\
\
GOOD SPARK NO SPARK
\
\b \
\b
\
\
\
\
\
\
* If plug has a good spark, * Proceed to the IGNITION
the problem is in the plug PRIMARY TROUBLE SHOOTING
wires, distributor cap, or CHECK CHART below in this
rotor. Replace components article.
as necessary.
\
\
\
\b
\
\
\
\b
Ignition Primary Trouble Shooting Chart
\
\
\
\
\
\
START: Visually inspect primary ignition wires for
broken, frayed, split, or cut wires. Also check
for loose, corroded, or disconnected connectors.
\
\
\
\
\
\
\b
\
\
\
\
\
\
OK NOT OK
\b \b
\
\
\
\
\
\
* Check that battery voltage * Repair or replace damaged
is at least 11.5 volts. components as necessary.
\
\
\
\b
\
\
\
\b
\
\
\
\
\
\
NOT OK OK
\b \b
\
\
\
\
\
\
* Replace or recharge the * Check for battery voltage
battery. at the positive terminal of
\
\
\
\b
the coil.
\
\
\
\b
\
\
\
\
\
\
OK NOT OK
\b \b
\
\
\
\
\
\
* Check air Gap of the Pick-Up * Check resistance of ballast
coil in the distributor. resistor (if used) for the
\
\
\
\b
correct resistance value.
\
\
\
\b
\
\
\