automatic transmission MITSUBISHI MONTERO 2000 Service Manual PDF

AUTOMATIC TRANSMISSION -Troubleshooting AUTOMATIC TRANSMISSION -Troubleshooting 23-65
Ter-
minal
No.Standard value Inspection conditions Check item
1062nd solenoid valveEngine: Idling
Shift range: 2ndSystem voltage
Engine: Idling
Shift range: Park7–9 V
107DCC solenoid valveEngine: Idling
Shift range: 1stSystem voltage
108Inhibitor switch REngine: Idling
Selector lever position: RSystem voltage
Engine: Idling
Shift range: Other than the above0V
109Select switchIgnition switch: ON
Selector lever operation: Sports modeSystem voltage
Ignition switch: ON
Selector lever operation: Other than the above0V
11 0Downshift switchIgnition switch: ON
Selector lever operation: Downshifted in Sports mode
and lever heldSystem voltage
Ignition switch: ON
Selector lever operation: Other than the above0V
11 24LLc switchIgnition switch: ON
Transfer lever position: 4LLcSystem voltage
Ignition switch: ON
Transfer lever position: Other than the above0V
11 5Wide open throttle switchAccelerator pedal: ReleasedSystem voltage
Accelerator pedal: Depressed0V
11 73rd shift indicator lampShift range: 3rdSystem voltage
Shift range: Other than the above0V
11 82nd shift indicator lampShift range: 2ndSystem voltage
Shift range: Other than the above0V
11 9RED solenoid valveEngine: Idling
Shift range: 5thSystem voltage
Engine: Idling
Shift range: Park7-9V
120UD solenoid valveEngine: Idling
Shift range: 1stSystem voltage
Engine: Idling
Shift range: Park7-9V
121Inhibitor switch NIgnition switch: ON
Selector lever position: NSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
122Upshift switchIgnition switch: ON
Selector lever operation: Upshifted in Sports mode and
lever heldSystem voltage
Ignition switch: ON
Selector lever operation: Other than the above0V
123Stop lamp switchIgnition switch: ON
Brake pedal DepressedSystem voltage
Ignition switch: ON
Brake pedal Released0V


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-67
Ter-
minal
No.Standard value Inspection conditions Check item
10A/C compressor load signalA/C switch: OFF0V
A/C switch: ONSystem voltage
11Power supplyIgnition switch: OFF0V
Ignition switch: ONSystem voltage
12EarthAt all times0V
13EarthAt all times0V
14OD solenoid valveEngine: Idling
Shift range: 3rdSystem voltage
Engine: Idling
Shift range: Park7-9V
15DCC solenoid valveEngine: Idling
Shift range: 1stSystem voltage
162nd solenoid valveEngine: Idling
Shift range: 2ndSystem voltage
Engine: Idling
Shift range: Park7-9V
172nd shift indicator lampShift range: 2ndSystem voltage
Shift range: Other than the above0V
184th shift indicator lampShift range: 4thSystem voltage
Shift range: Other than the above0V
24Power supplyIgnition switch: OFF0V
Ignition switch: ONSystem voltage
25EarthAt all times0V
26EarthAt all times0V
31Input shaft speed sensorMeasure between terminals (31) and (43) using an
oscilloscope.
Engine: 2 000 r/min
Shift range: 4thCheck Procedure
using an Oscillo-
scope (Refer to
P.23-69.)
32Output shaft speed sensorMeasure between terminals (32) and (43) using an
oscilloscope.
Engine: 2 000 r/min
Shift range: 4thCheck Procedure
using an Oscillo-
scope (Refer to
P.23-69.)
33Engine speed sensorEngine: Idling2.0 - 2.4 V
38Backup power supplyAt all timesSystem voltage
43Sensor earthAt all times0V
44A/T fluid temperature sensorA/T fluid temperature 20°C3.8 - 4.0 V
A/T fluid temperature 40°C3.2 - 3.4 V
A/T fluid temperature 80°C1.7 - 1.9 V
45Accelerator pedal positionAccelerator pedal: Fully closed (engine stopped)0.985 - 1.085 V
sensor (APS)Accelerator pedal: Fully open (engine stopped)4.0 V or higher
51RED solenoid valveEngine: Idling
Shift range: 5thSystem voltage
Engine: Idling
Shift range: Park7-9V
53Output communication withEngine: IdlingOther than 0 V
engine-ECUSelector lever position: D


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-68
Ter-
minal
No.Standard value Inspection conditions Check item
54Input communication withEngine: IdlingOther than 0 V
engine-ECUSelector lever position: D
55Inhibitor switch PIgnition switch: ON
Selector lever position: PSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
56Inhibitor switch NIgnition switch: ON
Selector lever position: NSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
57Select switchIgnition switch: ON
Selector lever operation: Sports modeSystem voltage
Ignition switch: ON
Selector lever operation: Other than the above0V
58Downshift switchIgnition switch: ON
Selector lever position: Downshifted in Sports mode
and lever heldSystem voltage
Ignition switch: ON
Selector lever operation: Other than the above0V
59Stop lamp switchIgnition switch: ON
Brake pedal DepressedSystem voltage
Ignition switch: ON
Brake pedal Released0V
62DIR solenoid valveEngine: Idling
Shift range: ParkSystem voltage
Engine: Idling
Shift range: 2nd7-9V
65Wide open throttle switchAccelerator pedal: Released4.5 - 5.5 V
Accelerator pedal: DepressedLess than 0.4 V
66Inhibitor switch RIgnition switch: ON
Selector lever position: RSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
67Inhibitor switch DIgnition switch: ON
Selector lever position: DSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
68Upshift switchIgnition switch: ON
Selector lever position: Upshifted in Sports mode and
lever heldSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
69Vehicle speed sensorWhen stopped0V
When starting to drive forward slowly.0 V and 5 V alter-
nates
71A/T control relayIgnition switch: OFF0V
Ignition switch: ON10 - 12 V
72EarthIgnition switch: ON0V


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting II>23-71
Diagnosis
codeReference page Diagnosis item
35Freewheel engage switch systemOpen circuit/Short-cir-
cuit/Malfunction of
switch23-83
41Shift actuator (short-circuit/open circuit) systemOpen circuit/Short-cir-
cuit/Malfunction of ac-
tuator/Malfunction of
ECU23-84
42Shift actuator (short-circuit) systemShort-circuit/Malfunc-
tion of actuator/Mal-
function of ECU23-85
43Shift actuator (open circuit) systemOpen circuit/Malfunc-
tion of actuator/Mal-
function of ECU
44Shift actuator (overload) systemMalfunction of transfer
shift mechanism/Mal-
function of actuator23-86
45Tyre problemIncorrect tyre pres-
sure/Uneven tyre sizes23-86
51Malfunction of transfer-ECU23-86


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troublehshooting II>23-72
INSPECTION PROCEDURES CLASSIFIED BY DIAGNOSIS CODE
Code No. 11, 12 Power supply voltage systemProbable cause
Code No. 11 is output to indicate a drop in voltage if the power supply voltage drops
below 9.5 V.
Code No. 12 is output to indicate overvoltage if the power supply voltage rises above
18 V.DMalfunction of ignition switch
DMalfunction of harness or connector
DMalfunction of transfer-ECU
NG OK
OK
Repair NG
Replace
NG
Ignition switch single part check
(Refer to GROUP 54 - Ignition Switch.)
Check the following connectors: D-208,
D-210, D-32, E-115, E-105, D-208, D-210,
E-115, E-105
Repair
Transient malfunction (Refer to GROUP 00 - Points to Note
for Transient Malfunctions.)
Measure at transfer-ECU connector E-105
DMeasure at ECU terminals.
DIgnition switch: ON
DVoltage between terminal 13 and earth
OK:System voltage
Check the harness between the ignition switch and the
transfer-ECU, and repair if necessary.
OK
Replace the transfer-ECU. OKOK NG
NGCheck the trouble symptoms.
MUT-
IIData List
DNo. 9 Ignition voltage
OK:Refer to P.23-87 (Data List Chart).
NG
Check the following connector:E-105
Code No. 13 Main relay (inside ECU) systemProbable cause
Code No. 13 is output to indicate a relay malfunction if the voltage rises to 6 V
or higher when the relay is off, or if it drops below 6 V when the relay is on.DMalfunction of transfer-ECU
Replace the transfer-ECU.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troublehshooting II>23-73
Code No. 21 Accelerator pedal position sensor (APS)
systemProbable cause
Code No. 21 is output to indicate anopencircuit in the APS or an incorrect
adjustment when the APS output voltage drops below 0.2 V while theengine is
idling.DMalfunction of APS
DMalfunction of harness or connector
DMalfunction of transfer-ECU
DMalfunction of throttle valve controller <6G7>
DMalfunction of engine-ECU <4M4>
NGNG
NG
Repair
MUT-
IIData List
DNo. 1 APS
OK:Refer to P.23-87 (Data List
Chart).
NG
ReplaceAPS single part check
(Refer to GROUP 13 - On-vehicle
Service.)
OK
NG
Repair
OK
Check the following connector:
D-135
OK
DCheck the harness between the
APS and the throttle valve
controller, and repair if necessary.
<6G7>
DCheck the harness between the
APS and the engine-ECU, and
repair if necessary.<4M4> OK
Check the following connectors:
<6G7> D-11,<4M4> D-112
Repair
NG
Repair
NG
Repair
OK
DCheck the harness between the
APS and the throttle valve
controller. <6G7>
DCheck the harness between the
APS and the engine-ECU. <4M4>
OK
Check the following connectors:
<6G7> D-11,<4M4> D-112
Measure at throttle valve controller
connector D-11 <6G7>, or at
engine-ECU connector D-112 <4M4>.
DMeasure at ECU terminals.
DIgnition switch: ON
D<6G7> Voltage between terminal
6 and earth
D<4M4> Voltage between terminal
60 and earth
OK:4.8 - 5.2 V
NGNG
NGCheck the trouble symptoms.Replace the throttle valve controller
or the engine-ECU.
OK
Measure at APS connector D-135
DDisconnect the connector and
measure at the harness side.
DVoltage between terminal 8 and
earth
(Ignition switch: ON)
OK:4.8 - 5.2 V
To the nextpage
Transient malfunction
(Refer to GROUP 00 - Points to
Note for Transient Malfunctions.)
OK


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troublehshooting II>23-74
OKOK OK
NG
NG
NG(1)NGCheck the following connectors:
<6G7> D-11,<4M4> D-112
Repair OK
DCheck the harness between the
APS and the throttle valve
controller, and repair if necessary.
<6G7>
DCheck the harness between the
APS and the engine-ECU, and
repair if necessary.<4M4> OK (2)NG
Measure at transfer-ECU connector
E-105
DMeasure at ECU terminals.
DIgnition switch: ON
DVoltage between terminal 13 and
earth
OK:Fully close the accelerator
985 - 1,085 mV
fullyopen the accelerator
4,000 mV or more
Check the following connector:E-105
Check the trouble symptoms.OK
Check the following connectors:
E-105, E-113 NG
Replace the transfer-ECU. OK
NGRepair
Check the harness between the APS
and the transfer-ECU, and repair if
necessary.
Check the harness between the APS
and the transfer-ECU, and repair if
necessary.
From the previouspage
(3)NG
Measure at APS connector D-135.
DUse the test harness
(MB991658) to connect only
terminals 6, 7 and 8, and
measure at the pickup harness.
DIgnition switch: ON
(1) Voltage between terminal 7 and
earth
OK:0.5 V or less
(2) Voltage between terminal 8 and
earth
OK:4.8 - 5.2 V
(3) Voltage between terminal 6 and
earth
OK:Fully close the accelerator
985 - 1,085 mV
fullyopen the accelerator
4,000 mV or more
APS adjustment
(Refer to GROUP 13 - On-vehicle
Service.)
Check the following connectors:
E-113, E-105
Repair


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troublehshooting II>23-75
Code No. 22, 23 Front propeller shaft speed sensor
systemProbable cause
Code No. 22 is output to indicate anopencircuit or short-circuit in the front
propeller shaft speed sensor if no signal is input from the front propeller shaft
speed sensor when shifting from 2WD to 4WD while driving atmedium to low
speeds.
Code No. 23 is output to indicate anopencircuit or short-circuit in the front
propeller shaft speed sensor if the signal input from the front propeller shaft
speed sensor is unstable when the freewheelengageswitch is on.DMalfunction of front propeller shaft speed sensor
DMalfunction of harness or connector
DMalfunction of transfer-ECU
Transient malfunction (Refer to GROUP 00 - Points to Note
for Transient Malfunctions.)
OK NG
OK
OK
To the nextpage
NG
OK
NG
NG
Repair
Replace the transfer-ECU.
OKMUT-
IIData List
DNo. 2 Front propeller shaft speed sensor
OK:Refer to P.23-87 (Data List Chart).
OK
OK
NG
OK
Measure at transfer-ECU connector E-105
DMeasure at ECU terminals.
DIgnition switch: ON
DVoltage between terminals 18 and earth
OK:0.5 V or less
NG
Repair
Replace the transfer-ECU.
NG
Check the trouble symptoms.
Check the trouble symptoms.
Replace the transfer-ECU.
OK
OK
Measure at transfer-ECU connector E-105
DMeasure at ECU terminals.
DDisconnect front propeller shaft speed sensor connector
C-17.
DIgnition switch: ON
DVoltage between terminals 7 and earth
OK:4.8 - 5.2 V
Measure the front propeller shaft speed sensor output wave
pattern at transfer-ECU connector E-105 (using an
oscilloscope).
DVehicle speed: approx. 50 km/h
DShift range: 3rd
DVoltage between terminals 7 - 18
OK:A wave pattern such as the one shown on P.23-69
(Check Procedure Using an Oscilloscope tern B>) should be output, and the maximum value
should be 4.8 V or more and the minimumvalue
should be 0.8 V or less.
There should be no noise in the output wave pattern.
NG
RepairCheck the following connectors:C-17, E-105NG
NG
Repair
Check the following connector:E-105Repair
NG
Check the harness between the front propeller shaft speed
sensor and the transfer-ECU.
Check the following connector:C-17
Check the trouble symptoms.
Check the following connector:E-105


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troublehshooting II>23-76
(2)NG
(3)NG
From the previouspage
(1)NG
OK
NG
Measure at front propeller shaft speed sensor connector C-17.
DDisconnect the connector and measure at the harness
side.
(1) Resistance between terminal 1 and earth
OK:2
Wor less
(2) Voltage between terminal 2 and earth
(Ignition switch: ON)
OK:4.8 - 5.2 V
(3) Voltage between terminal 3 and earth
(Ignition switch: ON)
OK:System voltage
Check the harness between the front propeller shaft speed
sensor and the ignition switch, and repair if necessary.
Check the following connectors:D-208, D-213, D-32, E-115
NG
Check the trouble symptoms.
Check the harness between the front propeller shaft speed
sensor and the transfer-ECU, and repair if necessary. (Earth
line)
Replace the front propeller shaft speed sensorOK
OK
Repair
Check the harness between the front propeller shaft speed
sensor and the transfer-ECU, and repair if necessary. (Sensor
line)
Eliminate the cause of the noise.
NG
Check the trouble symptoms.
NG
Repair
OK
NG
Repair
OK
DCheck the harness between the front propeller shaft speed
sensor and the transfer-ECU.
DCheck the harness between the front propeller shaft speed
sensor and the ignition switch.
Check the following connectors:D-208, D-213, D-32, E-115,
E-105


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troublehshooting II>23-77
Code No. 24, 25 Rear propeller shaft speed sensor systemProbable cause
Code No. 24 is output to indicate anopencircuit or short-circuit in the rear
propeller shaft speed sensor if the signal input from the rear propeller shaft
speed sensor is unstable when the APS voltage is 1.5 V or higher.
Code No. 25 is output to indicate anopencircuit or short-circuit in the rear
propeller shaft speed sensor if the signal input from the rear propeller shaft
speed sensor is unstable when the freewheelengageswitch is on.DNo. 3 Rear propeller shaft speed sensor
DMalfunction of harness or connector
DMalfunction of transfer-ECU
Transient malfunction (Refer to GROUP 00 - Points to Note
for Transient Malfunctions.)
OK NG
Check the following connector:E-105
OK
OK
To the nextpage
NG
OK
NG
NG
Repair
Check the following connector:C-08
Replace the transfer-ECU.
OKMUT-
IIData List
DNo. 3 Rear propeller shaft speed sensor
OK:Refer to P.23-87 (Data List Chart).
OK
OK
NG
Check the trouble symptoms.
OK
Measure at transfer-ECU connector E-105
DMeasure at ECU terminals.
DIgnition switch: ON
DVoltage between terminals 18 and earth
OK:0.5 V or less
NG
Repair
Replace the transfer-ECU.
NG
Check the trouble symptoms.
Check the trouble symptoms.
Replace the transfer-ECU.
OK
OK
Measure at transfer-ECU connector E-105
DMeasure at ECU terminals.
DDisconnect rear propeller shaft speed sensor connector
C-08.
DIgnition switch: ON
DVoltage between terminals 9 and earth
OK:4.8 - 5.2 V
Measure the rear propeller shaft speed sensor output wave
pattern at transfer-ECU connector E-105 (using an
oscilloscope).
DVehicle speed: approx. 50 km/h
DShift range: 3rd
DVoltage between terminals 9 - 18
OK:A wave pattern such as the one shown on P.23-69
(Check Procedure Using an Oscilloscope) should be
output, and the maximum value should be 4.8 V or
more and the minimumvalue should be 0.8 V or
less.
There should be no noise in the output wave pattern.
NG
RepairCheck the following connectors:C-08, E-108NG
NG
Repair
Check the following connector:E-108Repair
NG
Check the harness between the rear propeller shaft speed
sensor and the transfer-ECU.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk