door lock MITSUBISHI MONTERO 2000 Service Owner's Manual

SWS -Troubleshooting54B-48
Inspection Procedure P-11
Front passenger’s or back door lock key cylinder switch
signal is not sent to the ETACS-ECU.Probable cause
The front passenger’s and back door lock key cylinder switch input signal is
used to operate the central door locking system. If the signal fails, central door
locking system will not work normally.DMalfunction of front passenger’s or back door lock
key cylinder switch
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
NG
Replace
OK
OK
Replace the ETACS-ECU.
OK
NG
NG
Repair
NG
RepairOK
NG
Check the harness wire between door lock key cylinder switch
and body earth.
NG
Check the harness wire between door lock key cylinder switch
and ETACS-ECU.NG
Repair
OK
Check trouble symptoms.
Check the following connectors:
Front passenger’s door: H-17, D-15, D-225
Back door: I-05, G-05, D-124, D-225
Check trouble symptoms.
Check the following connectors:
Front passenger’s door: H-17, D-15
Back door: I-05Measure at door lock key cylinder switch connector H-17 passenger’s door> or I-05 .
DDisconnect connector and measure at harness side
DContinuity between terminal 2 and body earth.
OK:Continuity
Check the door lock key cylinder switch. (Refer to GROUP 42
– Door or GROUP 42 - Back Door.)
Inspection Procedure P-12
Driver’s door lock actuator switch signal is not sent to the
ETACS-ECU.Probable cause
The driver’s door lock actuator switch is used to operate the following systems
or functions. If the signal fails, these systems or function will not work normally.
DCentral door locking system
DForgotten key prevention function
DKeyless entry systemDMalfunction of driver’s door lock actuator
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
OK
Replace the ETACS-ECU.
OK
NG
NG
Repair
NG
Repair
NG
Check the harness wire between driver’s door lock actuator and
body earth.
NG
Check the harness wire between driver’s door lock actuator and
ETACS-ECU.NG
Repair
OK
Check trouble symptoms.
OK
Check the following connectors:
H-03 , H-18 , D-25, D-225
OK
Check trouble symptoms.
Check the following connectors:
H-03 , H-18 , D-25Measure at door lock actuator connector H-03
or H-18 .
DDisconnect connector and measure at harness side
DContinuity between terminal 1 or 3

OK:Continuity
Check the door lock actuator switch. (Refer to GROUP 42 – Door
or Back Door.)NG
Replace


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

SWS -Troubleshooting54B-53
Inspection Procedure P-19
Center display: Any switch signal is not sent to the
ETACS-ECU.Probable cause
The cause is probably a malfunction of the center display or the ETACS-ECU.DMalfunction of center display
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector.
Ye s
NG
Repair
NG
Replace the ETACS-ECU.
OK
Replace the center display.Check trouble symptoms.
NG
Check the harness wire between center display and ETACS-ECU.NG
Repair
OK
Check trouble symptoms.
Check the following connectors:
D-06, D-31, D-226
Is the center display operated normally?NoCarry out troubleshooting for the center display. (Refer to
GROUP 54A – Center Display.)
Inspection Procedure Q-1
Check the circuit (power supply line) from the battery to
the ETACS-ECU.Probable cause
If that power supply circuit is defective, the circuit flowing through the ignition
switch (IG1) will function as a back-up circuit. In this case, the following
functions will not work when the ignition switch is at LOCK (OFF) position.
DIgnition key reminder warning buzzer function
DCentral door lock ing system
DIgnition key hole illumination lamp
DHazard warninglamp
DRoom lampDMalfunction of ETACS-ECU
DMalfunction of harness wire or connector.
NG
NG
Repair
NG
Check the harness wire between ETACS-ECU and fusible link
(2).
OK
Replace the ETACS-ECU.
OK
Check trouble symptoms.
Check the following connectors:
D-224, D-223, D-27Measure at ETACS-ECU connector D-224.
DDisconnect connector and measure at J/B side.
DVoltage between terminal 6 and body earth.
OK:System voltage


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

SWS -Troubleshooting54B-55
Terminal
No.Normal condition Checking requirements Check items
26Key reminder switch signal inputKey reminder switch: ON (Ignition key
removed)0V
27Hazard warning lamp switch signal
inputHazard warning lamp switch: ON0V
29Recognition line of daytime running
lamp (DRL) Always0V
31Data request signal outputAlways0 - 5 V (pulse
signal)
34Windshield intermittent wiper interval
adjusting knob signal inputIgnition switch: ACC,
Windshield intermittent wiper interval
adjusting knob: FAST®SLOW0®2.5 V
35Back-up lamp switch signal input
Ignition switch: ON,
Shift lever: RSystem voltage
Inhibitor switch (reverse) signal input
Ignition switch: ON,
Selector lever: RSystem voltage
36Ignition key hole illumination lamp
outputWhen ignition key hole illumination
lamp is lighted2 V or less
37Diagnosis code or input signal check
outputWhen diagnosis code is output0 - 12 V (pulse
signal)
When input signal check is output0, 12 V (When input
pulse signal is
changed)
40Rear fog lamp relay outputWhen rear fog lamp is lighted2 V or less
53Front passenger’s and back door lock
key cylinder switch (LOCK) signal inputFront passenger’s or back door lock key
cylinder switch: LOCK0V
54Front passenger’s and back door lock
key cylinder switch (UNLOCK) signal
inputFront passenger’s or back door lock
switch: UNLOCK0V
55Driver’s door lock actuator switch
(LOCK) signal inputDriver’s door lock actuator switch:
LOCK0V
56Driver’s door lock actuator switch
(UNLOCK) signal inputDriver’s door lock actuator switch:
UNLCOK0V


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

SWS -On-vehicle Service54B-60
ON-VEHICLE SERVICE
ADJUSTMENT PROCEDURES OF SWS FUNCTION
Through special operation of input switches, it is possible to disable and enable the functions listed below.
Settings are retained even if the battery is disconnected.
DKeyless entry hazard answerback function
DInitialization of above mentioned functions
Configuration Mode Entry Conditions
1. Set each switch at the following condition.
DHazard warning lamp switch: OFF
DDiagnosis control: ON (MUT-II
connected or terminal 1 of diagnosis connector connected to earth)
DKey reminder switch: OFF (ignition key inserted)
DIgnition switch: LOCK (OFF)
DDriver’s door switch: OFF (driver’s door closed)
2. When the windshield washer switch is continuously turned ON for more than 10 seconds, the buzzer
integrated in the ETACS-ECU sounds once and the mode is switched to the configuration mode.
Configuration Mode Cancellation Conditions
The ETACS-ECU cancels the configuration mode when any of the conditions listed below is satisfied.
DDiagnosis control: OFF (MUT-II
disconnected or terminal 1 of diagnosis connector disconnected from
earth)
DKey reminder switch: ON (ignition key removed)
DIgnition switch: any position other than LOCK (OFF)
DDriver’s door switch: ON (driver’s door open)
DNo configuration performed within three minutes of entry to configuration mode (If configuration is
performed within first three minutes, monitoring continues for three minutes from that point.)
Configuration of Functions
FunctionConfiguration procedure
Keyless entry hazard
answerbackIf the transmitter’s LOCK switch is turned ON twice within two seconds, the lock answerback
function’s enabled/disabled status is inverted.
D
When function is enabled, buzzer sounds once (initial status).
D
When function is disabled, buzzer sounds twice.
If the transmitter’s UNLOCK switch is turned ON twice within two seconds, the unlock
answerback function’s enabled/disabled status is inverted.
D
When function is enabled, buzzer sounds once (initial status).
D
When function is disabled, buzzer sounds twice.
Initialization of above
mentioned functionsIf the windshield washer switch is turned ON for more than 20 seconds, the buzzer sounds
twice and all functions are initialized. (The configuration mode entry buzzer sounds after 10
seconds, but the switch must be kept ON for 20 seconds to achieve initialization.)
IF the windshield washer switch ins kept ON for more than 20 seconds without prior entry
of the configuration mode, the configuration mode is entered after 10 seconds and
initialization does not take place.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk