MITSUBISHI OUTLANDER 2020 (in English) Owners Manual
Manufacturer: MITSUBISHI, Model Year: 2020, Model line: OUTLANDER, Model: MITSUBISHI OUTLANDER 2020Pages: 443, PDF Size: 60.03 MB
Page 91 of 443

Keyless entry system (if so equipped) 5-10 Features and controls
5
2. Using a valid (already registered) remote control transmitter, ac 
tivate the registra- 
tion mode according to the following steps. Steps ii to iv should be completed within 8 seconds. 
3. Within 60 seconds after step 2, complete the following ID code 
 registration opera- 
tion using the next remote control trans- mitter you wish to register within 4 seconds. 4. To register the ID 
 codes of additional 
remote control transmitters, repeat step 3 within 60 seconds after step 3.5. If no ID code of a remote control trans- mitter is registered within 60 seconds after step 3, the regi 
stration mode is can- 
celed and the normal mode returns. 
i) Press and hold the  
UNLOCK button (2)  for 4 to 8 seconds. 
ii) While holding the  
UNLOCK button (2),  press the LOCK but-ton (1). 
iii) While holding the  
UNLOCK button (2), release the LOCK but- ton (1). 
iv) 
Release the UNLOCK  button (2).NOTE
 ID codes for all remote control transmitters except for the transmitter used in steps 2 are erased and the answerback function (door is locked and unlocked) informs you that theregistration mode ha 
s been activated.
i) Press both the LOCK  
and UNLOCK but- tons for 2 seconds. 
ii) Release both the  
LOCK and UNLOCK  buttons for 1 second. 
iii) 
Press the UNLOCK  button.NOTE
 Be sure to press the buttons correctly when performing the procedures. If you perform the procedures incorrectly, the registered ID code information could  
be deleted or the set- 
tings could be changed  
unintentionally. If the 
registered ID code in 
formation is deleted, 
register the remote control transmittersagain.
 For verification purposes, try to lock and unlock the doors after the registration iscompleted.  The indicator light (4) comes on each time a button is pressed.  The keyless entry system does not work if the key is in the ignition switch.  The remote control transmitter can be used from approximately 40  
feet (12 m) away. 
However, this distance 
 may change if your 
vehicle is near a TV  
transmitting tower, a 
power station, or 
 a radio station. 
 If the following conditi
ons are observed after 
pressing the LOCK (1) or UNLOCK (2) but-ton on the remote control transmitter, the battery in the remote control transmitter may need to be replaced. • The doors and the lift 
gate cannot be locked 
or unlocked. • The panic alarm  
cannot be operated. 
• The indicator light  
(4) is dim or does not 
come on. 
 If you lose your remote control transmitter, please contact an au 
thorized Mitsubishi 
Motors dealer for a replacement.  If you wish to obtain 
an additional remote 
control transmitter, please contact an autho-rized Mitsubishi Moto 
rs dealer. A maximum 
of 8 remote control tr 
ansmitters can be pro- 
grammed for your vehicle.NOTE
BK0278200US.book  10 ページ  2019年4月10日 水曜日 午前10時59分 
Page 92 of 443

Keyless entry system (if so equipped) 
Features and controls 5-11
5
 To use the new remote control transmitters, it is necessary to register the key with both theelectronic immobilizer  
and keyless entry sys- 
tem. Also refer to “Electr 
onic immobilizer (Anti- 
theft starting system): Customer key pro-gramming” on page 5-6.NOTE
BK0278200US.book  11 ページ  2019年4月10日 水曜日 午前10時59分 
Page 93 of 443

Keyless entry system (if so equipped) 5-12 Features and controls
5
N00596500041
You can change the settings for the follow 
ing functions according to your preferences.
 When changing a setting, perform the fol
lowing steps. 
1. Remove the key from  
the ignition switch. 
2. Open the driver’s door and turn the combination  
headlights and dimmer switc
h to the “OFF” position. 
3. Complete steps i to iv of the procedure. Step 
s ii to iv should be completed within 8 seconds.
Customizing the keyless entry system
 
Item
Ste p i
Ste p i i
Step iii
Ste p i v
Notification
Horn deactiva- tion/reactivation 
Press and hold the  LOCK button (1) for 4 to 8 seconds. 
While holding the  LOCK button (1), press the UNLOCK button (2). 
While holding the  LOCK button (1), release the UNLOCK  button (2). 
Release the LOCK but- ton (1). 
Chimes   Page 5-8
Turn signal lights  deactivation/reac- tivation 
Press and hold the  UNLOCK button (2) for  4 to 8 seconds. 
While holding the  UNLOCK button (2),  press the LOCK button  (1). 
While holding the  LOCK button (1),  release the UNLOCK  button (2). 
Release the LOCK but- ton (1). 
Chimes   Page 5-8
Setting the door  and liftgate unlock  function 
Press and hold the  LOCK button (1) for 4 to 8 seconds. 
While holding the  LOCK button (1), press the UNLOCK button (2). 
While holding the  UNLOCK button (2), release the LOCK button  (1). 
Release the UNLOCK  button (2). 
Chimes   Page 5-8
BK0278200US.book  12 ページ  2019年4月10日 水曜日 午前10時59分 
Page 94 of 443

Keyless entry system (if so equipped) 
Features and controls 5-13
5
N00546101124
Your keyless entry system operates on a radio frequency subject to 
 Federal Communica- 
tions Commission (FCC)  
Rules (For vehicles 
sold in U.S.A.) and Industry Canada Rules (For vehicles sold in Canada). This device complies with Part 15 of FCC Rules andIndustry Canada licenc 
e-exempt RSS stan- 
dard(s). Operation is subject to the following two con-ditions.  This device may not 
cause harmful inter- 
ference.  This device must ac
cept any interference 
received, including interference that may cause undesired operation.
N00544101247
1. Before replacing the battery, remove staticelectricity from your body by touching a metal grounded object.
NOTE
 Be sure to press the buttons correctly wh
en performing the procedures. If you perform 
the procedures incorrectly, the registere
d ID code information could 
be deleted or the settings 
 could be changed uninten
tionally. If the registered ID code info
rmation is deleted, register the rem
ote control transmitters again. 
Refer to “Customer remote control tr 
ansmitter programming (Except for vehicl
es sold in Canada)” on page 5-9.
General information
 
CAUTIONChanges or modifica
tions not expressly 
approved by the manufacturer for compli- ance could void the user’s authority to oper-ate the equipment.
Procedure for replacing the  remote control transmitter bat-tery
 WA R N I N G Do not swallow a coin type battery.• This product contains coin type battery. If a coin type battery is swallowed, it can cause severe internal burns and can lead to death.There have been case 
s where a swallowed 
battery has caused severe internal burns in just 2 hours.• Keep new and used batteries away fromchildren.• If the remote control transmitter casedoes not close securely, stop using theproduct and keep it away from children.• If you think batter 
ies might have been 
swallowed or placed in 
side any part of a 
person’s body, seek immediate medical attention.
 To prevent that can result in an explosion or the leakage of fl 
ammable liquid or gas.
• Do not replace an 
incorrectly battery. 
Replace only with th 
e same or equivalent 
type.• Do not dispose of a battery into fire orincinerator, or mech 
anically crushing or 
cutting of a battery.• Do not use, store in or bring into a bat-tery where it may be exposed to extremely high temperature or extremelylow air pressure.CAUTION When the remote control transmitter case is opened, be careful to keep water, dust, etc.out. Also, do not touch the internal compo- nents. Dispose of used battery according to regula- tions for the disposal of battery.WA R N I N G
BK0278200US.book  13 ページ  2019年4月10日 水曜日 午前10時59分 
Page 95 of 443

Keyless entry system (if so equipped) 5-14 Features and controls
5
2. Remove the screw (A) from the remote control transmitter. 3. With the Mitsubishi mark facing you, insert the cloth-cov-ered tip of a flat blade screwdriver into the notch in the remote control transmitter case and use it to openthe case. 
4. Remove the used battery. 
5. Install a new battery with the +side (B) up. 6. Close the remote control transmitter case firmly. 7. Attach the screw (A) removed in step 2. 8. Check the keyless entry system to see thatit works.
NOTE
 Be sure to perform the procedure with the Mitsubishi mark facing you. If the Mitsubi-shi mark is not facing you when you open theremote control transmitter case, the buttons may come out.  The Federal Communications Commission (FCC) ID number, the Industry Canada (IC) number and the model  
number (radio certifi- 
cation) are indicated in 
 the illustrated posi- 
tion.
NOTE
 You may purchase a replacement battery at an electric appliance store.  An authorized Mitsubishi Motors dealer can replace the battery for you if you prefer.
+ side - side Coin type bat- tery CR1620
BK0278200US.book  14 ページ  2019年4月10日 水曜日 午前10時59分 
Page 96 of 443

Free-hand Advanced Securi
ty Transmitter (F.A.S.T.-key) (if so equipped) 
Features and controls 5-15
5
N00503101222
The Free-hand Advanced Security Transmit- ter (F.A.S.T.-key) enables the doors and theliftgate to be locked  
and unlocked, the engine 
to be started and the operation mode to be changed simply by carrying it. The F.A.S.T.-key can also be used as the remote control transmitter of the keylessentry system. Refer to “Free-hand  
Advanced Security 
Transmitter (F.A.S.T.-key): Keyless entrysystem” on page 5-31. 
The operations possible with the F.A.S.T.- key can be modified as stated below. (Keyless entry operations are possible.) For details, contact an 
 authorized Mitsubi- 
shi Motors dealer. • Enabling only the locking and unlocking of the doors and the liftgate• Enabling only the starting of the engine • Deactivating the F.A.S.T.-key
Free-hand Advanced Secu- rity Transmitter (F.A.S.T.-key)
 (if so equipped)
The F.A.S.T.-key must be carried by the  driver. The F.A.S.T.-key is required for  vehicle operations su 
ch as locking and  
unlocking the doors and the liftgate,  starting the engine 
 and changing the  
operation mode. When 
 leaving the vehi- 
cle, make sure you are carrying the  F.A.S.T.-key and then lock the vehicle.
WA R N I N G Individuals who use 
implantable pace- 
makers or implanta 
ble cardiovascular- 
defibrillators should keep away from theexternal and internal 
 transmitters. The 
electromagnetic w 
aves used in the 
F.A.S.T.-key may affe 
ct the operation of 
implantable pacemakers and implantable cardiovascular-defibrillators.A- External transmitter B- Internal transmitter
WA R N I N G Individuals using ot
her electro-medical 
apparatus besides implantable pacemak-ers and implantable  
cardiovascular-defi- 
brillators should  
check with the 
manufacturer of the apparatus to confirm the effect of the el 
ectromagnetic waves 
used by the F.A.S.T.-key. The electromag- netic waves may affect 
 the operations of 
the electro-medical apparatus.NOTE
 The F.A.S.T.-key uses weak electromagnetic waves.In cases such as the following, operationmay be imprope 
r or unstable. 
• The vehicle is near a facility that emits strong electroma 
gnetic waves, such as a TV 
transmitting tower, a po 
wer station, a radio 
station or an airport
BK0278200US.book  15 ページ  2019年4月10日 水曜日 午前10時59分 
Page 97 of 443

Free-hand Advanced 
Security Transmitter (F.A.S
.T.-key) (if so equipped) 
5-16 Features and controls
5
N00503201249
When a person enters the operating range of the F.A.S.T.-key while carrying the F.A.S.T.-key and presses the driver’s or front passen- ger’s door lock/unlock switch, the liftgate LOCK switch or the liftgate OPEN switch,verification of the ID 
 code is performed. 
The doors and the liftgate can be locked and unlocked and the engine 
 can be started only 
when the ID codes of the vehicle and F.A.S.T.-key match. 
The operating range is  
within about 2.3 feet 
(70 cm) of the handles of the driver’s door,front passenger door and liftgate.
• The key is carried together with other com- munication devices such 
 as cellular phones 
or radios, or electrical appliances such ascomputers • The F.A.S.T.-key touches or is covered by a metal object • A keyless entry system is being used nearby • The battery of the F.A.S.T.-key is run down• The vehicle is in  
a location with strong 
electromagnetic  
waves or noise 
Use the emergency key to lock and unlock the driver’s door in such circumstances.Refer to “To operate 
 without using the 
F.A.S.T.-key” on page 5-29.  The F.A.S.T.-key is constantly performing reception opera 
tions in its communication 
with the vehicle. This means that the batteryis always running down, regardless of how often the F.A.S.T.-key is used. The battery life is approximately  
1 to 3 years, depending 
on the usage conditions.  Since the F.A.S.T.-key is constantly perform- ing reception operati 
ons, the reception of 
strong electrom 
agnetic waves 
can accelerate 
the running down of the ba 
ttery. Do not place 
near to electrical appliances such as televi- sions or computers.NOTE
Operating range of the  F. A . S . T. - k e y
 
NOTE
 When the battery of the F.A.S.T.-key has run down or there are st 
rong electromagnetic 
waves or noise in the area, the operating range could decrease  
or operations could 
become unstable.
Operating range for locking and  unlocking the doors and the lift-gate
 * : Front of the vehicle : Operating range
NOTE
 The door or liftgate switch can only be used for locking or unlocking when a matching F.A.S.T.-key is detected.  The system may not operate if the F.A.S.T.- key is too close to the windshield, door win-dows or liftgate.
BK0278200US.book  16 ページ  2019年4月10日 水曜日 午前10時59分 
Page 98 of 443

Free-hand Advanced Securi
ty Transmitter (F.A.S.T.-key) (if so equipped) 
Features and controls 5-17
5
N00503301077
The operating range is the interior of the vehicle.
N00503401472
While carrying the F.A.S.T.-key, press thedriver’s or front passenger’s door lock/unlockswitch (A), or the liftgate LOCK switch (B) within the operating range to lock all the doors and the liftgate. The turn signal lights will blink once and the buzzer will sound once. Also refer to “Doors locks”, “Power door locks”, “Liftgate” and “Power liftgate” on pages 5-36, 5-38, 5-40 and 5-42 respectively.
 Even if the F.A.S.T.-key is within about 2.3 feet (70 cm) of the handle of the driver’sdoor, front passenger’s door or liftgate, thesystem may not operate if the key is close to the ground or in a high position.  If the F.A.S.T.-key is within the operating range, even a person not carrying the F.A.S.T.-key can lock and unlock the doorsor the liftgate by pressing the driver’s or front passenger’s door lock/unlock switch, the liftgate LOCK switch or the liftgateOPEN switch.
Operating range for starting the  engine and changing the opera- tion mode
 
NOTE
* : Front of the vehicle : Operating range
NOTE
 Even if the F.A.S.T.-key is within the operat- ing range, it may not be possible to start the engine and change the  
operation mode if the 
key is in a storage space such as the glovecompartment, on top of the instrument panel, or in the door pocket or luggage compart- ment.  Even if the F.A.S.T.-key is inside the vehicle, it may not be possible to 
 start the engine and 
change the operation mode if the key is too close to a door or door window.
To operate using the F.A.S.T.- key
 
To  l o c k
 
Driver’s and front passenger’s door lock/unlock  switches
BK0278200US.book  17 ページ  2019年4月10日 水曜日 午前10時59分 
Page 99 of 443

Free-hand Advanced 
Security Transmitter (F.A.S
.T.-key) (if so equipped) 
5-18 Features and controls
5
While carrying the F.A.S.T.-key within the operating range, you can unlock the doorsand the liftgate by using the F.A.S.T.-key operation. The dome light will turn on for 30 seconds.The turn signal lights will blink twice and the buzzer will  
sound twice. 
Also refer to “Door locks”, “Power door locks”, “Liftgate” and “Power liftgate” onpages 5-36, 5-38, 5-40 and 5-42 respectively. Press the driver’s door lock/unlock switch (A) to unlock only the driver’s door. Within approximately 2 seconds, press thedriver’s door lock/unlock switch one more time to unlock all the  
doors and the liftgate. 
Press the front passenger’s door lock/unlock switch (B) or the liftgate OPEN switch (C) to unlock all the doors and the liftgate.
NOTE
 On the vehicles equipped with the mirror retractor switch, the out 
side rearview mirrors 
automatically retract when all doors and lift- gate are locked using the driver’s or front passenger’s door lock/unlock switch (A) orthe liftgate LOCK switch (B).  In cases such as the following, the F.A.S.T.- key does not operate. • There is a F.A.S.T.-key in the passenger compartment • A door or the liftgate is open or ajar• The operation mode 
 is not in OFF. 
 The liftgate OPEN switch (C) can be used to confirm that the vehicl 
e is locked properly. 
Press the liftgate OPEN switch withinapproximately 3 seconds of locking.  If the liftgate OPEN switch is pressed 3 sec- onds or more after the  
vehicle is locked, the 
doors and the liftga 
te are unlocked.
Liftgate switches
The time within which locking confirmation is possible can be adjusted. See an autho-rized Mitsubishi Motors 
 dealer for details. 
On a vehicle equipped  
with the Smartphone- 
link Display Audio (SDA 
), the function can 
be adjusted on the screen. For details, referto the separate owner’s manual.
To  u n l o c k
 
NOTE
NOTE
 On the vehicles equipped with the mirror retractor switch, the out 
side rearview mirrors 
automatically extend when the driver’s door is unlocked using the  
driver’s lock/unlock 
switch (A), front passenger’s doorlock/unlock switch (B)  
or the liftgate open 
switch (C).  Settings can be change
d so that all doors and 
the liftgate are unloc 
ked automatically by 
pressing the driver’s door lock/unlock switchonce. Refer to “Setting of door 
 and liftgate unlock 
function” on page 5-33.Driver’s door lock/unlock switch
BK0278200US.book  18 ページ  2019年4月10日 水曜日 午前10時59分 
Page 100 of 443

Free-hand Advanced Securi
ty Transmitter (F.A.S.T.-key) (if so equipped) 
Features and controls 5-19
5
N00513501216
To prevent vehicle theft, no F.A.S.T.-keys other than those regist 
ered in advance can be 
used to start the engi 
ne. (Electronic immobi- 
lizer function)While carrying the F.A.S.T.-key, the engine switch can be used  
to start the engine.
NOTE
If the doors and the liftgate are unlocked using the driver’s or front passenger’s doorlock/unlock switch when all doors and the liftgate are locked and no doors or the lift- gate are opened with 
in approximately 30 
seconds, the doors and th 
e liftgate will auto- 
matically re-lock.Front passenger’s door lock/unlock switchLiftgate OPEN switch
 The amount of time af
ter unlocking until the 
vehicle re-locks au 
tomatically can be 
adjusted. See an authorized MitsubishiMotors dealer for details. On a vehicle equipped  
with the Smartphone- 
link Display Audio (SDA), the functions canbe adjusted on the scre 
en. For details, refer 
to the separate owner’s manual.  The F.A.S.T.-key does not operate when the operation mode is not in OFF.  The doors and the liftgate cannot be unlocked by using the li 
ftgate OPEN switch 
for approximately 3 seconds after locking.  The time within which locking confirmation is possible can be adjusted. See an autho-rized Mitsubishi Motors 
 dealer for details. 
On a vehicle equipped  
with the Smartphone- 
link Display Audio (SDA 
), the function can 
be adjusted on the scre 
en. For details, refer 
to the separate owner’s manual.  Functions settings can 
be modified as stated 
below. See an authorized Mitsubishi Motors dealerfor details. On a vehicle equipped  
with the Smartphone- 
link Display Audio (SDA), the functions canbe modified on the scre 
en. For details, refer 
to the separate owner’s manual. • Activating the operati 
on confirmation func- 
tion (blinking of the turn signal lights) only during locking, or only during unlocking.NOTE
• Deactivating the operation confirmationfunction (blinking of th 
e turn signal lights) 
and buzzer. • Modifying the number of blinks in the operation confirmati 
on function (blinking 
of the turn signal lights). • Making the buzzer sound when the F.A.S.T.-key is removed from the passenger compartment when all the doors and the liftgate are closed.
Engine switch
 
NOTE
BK0278200US.book  19 ページ  2019年4月10日 水曜日 午前10時59分