brake sensor MITSUBISHI MONTERO 2000 Service Owner's Manual

AUTOMATIC TRANSMISSION -Troubleshooting 23-40
Code No.45 5th without completion of shiftingProbable cause
If the output shaft speed sensor output multiplied by the 5th gear ratio is not
identical to the input shaft speed sensor output after shifting to 5th, code No. 45
is output.
If code No. 45 is output 4 times, the transmission is fixed in 3rd and the N
range lampflashes at a rate of 1 Hz.DMalfunction of input shaft speed sensor
DMalfunction of output shaft speed sensor
DMalfunction of harness or connector
DMalfunction of solenoid valve
DMalfunction of reverse clutch retainer
DMalfunction of direct planetary carrier
DMalfunction of 2ND brake system
DMalfunction of OD clutch system
DMalfunction of DIR clutch system
DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of A/T-ECU.<4M4>
DNoise is generated.
LRefer to the Transmission Workshop Manual.
Repair
NO
YES
YES
MUT-
IISelf-Diag Code
DIs code No. 22 output?Code No. 22 Input shaft speed sensor system check
(Refer to P.23-20.)
OK NO
Code No. 23 Output shaft speed sensor system check
(Refer to P.23-22.)MUT-
IIActuator Test
DIs code No. 23 output?
NG
NGMUT-
IIActuator Test
DNo.1 LR solenoid valve
DNo.2 UD solenoid valve
DNo.3 2ND solenoid valve
DNo.4 OD solenoid valve
DNo.5 RED solenoid valve
OK:The sound of operation should be heard.Replace the appropriate solenoid valve.
L
DCheck the harness between the input shaft speed sensor
and the engine-A/T-ECU. <6G7>
DCheck the harness between the input shaft speed sensor
and the A/T-ECU.<4M4>
Replace the input shaft speed sensor.
LNG
Check the trouble symptoms.
Overhaul the A/T.
L
DReplace the reverse clutch retainer.
Check the trouble symptoms.
Eliminate the cause of the noise.To the nextpage
Measure the output wave pattern of the input shaft speed
sensor at engine-A/T-ECU connectors D-121 and D-122
<6G7>, or at A/T-ECU connector D-108<4M4>(using an
oscilloscope).
DVehicle speed: approx. 50 km/h
DShift range: 4th
<6G7> Voltage between No.81 (D-121) and No.103 (D-122)
<4M4> Voltage between No.31(D-108) and No.43 (D-108)
OK:A wave pattern such as the one shown on P.23-69
(Check Procedure Using an Oscilloscope) should be
output, and the maximum value should be 4.8 V or more
and the minimumvalue should be 0.8 V or less. There
should be no noise in the output wave pattern.
OKNG
NG OK


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-41
NG
Replace the valve body assembly.
L
Check the trouble symptoms.
Replace the engine-A/T-ECU or A/T-ECU.
Check the trouble symptoms.
Repair
OK
NGDCheck the harness between the output shaft speed sensor
and the engine-A/T-ECU. <6G7>
DCheck the harness between the output shaft speed sensor
and the A/T-ECU.<4M4>
Replace the output shaft speed sensor.
L OK
Check the trouble symptoms.
Overhaul the A/T.
L
DReplace the direct planetary carrier.
Check the trouble symptoms.
Eliminate the cause of the noise.
From the previouspage
Measure the output wave pattern of the output shaft speed
sensor at engine-A/T-ECU connectors D-121 and D-122
<6G7>, or at A/T-ECU connector D-108<4M4>(using an
oscilloscope).
DVehicle speed: approx. 50 km/h
DShift range: 4th
<6G7> Voltage between No.81 (D-121) and No.104 (D-122)
<4M4> Voltage between No.32(D-108) and No.43 (D-108)
OK:A wave pattern such as the one shown on P.23-69
(Check Procedure Using an Oscilloscope) should be
output, and the maximum value should be 4.8 V or more
and the minimumvalue should be 0.8 V or less. There
should be no noise in the output wave pattern.
OK
NG
Overhaul the A/T.
L
DReplace the OD clutch. (Code No. 43 or No. 44 is output,
or no other codes are output.)
DReplace the 2ND brake. (Code No. 42 is output, or no
other codes are output.)
DReplace the DIR clutch. (Code No. 44 is output, or no
other codes are output.)NG
NG NG


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-42
Code No. 46 Reverse without completion of shiftingProbable cause
If the output shaft speed sensor output multiplied by the reverse gear ratio is not
identical to the input shaft speed sensor output after shifting to reverse, code
No. 46 is output.
If code No. 46 is output 4 times, the transmission is fixed in 3rd and the N
range lampflashes at a rate of 1 Hz.DMalfunction of input shaft speed sensor
DMalfunction of output shaft speed sensor
DMalfunction of harness or connector
DMalfunction of solenoid valve
DMalfunction of reverse clutch retainer
DMalfunction of direct planetary carrier
DMalfunction of LR brake system
DMalfunction of REV clutch system
DMalfunction of RED clutch system
DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of A/T-ECU<4M4>
DNoise is generated.
LRefer to the Transmission Workshop Manual.
Repair
NO
YES
YES
MUT-
IISelf-Diag Code
DIs code No. 22 output?Code No. 22 Input shaft speed sensor system check
(Refer to P.23-20.)
OK NO
Code No. 23 Output shaft speed sensor system check
(Refer to P.23-22.)MUT-
IIActuator Test
DIs code No. 23 output?
NG
NGMUT-
IIActuator Test
DNo.1 LR solenoid valve
DNo.2 UD solenoid valve
DNo.3 2ND solenoid valve
DNo.4 OD solenoid valve
DNo.5 RED solenoid valve
OK:The sound of operation should be heard.Replace the appropriate solenoid valve.
L
DCheck the harness between the input shaft speed sensor
and the engine-A/T-ECU. <6G7>
DCheck the harness between the input shaft speed sensor
and the A/T-ECU.<4M4>
Replace the input shaft speed sensor.
LNG
Check the trouble symptoms.
Overhaul the A/T.
L
DReplace the reverse clutch retainer.
Check the trouble symptoms.
Eliminate the cause of the noise.To the nextpage
Measure the output wave pattern of the input shaft speed
sensor at engine-A/T-ECU connectors D-121 and D-122
<6G7>, or at A/T-ECU connector D-108<4M4>(using an
oscilloscope).
DVehicle speed: approx. 50 km/h
DShift range: 4th
<6G7> Voltage between No.81 (D-121) and No.103 (D-122)
<4M4> Voltage between No.31(D-108) and No.43 (D-108)
OK:A wave pattern such as the one shown on P.23-69
(Check Procedure Using an Oscilloscope) should be
output, and the maximum value should be 4.8 V or more
and the minimumvalue should be 0.8 V or less. There
should be no noise in the output wave pattern.
OKOK
NG
NG


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-43
NG
Replace the valve body assembly.
L
Check the trouble symptoms.
Replace the engine-A/T-ECU or A/T-ECU.
Check the trouble symptoms.
Repair
OK
NGDCheck the harness between the output shaft speed sensor
and the engine-A/T-ECU. <6G7>
DCheck the harness between the output shaft speed sensor
and the A/T-ECU.<4M4>
Replace the output shaft speed sensor.
L OK
Check the trouble symptoms.
Overhaul the A/T.
L
DReplace the reverse clutch.
Check the trouble symptoms.
Eliminate the cause of the noise.
From the previouspage
Measure the output wave pattern of the output shaft speed
sensor at engine-A/T-ECU connectors D-121 and D-122
<6G7>, or at A/T-ECU connector D-108<4M4>(using an
oscilloscope).
DVehicle speed: approx. 50 km/h
DShift range: 4th
<6G7> Voltage between No.81 (D-121) and No.104 (D-122)
<4M4> Voltage between No.32(D-108) and No.43 (D-108)
OK:A wave pattern such as the one shown on P.23-69
(Check Procedure Using an Oscilloscope) should be
output, and the maximum value should be 4.8 V or more
and the minimumvalue should be 0.8 V or less. There
should be no noise in the output wave pattern.
OK
NG
Overhaul the A/T.
L
DReplace the LR brake. (Code No. 41 is output, or no other
codes are output.)
DReplace the REV clutch. (No other codes are output.)
Replace the RED brake. (Code No. 41, 42 or No. 43 is
output, or no other codes are output.)NG
NG NG
Code No. 51 Communication problem with engine-ECUProbable cause
If normal communication cannot be carried outsuccessfully for 1 second or
more when the ignition switch is at the ON position, the system voltage is 10 V
or higher and the enginespeed is 450 r/min or higher, code No. 51 is output.
Furthermore, code No. 51 is also output if a communication problem with
receiving data continues for 4 seconds or more under the same conditions.DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of engine-ECU <4M4>
DMalfunction of A/T-ECU<4M4>
DMalfunction of harness or connector<4M4>
Check the following connectors:D-112, D-109NG
Repair
OK
NG
Repair
OK
Check the trouble symptoms.
NG
Replace the engine-ECU.Check the trouble symptoms.NG
<4M4>
<6G7>
Check the harness between the engine-ECU and the
A/T-ECU.
Malfunction of A/T-ECU
Malfunction of engine-A/T-ECU


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-57
Inspection procedure 14
Poor acceleration
Probable cause
If the vehicle does not accelerate after downshifting, the cause is probably a
malfunction of the enginesystem or of a brake or clutch.DMalfunction of enginesystem
DMalfunction of brake or clutch
DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of A/T-ECU<4M4>
LRefer to the Transmission Workshop Manual.
Engine system check
DControl system, ignition system, fuel system, vehicle bodyNG
Repair or replace
OK
Brake and clutch check
L
DCheck for a problem such as burnt facing, poor piston
sealing or interference with the retainer.Check the trouble symptoms.
Replace the engine-A/T-ECU or A/T-ECU.NG
Inspection procedure 15
Vibration
Probable cause
If vibration occurs when accelerating or decelerating while driving at a constant
speed or driving in top range, the cause is probably abnormal damper clutch
pressure, or a malfunction of theenginesystem, DCC solenoid valve, torque
converter or valve body.DAbnormal damper clutch pressure
DMalfunction of enginesystem
DMalfunction of DCC solenoid valve
DMalfunction of torque converter
DMalfunction of valve body
DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of A/T-ECU<4M4>
LRefer to the Transmission Workshop Manual.
NGReplace the DCC solenoid valve.
L
OK
Does the problem still occur when theengine coolant
temperature sensor is disconnected?YESEngine system check
DControl system, ignition system, fuel system, vehicle body
NO
Fluid pressure test (Refer to P.23-106.)
DMeasure the damper clutch fluid pressure.
Standard value:Refer to P.23-106.NGDisassemble, clean and re-assemble the valve body.
L
DMake sure that the mounting bolts are not loose and that
the O-ring and valve body are notdamaged or positioned
incorrectly.
DIf the extent of thedamagelooks too bad for repairs to be
carried out, replace the valve body assembly.
OK
Replace the torque converter assembly.Check the trouble symptoms.
Replace the engine-A/T-ECU or A/T-ECU.OK
MUT-
IIActuator Test
DNo. 6 DCC solenoid valve
OK:Sound of operation can be heard


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-61
DATA LIST REFERENCE TABLE
Data
list No.Check itemInspection conditionsNormal condition
11APSIgnition switch: ON
Engine: StoppedAccelerator pedal:
Fully closed985 - 1085 mV
Engine: Stopped
Selector lever posi-
tion: P
Accelerator pedal:
DepressedGradually increases from the above
value.
Accelerator pedal:
Fully open4000 mV or higher
15A/T fluid tempera-
ture sensorDriving after en-
gine has warmed
upDrive for 15 minutes
or more until the ATF
temperature reaches
70 - 80°C.Gradually increases to 70 - 80°C.
21Crank angle sen-
sor <6G7>Engine: Idling
Selector lever posi-Compare the engine
speeds displayed onIdentical
sor <6G7>
Engine speed sen-
sor <4M4>Selector lever posi-
tion: Pspeeds displayed on
the tachometer and
the MUT-II.
22Input shaft speed
sensorShift range: 4thDriving at a constant
speed of 50 km/h in
4th1300 - 1600 r/min
23Output shaft speed
sensorShift range: 4thDriving at a constant
speed of 50 km/h in
4th1300 - 1600 r/min
25Wide open throttleAccelerator pedalReleasedOFF
switchpositionDepressedON
26Stop lamp switchIgnition switch: ON
Engine: StoppedBrake pedal: De-
pressedON
Engine: Stopped
Brake pedal: Re-
leasedOFF
29Vehicle speed sen-
sorSelector lever posi-
tion: Sports modeIdling in 1st
(Vehicle stopped)0 km/h
Driving at a constant
speed of 50 km/h in
3rd50 km/h
31LR solenoid valve
duty ratioSelector lever posi-
tion: Sports modeData List No.No. 31No. 32No. 33No. 34No.35
32UD solenoid valve
duty ratioDriving at a constant
speed in 1st0%0%100%100%0%
332nd solenoid valve
duty ratioDriving at a constant
speed in 2nd100%0%0%100%0%
34OD solenoid valve
duty ratioDriving at a constant
speed in 3rd100%0%100%0%0%
35RED solenoid
valve duty ratioDriving at a constant
speed in 4th0%0%100%0%100%
Driving at a constant
speed in 5th100%100%0%0%100%


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-68
Ter-
minal
No.Standard value Inspection conditions Check item
54Input communication withEngine: IdlingOther than 0 V
engine-ECUSelector lever position: D
55Inhibitor switch PIgnition switch: ON
Selector lever position: PSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
56Inhibitor switch NIgnition switch: ON
Selector lever position: NSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
57Select switchIgnition switch: ON
Selector lever operation: Sports modeSystem voltage
Ignition switch: ON
Selector lever operation: Other than the above0V
58Downshift switchIgnition switch: ON
Selector lever position: Downshifted in Sports mode
and lever heldSystem voltage
Ignition switch: ON
Selector lever operation: Other than the above0V
59Stop lamp switchIgnition switch: ON
Brake pedal DepressedSystem voltage
Ignition switch: ON
Brake pedal Released0V
62DIR solenoid valveEngine: Idling
Shift range: ParkSystem voltage
Engine: Idling
Shift range: 2nd7-9V
65Wide open throttle switchAccelerator pedal: Released4.5 - 5.5 V
Accelerator pedal: DepressedLess than 0.4 V
66Inhibitor switch RIgnition switch: ON
Selector lever position: RSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
67Inhibitor switch DIgnition switch: ON
Selector lever position: DSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
68Upshift switchIgnition switch: ON
Selector lever position: Upshifted in Sports mode and
lever heldSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
69Vehicle speed sensorWhen stopped0V
When starting to drive forward slowly.0 V and 5 V alter-
nates
71A/T control relayIgnition switch: OFF0V
Ignition switch: ON10 - 12 V
72EarthIgnition switch: ON0V


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting II>23-90
Ter-
minal
No.Check itemInspection conditionsStandard value
1Shift actuatorTransfer shift lever position: 2H®4H5.6 V®11.0 V®
5.6 V
3Shift actuatorTransfer shift lever position: 4H®2H5.6 V®11.0 V®
5.6 V
5Accelerator pedal positionAccelerator pedal: Fully closed (engine stopped)0.985 - 1.085 V
sensor (APS)Accelerator pedal: Fully open (engine stopped)4.0 V or higher
7Front propeller shaft speed
sensorMeasure the voltage between terminals 7 and 18 using
an oscilloscope.
Engine: 2 000 r/min
Shift range: 4thOscilloscope check
procedure (Refer to
P. 23-69 Pattern B>.)
9Rear propeller shaft speed
sensorMeasure the voltage between terminals 9 and 18 using
an oscilloscope.
Engine: 2 000 r/min
Shift range: 4thOscilloscope check
procedure (Refer to
P. 23-69 Pattern B>.)
11Diagnosis outputWhen normal (no diagnosis codes are output)0 V and 5 V alterna-
tes
13Power supplyIgnition switch: OFF0V
Ignition switch: ONSystem voltage
18Sensor earthAt all times0.5 V or less
20Transfer lever switch 2HTransfer shift lever position: 2HSystem voltage
Transfer shift lever position: Other than the above0V
21Transfer lever switch 4HTransfer shift lever position: 4HSystem voltage
Transfer shift lever position: Other than the above0V
22Transfer lever switch 4HLcTransfer shift lever position: 4HLcSystem voltage
Transfer shift lever position: Other than the above0V
23Transfer lever switch 4LLcTransfer shift lever position: 4LLcSystem voltage
Transfer shift lever position: Other than the above0V
24Diagnosis control––
25EarthAt all times0V
26EarthAt all times0V
31Backup power supplyAt all timesSystem voltage
32Inhibitor switch NSelector lever position: NSystem voltage
Selector lever position: Other than the above0V
33Inhibitor switch PSelector lever position: PSystem voltage
Selector lever position: Other than the above0V
34Stop lamp switchBrake pedal: DepressedSystem voltage
Brake pedal: Released0V
35EarthAt all times0V
37Rear wheel indicator lampOther than during transfer selectionSystem voltage
38Front wheel indicator lampDuring 4WDSystem voltage
39Earth <6G7>At all times0V


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

35A-2
BASIC BRAKE
SYSTEM
CONTENTS
GENERAL INFORMATION 3..................
SERVICE SPECIFICATIONS 5.................
LUBRICANTS 6..............................
SPECIAL TOOLS 6..........................
TROUBLESHOOTING
7......................
ON-VEHICLE SERVICE 19...................
Brake Pedal Check and Adjustment 19..........
Hydraulic Brake Booster (HBB) Operation Check
20........................
HBB Check 23............
HBB Motor Relay Continuity Check
24........................
Brake Booster Operating Test
24.....................
Check Valve Operation Check
25.....................
Load Sensing Spring Length Check and
Adjustment 25.........
Load Sensing Proportioning Valve Function
Test 26................
Bleeding 27...............Bleeding 29.............
Brake Fluid Level Sensor Check 30.............
Brake Booster Vacuum Switch Check
30..................
Disc Brake Pad Check and Replacement 31.....
Disc Brake Rotor Check 32.....................
Brake Disc Thickness Check 32.................
Brake Disc Run-out Check and Correction 33....
BRAKE PEDAL 34..........................
HYDRAULIC BRAKE BOOSTER (HBB)
36....................
HBB BUZZER 40......
MASTER CYLINDER AND BRAKE
BOOSTER 41......
Master Cylinder 43.............................
FRONT DISC BRAKE 44....................
REAR DISC BRAKE 49......................
LOAD SENSING PROPORTIONING
VALVE 54..........


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

35B-1
ANTI-SKID
BRAKING SYSTEM
(ABS) <4WD>
CONTENTS
GENERAL INFORMATION 2..................
SERVICE SPECIFICATIONS 4.................
LUBRICANT Refer to GROUP 35A...........
SEALANTS Refer to GROUP 35A............
SPECIAL TOOLS 4..........................
TROUBLESHOOTING 4.......................
ON-VEHICLE SERVICE 27...................
Wheel Speed Sensor Output Voltage
Measurement 27...............................
ABS Valve Relay Continuity Check 28...........
Hydraulic Brake Booster (HBB) - Hydraulic Unit
Check 29......................................
Solenoid Valve Check 30.......................
When the Battery is Flat 31....................
Brake Pedal Check and Adjustment
Refer to GROUP 35A ..........................
Hydraulic Brake Booster (HBB) Operation Check
Refer to GROUP 35A ..........................
Hydraulic Brake Booster (HBB) Check
Refer to GROUP 35A ..........................Motor Relay Continuity Check
Refer to GROUP 35A ..........................
Bleeding Refer to GROUP 35A..................
Brake Fluid Level Sensor Check
Refer to GROUP 35A ..........................
Disc Brake Pad Check and Replacement
Refer to GROUP 35A ..........................
Brake Disc Thickness Check
Refer to GROUP 35A ..........................
Brake Disc Runout Check and Correction
Refer to GROUP 35A ..........................BRAKE PEDAL Refer to GROUP 35A........
HYDRAULIC BRAKE BOOSTER (HBB)
Refer to GROUP 35A ........................
HBB BUZZER Refer to GROUP 35A..........
FRONT DISC BRAKE Refer to GROUP 35A..
REAR DISC BRAKE Refer to GROUP 35A....
ABS-ECU 32................................
WHEEL SPEED SENSOR 33.................
G-SENSOR 36..............................


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk