check engine MITSUBISHI MONTERO 2000 Service Repair Manual

HEATER, AIR CONDITIONER AND VENTILATION -Troubleshooting 55B-16
Inspection procedure 11
The condenser fan does not operate <4D56>.
Probable cause
If the condenser fan does not operate, the condenser fan relay or motor may be
defective.DMalfunction of the condenser fan relay
DMalfunction of harness or connector
DMalfunction of the engine-A/T-ECU or
engine-ECU
NG
Check the harness wire between the condenser fan relay and
the ignition switch (IG2), and repair if necessary.
NG
Repair
NG
Check the harness wire between the condenser fan motor and
body earth, and repair if necessary.
NG
Repair
NG
Repair
OK
NG
Check the harness wire between the condenser fan relay and
fusible link (1), and repair if necessary.
NG
Repair
NG
Check the harness wires between the condenser fan relay
and the condenser fan motor and between the condenser fan
relay and theengine coolant temperaturesensor, and repair if
necessary.
OK
Check the trouble symptoms.
OK
Check the following connectors:A-10X, A-27, A-04 drive vehicles>, D-143, B-47
OK
Check the trouble symptoms.
OK
Measure at condenser fan motor connector A-27.
DDisconnect the connector and measure at the harness
side.
DContinuity between terminal 2 and body earth
OK:ContinuityNGCheck the following connector:A-27
OK
Check the trouble symptoms.
Check the following connector:A-10X
(2) NG
OK
Check the trouble symptoms.
OK
Measure at condenser fan relay connector A-10X.
DDisconnect the connector, and measure at the J/B side.
DIgnition switch: ON
(1) Voltage between terminal 3 and body earth
OK:System voltage
(2) Voltage between terminal 5 and body earth
OK:System voltage(1) NGCheck the following connectors:A-10X, A-15, D-27, D-210,
D-208
OK
Check the condenser fan motor
(Refer to GROUP 55A - Condenser Fan).NG
Replace
Check the condenser fan relay
(Refer to GROUP 55A - On-vehicle Service).NG
Replace
NG
ReplaceReplace the engine coolant temperaturesensor.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

HEATER, AIR CONDITIONER AND VENTILATION -Troubleshooting 55B-19
Termi-
nal No.Normal condition Check conditions Check item
15Rear defoggerRear defogger: OFFSystem voltage
Rear defogger: ON1.5 V or less
16Multi center display unit communication
lineIgnition switch: ONHi: 4 - 5 V
Lo: 0 - 1 V
17Multi center display unit communication
lineIgnition switch: ONHi: 4 - 5 V
Lo: 0 - 1 V
18Multi center display unit communication
line shieldAt all times0V
19Diagnosis outputIgnition switch: ONA voltmeter needle
fluctuates between 0
and 12 V.
20Input from A/C compressor relayWhen the A/C is off.0V
When the A/C is in operation
(When compressor is operating)System voltage
21Power supply to potentiometerAt all times5V
22Input from outside air temperature
sensorSensor temperature: 25
_C (1.7 kW)1.9 V
23Input from heater water temperature
sensorSensor temperature: 25
_C(5kW)2.8 V
24Input from potentiometer for air mix
damperWhen the damper flap is moving to the
MAX HOT position.0.7 - 1.3 V
25Power supply to illuminationLighting switch: ONSystem voltage
26Power supply to ignition switch (IG2)Ignition switch: ONSystem voltage
27Power supply to ignition switch (ACC)Ignition switch: ACCSystem voltage
28Backup power supplyAt all timesSystem voltage
29Earth to sensor and potentiometerAt all times0V
30Input from air thermo sensorSensor temperature: 25
_C (1.5 kW)2.2 V
31Photo sensor (+)During 800 kcal/m2-h1V
32Input from potentiometer for the air
outlet changeover damperWhen the damper flap is moving to the
DEF position.0.7 - 1.3 V
33Diagnosis inputIgnition switch: ON0V
34Compressor lock signal (ignition signal)Engine speed: 3 000 r/min0.3 - 3.0
35Illumination earthAt all timesContinuity
36EarthAt all timesContinuity
CHECK AT ENGINE-A/T-ECU OR ENGINE-ECU TERMINALS
Refer to GROUP 13A – Troubleshooting or GROUP 13B – Troubleshooting .


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk