instrument cluster MITSUBISHI OUTLANDER 2019 Owner's Manual (in English)

Instruments and controls 1-1
1
Overview
N00100202847
Instruments and controls
Combination headlights an
d dimmer switch P.5-209
Automatic high beam system switch (if so equipped) P.5-213 Turn signal lever P.5-219 Front fog light switc
h (if so equipped)
P.5-220
Steering wheel remote control switches [Refer to the separate owner’s manual.]
Active stability control (ASC) OFF switch P.5-100
Supplemental restraint system (SRS) - airbag (for driver’s seat) P.4-35, 4-42 Horn switch P.5-229
Instrument cluster P.5-155
Windshield wiper and washer switch P.5-221 Rear window wiper and washer switch P.5-225
Cruise control switches P.5-102, 5-106
Steering wheel height and reach adjustment lever P.5-57
Engine switch (if so equipped) P.5-17
Driver’s vents P. 7 - 2
Sportronic steering wheel paddle shifter (if so equipped) P.5-71, 5-79
Driver’s vents P.7-2
Multi information display switch (if so equipped) P.5-159
Headlight leveling switch (if so equipped) P.5-218
Driver’s side power liftgate switch (if so equipped) P.5-40
Fuses P.9-27
Lane Departure Warning (LDW) switch (if so equipped)P.5-136 Forward Collision Mitigation system (FCM) ON/OFF switch (if so equipped)P.5-121
Supplemental restraint system (SRS) - front knee airbag (for driver’s seat) P.4-35, 4-42
Ignition switch (if so equipped) P.5-63
Camera switch (if so equipped) P. 5-146
BK0264300US.book 1 ページ ２０１８年２月２８日　水曜日　午後５時１６分

If this warning light comes on or flashes while you’re driving... 2-2 Quick index
2
Electric parking brake warning light
(yellow) (if so equipped)
 If the warning light comes on during driving,
there is the possibility that the parking
brake cannot be operated or released. Immedi
ately stop the vehicle
in a safe place,
and contact an authorized Mi
tsubishi Motors dealer or a repair facility of your
choice for assistance.
P. 5-205
Selector lever position indicator in the instrument cluster bl
inks rapidly (once
per second)
(Vehicles equipped with mono-color
liquid crystal display)
 Park your vehicle in a safe place. Idle the engine until the selector
lever position indica
tor stops blinking.
If the indicator continues bl
inking, contact an authorized
Mitsubishi Motors dealer
or a repair facility of
your choice immediately.
P. 5-69, 5-77
or
Engine malfunction indicator (“SERVICE ENGINE SOON” or
“Check engine light”)
 Although your vehicle will usually be dr
ivable and not need towing, have the
engine system checked at an authorized Mi
tsubishi Motors dealer
or a repair facility
of your choice as soon as possible. If the
vehicle is not drivab
le, contact emergency
roadside assistance at 1-888-648-7820 (for
vehicles sold in U.S.A.) or 1-888-576-
4878 (for vehicles sold in Canada), an aut
horized Mitsubishi Moto
rs dealer, or local
towing company for assistance.
P. 5-206
Warning lights
Do this
Ref. Page
BK0264300US.book 2 ページ ２０１８年２月２８日　水曜日　午後５時１６分

If this warning light comes on or
flashes while you’re driving...
Quick index 2-3
2
Electric power stee
ring system (EPS)
warning light
(Vehicles equipped with mono-color
liquid crystal display)
 If this light comes on while the engine is r
unning, it may become harder to turn the
steering wheel. Have your ve
hicle inspected at an authorized Mitsubishi Motors
dealer or a repair facility of
your choice as soon as possible.
P. 5-98
Anti-lock braking system warning
light
 When this light comes on,
the anti-lock braking system
is not functioning and only
the ordinary braking system is functioning. Park your vehicle in a safe
place and stop the engine.
Test the system as described on page 5-97.  If the light does not go out after the test, or
if it comes on again, we recommend that
you have the system checked at an authorized
Mitsubishi Motors dealer or a repair
facility of your choice
as soon as possible.
P. 5-97
SRS warning light
 Immediately have the airbag and the pre-te
nsioner seat belt sy
stem checked at an
authorized Mitsubishi Motors dealer.
P. 4-41
Selector lever position indicator in the instrument cluster bl
inks slowly (once
every 2 seconds)
(Vehicles equipped with mono-color
liquid crystal display)
 Have the automatic transaxle checked at an
authorized Mitsubishi Motors dealer or
a repair facility of your
choice immediately.
P. 5-69, 5-77
Wa rn in g l ig h t s
Do this
Ref. Page
BK0264300US.book 3 ページ ２０１８年２月２８日　水曜日　午後５時１６分

5
Features and controlsBreak-in recommendations ..............................................................5-3 Keys .................................................................................................5-3 Electronic immobilizer (Anti-theft starting system) ........................5-4Keyless entry system (if so equipped) ..............................................5-7 Free-hand Advanced Security
Transmitter (F.A.S.T.-key)
(if so equipped) ..........................................................................5-12Door locks ......................................................................................5-33 Power door locks ......
...........
...........
...........
...........
...........
.........
.....5-35
Child safety locks for rear door ..........
...........
.........
.........
.........
.....5-36
Liftgate (except for vehi
cles equipped with the
power liftgate) ....5-37
Power liftgate (if so equipped) .......................................................5-38 Inside liftgate release .....................................................................5-45Theft-alarm system ........................................................................5-45 Power window control ...................................................................5-48 Sunroof (if so equipped) .................................................................5-51Parking brake .................................................................................5-53 Steering wheel height and reach adjustment ..................................5-57 Inside rearview mirror ...................................................................5-57Outside rearview mirrors ...............................................................5-60 Ignition switch (if so equipped) ......................................................5-63 Steering wheel lock (if so equipped) ..............................................5-65Starting the engine .........................................................................5-65 Automatic transaxle (if so equipped)..............................................5-67 Continuously variable transmission
(CVT) (if so equipped)..........5-74
Electronically controlled
4WD system (if so equipped).................5-82
S-AWC (Super-All Wheel Control) (if
so equipped) .....................5-84
4-wheel drive operation .................................................................5-87Inspection and maintenance followi
ng rough road operation ........5-90
Cautions on the handling of 4-wheel dr
ive vehicles ..................... 5-90
Service brake ................................................................................. 5-91 Brake auto hold (if so equipped) .................................................... 5-92Hill start assist (if so equipped) ...................................................... 5-94 Brake assist system ........................................................................ 5-95 Anti-lock braking system .............................................................. 5-96Electric power steering system (EPS) ........................................... 5-98 Active stability control (ASC) ....................................................... 5-99 Cruise control (if so equipped) ..................................................... 5-102Adaptive Cruise Control System (ACC)
(if so equipped) ............ 5-106
Forward Collision Mitigation System
(FCM) (if so equipped) .... 5-117
Blind Spot Warning (BSW) (w
ith Lane Change Assist)
(if so equipped) ........................................................................ 5-126 Rear Cross Traffic Alert (RCTA) (if so equipped) ....................... 5-132 Lane Departure Warning System (LDW
) (if so equipped)........... 5-136
Tire pressure monitoring system ................................................. 5-139 Rear-view camera (if so equipped)............................................... 5-144 Multi Around Monitor (if so
equipped)..................
...........
........... 5-146
Instrument cluster ........................................................................ 5-155 Multi Information display - Type 1 ............................................. 5-156 Multi Information display - Type 2 ............................................. 5-175Indicator light, warning light, and information screen display list (multi informati
on display - Type 1) .......... 5-183
Indicator and warning light package (multi information display - Type 2) ....................................... 5-203 Indicators ..................................................................................... 5-204 Warning lights .............................................................................. 5-205
BK0264300US.book 1 ページ ２０１８年２月２８日　水曜日　午後５時１６分

Parking brake 5-54 Features and controls
5
N00593200050
The Electric parking brake is the system that applies the parking brake by the electricmotor.
When the parking brake is applied, the brake warning light (red) in the instrument clusterand the indicator light (A) on the Electric parking brake switch will come on. When parking on a hill, set the parking brake, and turn the front wheels toward the curb on adownhill, or away from
the curb on an uphill.
CAUTIONBefore driving, be sure that the parking brake is fully released and brake warninglight is off.If you drive without the parking brake fully released, the warning
display will appear on
the information screen in the multi-informa-tion display. If a vehicle is driven without releasing the parking brake, the brakes will be overheated,resulting in ineffectiv
e braking and possible
brake failure. Warning light (red)
or
Warning display
Electric parking brake
(if so
equipped)
NOTE
 You may hear an operation noise from the vehicle body when operating the Electricparking brake. This do
es not indicate a mal-
function and the Elec
tric parking brake is
operating normally.  When the battery is weak or dead, the Elec- tric parking brake
cannot be applied or
released. Refer to “Jum
p-starting the engine”
on page 8-2.  You may feel the brake pedal moving when operating the Electr
ic parking brake.
This does not indi
cate a malfunction.
To apply

1. Stop the vehicle completely. 2. Pull up the Electric parking brake switch
while depressing the brake pedal.
CAUTION While the vehicle is in
motion, do not apply
the Electric parking
brake. Doing so may
cause overheating and/or
premature wear of
brake parts, reducing brake performance. NOTE
 In the following conditions, the brake warn- ing light (red) will il
luminate for approxi-
mately 15 seconds and then go off. • While the Electric pa
rking brake is applied,
the ignition switch is turned to the “OFF” position or the opera
tion mode is put in
OFF. • While the ignition switch is in the “OFF” position or the operation mode is in OFF,the Electric pa
rking brake switch is pulled
up.
BK0264300US.book 54 ページ ２０１８年２月２８日　水曜日　午後５時１６分

Brake auto hold (if so equipped)
Features and controls 5-93
5
When the vehicle is
stopped by depressing
the brake pedal with the selector lever in any position other than “P” (PARK) or “R”(REVERSE), the brake auto hold activates and the vehicle will be
held stationary.
The brake auto hold indicator light in theinstrument cluster will come on while the system activates.
• If this warning appear
s, confirm that all of
the conditions for system operation are metand that there is no malfunction in the sys-tem. • If this warning appears, fasten the driver’s seat belt.
 If any of the following occur while the sys- tem is standby state, the brake auto hold sys-tem will be turned off automatically and the indicator light on the switch goes off. A buzzer will sound a
nd the message will
appear on the information screen in the multi information display. • When the driver’s seat
belt is unfastened.
• When the driver’s door is opened.• When there is a malfunction in the systemNOTE
 If keeping pressing the brake auto hold switch after setting
the brake auto hold to
ON (stand by), the brake auto hold willreturn to OFF as a protection function is operated. After returning to OFF, the brake auto holdwill not be switched to
ON (Stand by) even if
the brake auto hold switch is pressed. To set the brake auto hold to
ON, restart the engine
and press the brake auto hold switch again.
To activate brake auto hold

NOTE
or
CAUTION Release the brake pedal only after the brake auto hold indicator li
ght has illuminated.
NOTE
In the following situations, the brake auto hold system may not
operate temporarily.
• The vehicle is stoppe
d on a slippery road.
• The vehicle was stoppe
d while the steering
wheel was turned all the way to the left or right. • The vehicle is being turned on a parking lot turntable. If this occurs, the brake auto hold system will return to the normal operation if youdepress the accelerator
pedal and the vehicle
starts moving again.  If the following operation is performed, the brake auto hold will be deactivated and the brake auto hold indicator light in the instru-ment cluster goes off. • When shifting the selector lever to the “P” (PARK) or “R” (REVERSE) position with depressing the brake pedal. • When the Electric park
ing brake is applied
by using the Electric
parking brake switch.
BK0264300US.book 93 ページ ２０１８年２月２８日　水曜日　午後５時１６分

Hill start assist (if so equipped) 5-94 Features and controls
5
Depress the acceleration
pedal with the selec-
tor lever in any position other than “P” (PARK) or “N” (NEUTRAL).The brakes are released, and the brake auto hold indicator light in the instrument cluster will go off.
Press the brake auto hold switch to turn off the brake auto hold. The indicator light on the switch goes off. If you want to turn off the system while thebrake auto hold indicator light is illuminated, press the switch with
depressing the brake
pedal.
N00562601097
The hill start assist makes it easy to start off on a steep uphill slope by preventing the vehicle from moving backwards. It keeps thebraking force for about 2 second when you move your foot from the brake pedal to the accelerator pedal.
 While the vehicle is held
stationary with the
brake auto hold system, the Electric parkingbrake will be automati
cally applied under the
following conditions
, and a buzzer will
sound and the message
will appear on the
information screen in the multi informationdisplay. • After approximately 10 minutes has elapsed with applying the brake auto hold system. • When the driver’s seat
belt is unfastened.
• When the driver’s door is opened. • When the ignition switch is turned to the “OFF” position or the operation mode is put in OFF. • When the system detect
s the vehicle sliding
down a slope. If the Electric park
ing brake cannot be
applied automatically due to the system mal- function, the message will appear on the information screen in the multi informationdisplay. Depress the brake pedal.NOTE
 If the ignition switch is turned to the “OFF” position or the operation mode is put in OFFwith the selector leve
r in any position other
than “P” (PARK) posit
ion, the message may
appear on the information screen in the multi information display.If the message appears, shift the selector lever to the “P” (PARK) position while depressing the brake pedal.
To start the vehicle

NOTE
To turn off brake auto hold

NOTE
 If the brake auto hold system is turned off without the brake peda
l being depressed, a
buzzer will sound and the message will appear on the information screen in the multiinformation display.
Hill start assist
(if so equipped)
BK0264300US.book 94 ページ ２０１８年２月２８日　水曜日　午後５時１６分

Blind Spot Warning (BSW) (with Lane Change Assist) (if so equipped) 5-128 Features and controls
5
N00593500079
When the BSW switch is pressed while the operation mode is ON,
the BSW indicator
light in the instrument cluster comes on andthe BSW becomes in stand by state. When the BSW switch is pressed again, the BSW indi- cator light in the instrument cluster goes offand the BSW turns off. Indicator light If you turn the BSW ON/OFF, the Rear Cross Traffic Alert (RCTA) also turns ON/OFF atthe same time.
When the BSW indicator light in the instru- ment cluster is on, if
a vehicle is approaching
your vehicle in the dete
ction area, the Blind
Spot Warning light in the outside rearview mirror illuminates.If the turn signal lever is operated to the side where the Blind Spot Warning light is illumi- nated, the Blind Spot Warning light will blink and the system will beep three times to alert the driver.
To operate

NOTE
 When the operation mode is set to OFF, the selected condition just
before setting to OFF
is retained.  The BSW operates when all of the following conditions are met. • The operation mode is put in ON. • The selector lever is
in positions other than
“P” (PARK) and “R” (REVERSE). • The speed of your ve
hicle is approximately
6 mph (10km/h) or higher.
When the sensor detects an approaching vehicle

NOTE
 The Blind Spot Warni
ng light in the outside
rearview mirror may come
on or blink in the
following conditions. • When driving very near the guardrail or the concrete wall.
BK0264300US.book 128 ページ ２０１８年２月２８日　水曜日　午後５時１６分

Instrument cluster
Features and controls 5-155
5
N00519001402
N00519101272
The speedometer shows the vehicle speed in miles per hour (mph) or kilometers per hour(km/h).
• An object having a height from the road surface may seem to appear from the jointof the view com
position processing
regions.
 The brightness of the views from each cam- era may vary dependi
ng on the illuminance
conditions.  An object above the came
ra is not displayed.
 The object displayed in the Front-view mode or the Rear-view mode may not be displayed in the Bird’s eye-view mode.  The view in the Bird’s eye-view mode may be displaced from its true position when the mounting location and a
ngle of each camera
are changed.  The lines on the road may appear to be dis- placed or bent at th
e joint of the views.
NOTE
Instrument cluster 1- Tachometer
 P.5-156
Type 1 Type 2
2- Multi Information display (Type
1:Color liquid crystal display type)  P.5-156 Information screen display list (Type 1)  P.5-184 Multi Information display (Type2:Mono-color liquid crystal display type)
 P.5-175
3- Speedometer
P.5-155
4- Rheostat illumination button (Type 1)
 P.5-156
5- Multi information display switch (Type
2)  P.5-176
Speedometer Type A
BK0264300US.book 155 ページ ２０１８年２月２８日　水曜日　午後５時１６分

Information screen display (Vehicle equipped with the multi information display - Type 1) 5-208 Features and controls
5
N00590300034
This light comes on when the washer fluid is running low.If the light comes on, replenish the container with washer fluid. Refer to “Washer fl
uid” on page 9-13.
Refer to “Capacity” on page 11-7.
N00558301064 N00558401179
This warning is displayed if the vehicle is being driven with the parking brake stillapplied. The warning light in the instrument cluster only comes on when the parking brake is applied.
When the ignition switch is turned to the “ON” position or the ope
ration mode is put in
ON, if the brake fluid is
low, this warning is
displayed. The warning light in the instrument cluster also illuminates.
NOTE
 When the interior light auto-cutout function is been activated, the light goes out automat-ically after about 30 minutes.Refer to “Interior light
auto-cutout function
(dome light and other
lights)” on page 5-241.
Washer fluid level warning light (Vehicle e
quipped with the
multi information display - Type 2)
Information screen display (Vehicle equipped with the multi information display - Type 1) Brake warning display
CAUTION If a vehicle is driven without releasing the parking brake, the brakes will overheat, resulting in ineffective braking and possiblebrake failure. If this warning is displayed, release the park- ing brake.
CAUTION If this warning stays on and does not go out while driving, there is
a danger of ineffective
braking. If this happens
, park the vehicle in a
safe place, and contac
t an authorized Mit-
subishi Motors dealer or a repair facility ofyour choice. If the brake warning display, brake warning light, and the Anti-lock braking system warning light are illu
minated at the same
time, the braking forc
e distribution function
will not operate, so th
e vehicle may be desta-
bilized during sudden br
aking. Avoid sudden
braking and high-speed driving. Park thevehicle in a safe place,
and contact an autho-
rized Mitsubishi Motors
dealer or a repair
facility of your choice. The vehicle should be brought to a halt in the following manner when
brake performance
is deteriorated.
BK0264300US.book 208 ページ ２０１８年２月２８日　水曜日　午後５時１６分