headlamp MITSUBISHI MONTERO 2000 Service Owner's Manual

SWS -Troubleshooting54B-37
Inspection Procedure K-6
Headlamp, tail lamp: Headlamps dimmer switch automat-
ic reset function does not work normally.Probable cause
The headlamp dimmerswitch automatic reset function is controlled by the
front-ECU. If a defect appears, the front-ECU may be defective.DMalfunction of front-ECU
Replace the front-ECU.
Inspection Procedure K-7
Headlamp, tail lamp: Daytime running lamp (DRL) function
does not work.Probable cause
The headlamp dimmerswitch auto-reset function is controlled by the front-ECU.
If a defect appears, the front-ECU may be defective.DMalfunction of ETACS-ECU
DMalfunction of front-ECU
DMalfunction of harness wire or connector.
NoCheck the defective device. (Refer to P.54B-13, Trouble Symptom
Chart.)
Ye s
NG
NG
Repair
NG
Check the harness wire between ETACS-ECU and body earth.
OK
Replace the ETACS-ECU or front-ECU.
OK
Check trouble symptoms.
Check the following connectors:
D-226, D-27Measure at ETACS-ECU connector D-226.
DDisconnect connector and measure at harness side.
DContinuity between terminal 29 and body earth.
OK:Continuity
Are the tail lamp and headlamps operated normally?
Inspection Procedure L-1
Flasher timer: Turn-signal lamp do not flash when the
turn-signal lamp switch is turned on.Probable cause
The ETACS-ECU makes the turn-signal lamps flash, based on the input signals
from the following switches:
DIgnition switch (IG1)
DTurn-signal lampswitch
If the turn-signal lamps do not flash normally, a defect on the relevant circuits or
the ETACS-ECU may be suspected.
If the hazard warning lamps also do not flash, a defect in the ETACS-ECU
power supply line specific to the turn-signal lamps is suspected.DMalfunction of column switch
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

SWS -TroubleshootingSWS -Troubleshooting54B-39
Inspection Procedure M-1
Front fog lamp: Front fog lamps do not illuminate when the
front fog lamp switch is turned on.Probable cause
If the tail lamps and headlamps illuminate normally, the front fog lampswitch, the
front fog lamprelay, the front-ECU or the ETACS-ECU may be defective.DMalfunction of front fog lampswitch
DMalfunction of front fog lamprelay
DMalfunction of front-ECU
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector.
OK
Replace the front-ECU.Check trouble symptoms.
NGCheck the defective circuit. (Refer to P.54B-13, Trouble Symptom
Chart.)
OK
NG
Check the front foglampswitch input circuit. (Refer to P.54B-44,
Inspection Procedure P-5.)
OK
NG
NG
Repair
NG
Check the harness wire between front foglamprelay and battery.
OK
NG
Repair
NG
Check the harness wire between front foglamprelay and front-ECU,
front fog lamprelay and front fog lamps.NG
Repair
OK
Check trouble symptoms.
Check the following connectors:
A-09X, A-07X, A-15, A-26, A-22, A-33
OK
Check trouble symptoms.
Check the following connector:
A-09XMeasure at front fog lamprelay connector A-09X.
DDisconnect connector and measure at relay box side.
DVoltage between terminal 3 and body earth.
OK:System voltage
DVoltage between terminal 4 and body earth.
OK:System voltage
OK
Check the front foglamprelay. (Refer to GROUP 54A – Fog Lamp.)NG
Replace
MUT-
IIinput signal check
DFront fog lampswitch
Is the tail lamps and headlamps operated normally?
NG
Replace the ETACS-ECU.
NOTE
If only one of the front fog lamp or front fog lamp indicator lamp does not illuminate, the harness wire
between the lamp and front fog lamp relay may be defective or the lamp bulb may be burned out. In
this case, check the front fog lamp circuit.
Inspection Procedure M-2
Front fog lamp: Front fog lamp do not go out when the tail
lamps are turned off while the fog lamps are on.Probable cause
If the malfunction above occurs, the ETACS-ECU may be defective.DMalfunction of ETACS-ECU
Replace the ETACS-ECU.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

SWS -Troubleshooting54B-40
Inspection Procedure N-1
Rear fog lamp: Rear fog lamps do not illuminate when the
rear fog lamp switch is turned on.Probable cause
If the headlamps and rear fog lamps illuminate normally, the rear foglamp
switch, the rear foglamprelay or the ETACS-ECU may be defective.DMalfunction of rear foglampswitch
DMalfunction of rear foglamprelay
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector.
NoCheck the defective device. (Refer to P.54B-13, Trouble Symptom
Chart.)
Ye s
NG
Check the Rear foglampswitch input circuit. (Refer to P.54B-45,
Inspection Procedure P-6.)
OK
NG
Replace
OK
NG
NG
Repair
NG
Check the harness wire between rearlamprelay and fusible link
(1).
OK
NG
Repair
OK
Check trouble symptoms.
Check the following connectors:
D-212, D-226, D-26, D-124, G-02, G-07
OK
Check trouble symptoms.
Check the following connectors:
D-212, D-210, D-211, D-27Measure at rear foglamprelay connector D-212.
DDisconnect connector and measure at relay box side.
DVoltage between terminal 3 and body earth.
OK:System voltage
DVoltage between terminal 5 and body earth.
OK:System voltage
Check the rear foglamprelay. (Refer to GROUP 54A – Fog Lamp.)
MUT-
IIinput signal check
DRear foglampswitch
Are the headlamps and front fog lamps operated normally?
OK
Replace the ETACS-ECU.
NG
Check the harness wire between rear foglamprelay and ETACS-
ECU, rear foglamprelay and rear combination lamps.NG
Repair
NOTE
If only one of the rear fog lamp or rear fog lamp indicator lamp does not illuminate, the harness wire
between the lamp and rear fog lamp relay may be defective or the lamp bulb may be burned out. In
this case, check the rear fog lamp circuit.
Inspection Procedure N-2
Rear fog lamp: Rear fog lamp do not go out when the
headlamps and front fog lamps are turned off while the fog
lamps are on.Probable cause
If the malfunction above occurs, the ETACS-ECU may be defective.DMalfunction of ETACS-ECU
Replace the ETACS-ECU.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

SWS -Troubleshooting54B-42
Inspection Procedure P-1
Ignition switch (ACC) signal is not sent to the ETACS-ECU.Probable cause
The ignition switch (ACC) input signal is used to operate the following devices. If
the signal fails, these devices will not work normally.
DWindshield wiper and washer
DRear wiper and washer
DHeadlamp washerDMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
NG
NG
Repair
NG
Check the harness wire between ETACS-ECU and ignition switch
(ACC).
OK
Check trouble symptoms.OK
Replace the ETACS-ECU.
Check the following connectors:
D-224, D-208Measure at ETACS-ECU connector D-224.
DDisconnect connector and measure at J/B side.
DTurn the ignition switch to ACC position.
DVoltage between terminal 2 and body earth.
OK:System voltage
Inspection Procedure P-2
Ignition switch (IG1) signal is not sent to the ETACS-ECU.Probable cause
The ignition switch (IG1) input signal is used to operate the following devices. If
the signal fails, these devices will not work normally.
DLight reminder warning buzzer function
DPower window timer function
DSunroof timer function
DIgnition key hole illumination lamp
DHeadlamp automatic shutdown function
DTurn-signal lamp
DRoom lamp dimming functionDMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
NG
NG
Repair
NG
Check the harness wire between ETACS-ECU and ignition switch
(IG1).
OK
Check trouble symptoms.OK
Replace the ETACS-ECU.
Check the following connectors:
D-224, D-208Measure at ETACS-ECU connector D-224.
DDisconnect connector and measure at J/B side.
DTurn the ignition switch to ON position.
DVoltage between terminal 16 and body earth.
OK:System voltage


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

SWS -Troubleshooting54B-47
Inspection Procedure P-10
Driver’s door switch signal is not sent to the ETACS-ECU.Probable cause
Door switches signal is not sent to the ETACS-ECU.

The driver’s door switch is used to operate the following functions. If the signal
fails, these devices will not work normally.
DLight reminder warning buzzer function
DForgotten key prevention function
DPower window timer function
DIgnition key hole illumination lamp
DHeadlamp automatic shutdown function

The door switches is used to operate the following devices. If the signal fails,
these devices will not work normally.
DKeyless entry system
DRoom lamp dimming functionDMalfunction of driver’s, front passenger’s, rear or
back door switch
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
OK
NG
Repair
OK
NG
Repair
OK
Replace the ETACS-
ECU.
NG
Repair
NG
Check the harness wire between door switch and ETACS-ECU.
OKCheck trouble symptoms.
Check the following connectors :
Front L.H. door: F-20, D-26, D-218, D-224
Front R.H. door: F-03, D-124, D-209, D-224
Rear L.H. door: F-14, D-26, D-218, D-224
Rear R.H. door: F-10, D-124, D-209, D-224
Back door: G-03, D-26, D-218, D-224
Check the following connectors :
Front L.H. door: F-20, D-26, D-209, D-224
Front R.H. door: F-03, D-219, D-224
Rear L.H. door: F-14, D-26, D-209, D-224
Rear R.H. door: F-10, D-219, D-224
Back door: G-03, D-26, D-209, D-224
Check the installation of the door switch to the vehicle body.
Check the door switch. (Refer to GROUP 42 – Door or GROUP
42 - Back Door.)NG
Replace


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

SWS -Troubleshooting54B-49
Inspection Procedure P-13
Column switch:
D
Tail lamp switch signal is not sent to the ETACS-ECU.
D
Headlamp switch signal is not sent to the ETACS-ECU.
D
Dimmer switch signal is not sent to the ETACS-ECU.
D
Passing switch signal is not sent to the ETACS-ECU.
D
Turn-signal lamp switch signal is not sent to the
ETACS-ECU.
D
Headlamp washer switch is not sent to the ETACS-ECU.
Probable cause
The column switch (lighting switch) is used to operate the following systems or
functions. If the signal fails, these systems or function will not work normally.
DHeadlamp washer
DHeadlamp, tail lamp
DTurn-signal lamp
DFront fog lamp
DRear foglampDMalfunction of column switch
DMalfunction of ETACS-ECU
NG
Replace the ETACS-ECU.
Ye sCarry out troubleshooting while referring to the Diagnosis Code
Chart on P.54B-9.
Check trouble symptoms.
No
Replace the column switch (lighting switch).
OK
Replace the column switch (wiper and washer switch).
No
Check the column switch (lighting switch and switch body). (Refer
to GROUP 54A - Column Switch.)NG
Replace
Is a diagnosis code output when the ignition switch is at the
OFF (LOCK) position?


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk