ECO mode MITSUBISHI OUTLANDER III 2018 Owner's Manual

Free-hand Advanced
Security Transmitter (F.A.S
.T.-key) (if so equipped)
5
5. Press the engine switch.6. Confirm that all warning lights and warn-ing displays are functioning properly.
After several attempts
, you may experience
that the engine still does not start.1. Make sure that all electric devices, suchas lights, air conditi
oning blower and rear
window defogger, are turned off.2. While depressing the brake pedal, pressthe accelerator peda
l halfway and hold it
there, then crank th
e engine. Release the
accelerator pedal, immediately after theengine starts.
3. If the engine still wi
ll not start, the engine
could be flooded with too much gasoline.While depressing the brake pedal, pushthe accelerator pedal all the way downand hold it there, then press the engineswitch to crank the engine. If the enginedoes not start after 5 to 6 seconds, pushthe engine switch to stop cranking theengine, and release th
e accelerator pedal.
Put the operation mode in OFF. Wait afew seconds, and then press the engineswitch to crank the engine again whiledepressing the brake pedal, but do notpush the accelerator pedal. If the enginefails to start, repeat these procedures. Ifthe engine still will
not start, contact your
local Mitsubishi Motors dealer or a repairfacility of your choi
ce for assistance.
Startability of the en
gine with an ambient
temperature of -22 °F (-30 °C) or lowerWhen the ambient temperature is -22 °F (-30°C) or lower, it may not be possible to startfrom a standstill even wi
th the selector lever
in the

Free-hand Advanced Securi
ty Transmitter (F.A.S.T.-key) (if so equipped)
Features and controls 5-29
5
N00561100014
To add a F.A.S.T.-key, you must already have2 registered F.A.S.T.-keys. You need to regis-ter the ID code to the vehicle.Registering the ID code can be done by yourauthorized Mitsubishi Motors dealer. Or itcan be done by yourself (except for vehiclessold in Canada).For you to register the ID code yourself, fol-low the “Customer F.A.S.T.-key program-ming” procedure below.If you choose to have your authorizedMitsubishi Motors dealer register the IDcode, take your vehicle and all remainingF.A.S.T.-keys to your authorized MitsubishiMotors dealer.
N00561201227
You can program new F.A.S.T.-keys to thesystem if you have tw
o valid (already regis-
tered) F.A.S.T.-keys an
d a blank (not regis-
tered) F.A.S.T.-key.For F.A.S.T.-key programming, follow theprocedures below.1. Open the driver’s door.2. While carrying the first valid F.A.S.T.-key, put the operatio
n mode in ON. (Per-
form the following procedure within 30seconds.)
3. Insert the new F.A.S.T.-key into the keyslot in the illustrated direction.4. With the first valid F.A.S.T.-key, press theUNLOCK button for 4 to 10 seconds andpress the LOCK button during this time.5. Release in sequence the LOCK andUNLOCK buttons within 10 seconds ofpressing the LOCK butt
on in step 4. (Per-
form the following procedure within 30seconds.)6. With the second valid F.A.S.T.-key, pressthe UNLOCK button for 4 to 10 secondsand press the LOCK button during thistime.
Additional F.A.S.T.-keys

NOTE
You are provided with 2 F.A.S.T.-keys, butyou may register up to 4 F.A.S.T.-keys.You can obtain blank F.A.S.T.-keys speciallycut for your vehicle from your MitsubishiMotors dealer.
Customer F.A.S.T.-key program-ming (Except for vehicles sold in Canada)

NOTE
Keep the driver’s door open until F.A.S.T.-key programming is finished. Do not open orclose other doors.
BK0249100US.book 29 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Free-hand Advanced
Security Transmitter (F.A.S
.T.-key) (if so equipped)
5
7. Release in sequence the LOCK andUNLOCK buttons within 10 seconds ofpressing the LOCK button in step 6. Theimmobilizer display on the informationscreen in the multi-information displaywill blink.When registration of ID
code is complete,
the buzzer will sound 3 times and theimmobilizer display will come on for 30seconds.If an error occurs, F.A.S.T.-key program-ming will be terminated and the buzzerwill sound for 3 seconds.8. If you wish to register another F.A.S.T.-key, repeat the process from step 1 afterthe operation mode is put in OFF.9. When all F.A.S.T.-keys are registered,remove the F.A.S.T.-key from the keyslot.
N00515501281
Press the remote control transmitter buttonsto lock or unlock the doors and the liftgate.It can also help you
signal for attention by
setting off the panic alarm.
Press the LOCK button (1) to lock all thedoors and the liftgate.The turn signal lights will also blink once.
NOTE
F.A.S.T.-key programming will be termi-nated if the operation
mode is put in OFF
before the immobilizer
display starts blink-
ing.
NOTE
The immobilizer displa
y will go off immedi-
ately if the operation mode is put in OFF.Perform the operation when the interrupt dis-play screen is not show
ing. The interrupt dis-
play screen may prevent you from seeing theimmobilizer display.It is not possible to re
gister a F.A.S.T.-key if
the immobilizer displa
y goes off during the
procedure.
Keyless entry system

1-
LOCK ( ) button
2-
UNLOCK ( ) button
3- Power liftgate but
ton (if so equipped)
4- PANIC button5- Operation indicator light
NOTE
On vehicles equipped wi
th the mirror retrac-
tor switch, the outside rearview mirrors auto-matically retr
act or extend when the doors
and the liftgate are locked or unlocked usingthe remote control transmitter buttons.Refer to “Features a
nd controls: Outside
rearview mirrors” on page 5-60.
To l o c k

NOTE
On vehicles equipped wi
th the mirror retrac-
tor switch, the outside rearview mirrors auto-matically retract when the LOCK button (1)is pressed.If you press the LOCK button (1) twice, thehorn will sound once.
BK0249100US.book 30 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Free-hand Advanced Securi
ty Transmitter (F.A.S.T.-key) (if so equipped)
Features and controls 5-31
5
Press the UNLOCK button (2) to unlock thedriver’s door only.Within approximately 2 seconds, press theUNLOCK button one more time to unlock allthe doors and liftgate.The dome light will turn on for 30 seconds.The turn signal lights will also blink twice.The front side-marker
and parking lights will
also turn on for appr
oximately 30 seconds.
Refer to “Welcome light” on page 5-215.
The horn and turn signal lights of the keylessentry system answerback function can bechanged as required. This is done with thekey removed from the ignition switch.The answerback function can be set in thefollowing three ways.1. Put the operation mode in OFF.2. Open the driver’s door and turn the com-bination headlights a
nd dimmer switch to
the “OFF” position.3. Press the LOCK button (1) for 4 to 10 sec-onds and press the UNLOCK button (2)during this time.4. Release in sequence the UNLOCK andLOCK buttons within 10 seconds ofpressing the UNLOCK button in step 3.
The answerback function from the turn signallights can be turned ON or OFF separately.1. Put the operation mode in OFF.2. Open the driver’s door and turn the com-bination headlights and dimmer switch tothe “OFF” position.3. Press the UNLOCK button (2) for 4 to 10seconds and press the LOCK button (1)during this time.4. Release in sequence the UNLOCK andLOCK buttons within 10 seconds ofpressing the LOCK button in step 3.
To u n l o c k

NOTE
On vehicles equipped wi
th the mirror retrac-
tor switch, the outside rearview mirrors auto-matically extend when
the UNLOCK button
(2) is pressed.On a vehicle equipped with the SmartphoneLink Display Audio, the functions can beadjusted on the screen. For details, refer tothe separate owner’s manual.The door and liftgate unlock function can beset so that all doors and liftgate unlock whenthe UNLOCK button (2) is pressed once.Refer to “Setting of door
and liftgate unlock
function” on page 5-32.
Answerback function

Horn deactivation/reactivationOne chime: The horn will not sound.Two chimes: The horn will sound.Four chimes: The horn will sound if the
LOCK button is pressed twicewithin 1 second.
NOTE
On a vehicle equipped with the SmartphoneLink Display Audio, the functions can beadjusted on the screen. For details, refer tothe separate owner’s manual.
Turn signal light deactivation/reactiva-tionNumber of chimes
To l o c k
To u n l o c k
One chime One flash Two flashesTwo chimes One flash No flashThree chimes No flash Two flashesFour chimes Two flashes One flashFive chimes No flash One flash
BK0249100US.book 31 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Free-hand Advanced
Security Transmitter (F.A.S
.T.-key) (if so equipped)
5
The buzzer answerback function can beturned ON or OFF as required.
N00544601141
The door and liftgate
unlock function can be
set to the following two conditions.Each time the door and
liftgate unlock func-
tion is set, a chime wi
ll sound to tell you the
condition of the door and liftgate unlockfunction.1. Put the operation mode in OFF.2. Open the driver’s door and turn the com-bination headlights and dimmer switch tothe “OFF” position.3. Press the LOCK button (1) for 4 to 10 sec-onds and press the UNLOCK button (2)during this time.4. Release in sequence the LOCK andUNLOCK buttons within 10 seconds ofpressing the LOCK button in step 3.
N00579500020
After unlocking the doors and the liftgate, thepower liftgate can be operated by pressing thepower liftgate button (3).Refer to “Power lift
gate” on page 5-39.
N00544701113
If you are near your vehicle and feel threat-ened, you can activate the alarm to call atten-tion as follows:1. Press the PANIC button (4) for more than1 second.2. The headlights will blink on and off andthe horn will sound intermittently forapproximately 3 minutes.3. To turn off the alarm, press any button onthe remote control transmitter.
Six chimes Two flashes No flashSeven chimes No flash No flash
NOTE
On a vehicle equippe
d with the Smartphone
Link Display Audio, the functions can beadjusted on the screen. For details, refer tothe separate owner’s manual.
Buzzer deactivation/reactivation
NOTE
On a vehicle equippe
d with the Smartphone
Link Display Audio, the functions can beadjusted on the screen. For details, refer to aseparate owner’s manual.
Setting of door and liftgate unlock function

Number of chimes
To l o c k
To unlock
Number of chimes
Condition
One chime
All doors and the liftgate unlock
Tw o chimes
Driver’s door unlock only
NOTE
On a vehicle equipped with the SmartphoneLink Display Audio, the functions can beadjusted on the screen. For details, refer tothe separate owner’s manual.
Operating the power liftgate

Using the panic alarm

NOTE
The indicator light (5) comes on each time abutton is pressed.The F.A.S.T.-key can be used from approxi-mately 40 feet (12 m) away. However, thisdistance may change if
your vehicle is near a
TV transmitting tower,
a power station, or a
radio station.
BK0249100US.book 32 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Power liftgate (if so equipped)5-42 Features and controls
5
The operation mode is in ON with theselector lever in the “P” (PARK) position,or the operation mode is in ACC or OFF.The power liftgate is completely open.Nothing is touching the auto reverse sen-sors on the power liftgate.
After unlocking the doors and the power lift-gate, the power liftgate can be operated bypressing the switch (A) of the F.A.S.T.-key orthe driver’s side power liftgate switch (B).
If the power liftgate switch is pressed twice ina row, the power liftgate operates after thewarning buzzer sounds and the hazard warn-ing flasher blinks.The power liftgate operates as follows:
If the power liftgate switch is pressed oncewhile the power liftgate is operating, thewarning buzzer sounds an
d the liftgate will
reverse and return to
the full open or closed
position.If the driver’s side power liftgate switch ispressed for more than 1 second, the powerliftgate will operate
after the buzzer sounds
and the hazard warning flasher blinks.The power liftgate operates as follows.
Operating the power liftgate using the F.A.S.T.-key or the driver’s side power liftgate switch

•While closed: The
warning buzzer sounds
and the power liftgate com-pletely opens.
•While open: The warning buzzer sounds
and the power liftgate com-pletely closes.
NOTE
If the power liftgate sw
itch is pressed 3 or
more times in a row, the power liftgate maynot operate normally.If this occurs, wait a short time before againpressing the power lift
gate switch twice.
•While closed: The warning buzzer sounds
and the power liftgate com-pletely opens.
•While open: The warning buzzer sounds
and the power liftgate com-pletely closes.
BK0249100US.book 42 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Theft-alarm system
Features and controls 5-47
5
N00510301226
Park the vehicle and st
op the engine. Arm the
system as described below.1. Except for vehicles equipped with theF.A.S.T.-key, remove the key from theignition switch.For vehicles equipped with the F.A.S.T.-key, put the operation mode in OFF.2. Make sure that the engine hood is closed.3. Lock all doors and the liftgate by usingthe keyless entry system or the F.A.S.T.-key operation.
At this time, the theft-alarm indicator (A)mation.4. The system has entered the armed stageafter about 20 seconds, when the theft-alarm indicator (A) flashing becomesslower.The theft-alarm indicator (A) continues toflash while the system is in the armedstage.
N00510401230
The alarm will be activated if any of the fol-lowing occur while the ve
hicle is parked and
the system is armed.One of the doors and the liftgate is openedwithout using the keyless entry system orthe F.A.S.T.-key operation.The engine hood is opened.
CAUTIONDo not modify or add parts to the theft-alarmsystem. Doing so could cause the theft-alarmto malfunction.
Armed stage Arm the system and leave
NOTE
If the engine hood is open, the theft-alarmindicator (A) illuminates and the system can-not enter the armed stage.The system enters the armed stage about 20seconds after the e
ngine hood is closed.
The system will be disarmed if, while thetheft-alarm indicator (A) is illuminated, alldoors and the liftgate are unlocked by usingthe keyless entry system or the F.A.S.T.-keyoperation.
The system will be disarmed if, while thetheft-alarm indicator is illuminated, the fol-lowing operation is performed.• Except for vehicles equipped with theF.A.S.T.-key, if the ignition switch is turnedto the “ON” position.• For vehicles equippe
d with the F.A.S.T.-
key, if the operation mode is put in ON.
The system will not be armed if a door, theliftgate or the engine
hood is not completely
closed. If this happens, rearm the system asdescribed above.The theft-alarm system can be activatedwhen people are riding inside the vehicle orwhen the windows are open. To prevent acci-dental activati
on of the alarm, do not set the
system to the system armed mode while peo-ple are riding in the vehicle.
Alarm stage
NOTE
BK0249100US.book 47 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Theft-alarm system5-48 Features and controls
5
N00582500040
When the alarm is activated:1. The headlights blink on and off for 3 min-utes.After 3 minutes the headlights automati-cally shut off.2. The horn will sound intermittently for 3minutes.
N00582600025
The alarm can be deacti
vated in the following
ways.By using the keyless entry system or theF.A.S.T.-key operation to lock or unlockthe doors and liftgate.Turn the ignition switch to the “ON” posi-tion or put the operation mode in ON.
N00510501202
The system will be disarmed if the followingoperation is performed.Except for vehicles equipped with theF.A.S.T.-key, if the ignition switch isturned to the “ON” position.For vehicles equipped with the F.A.S.T.-key, if the operation mode is put in ON.All doors and the lift
gate are unlocked by
using the keyless entry system or theF.A.S.T.-key operation.
Type of alarm
NOTE
The alarm will continue
to operate for 3 min-
utes. At the end of that
period, the alarm will
automatically shut off
to save battery power.
The system will then be rearmed until theproper disarming step is taken.The alarm will resu
me if unauthorized
actions are taken again, even if the alarm hasstopped.Horn sounds!Headlights blink on and off!
Alarm deactivation Disarmed stage
NOTE
If the UNLOCK button on the remote controltransmitter, or the driver’s or front passen-ger’s door lock/unlock switch is pressedwhen all doors and the li
ftgate are closed and
no door is opened with
in approximately 30
seconds, re-arming will
automatically occur.
The amount of time after unlocking until thevehicle relocks automatically can beadjusted. See an authorized MitsubishiMotors dealer for details.On a vehicle equipped with the SmartphoneLink Display Audio, the functions can beadjusted on the screen. For details, refer to aseparate owner’s manual.Once the system has been disarmed, it can-not be rearmed except
by repeating the arm-
ing procedure.Disarm...by using the keyless entry system or F.A.S.T.-key operation
BK0249100US.book 48 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Power window control5-50 Features and controls
5
N00548701137
The main switch located on the driver’s doorcan be used to operate all the windows.A window can be opened or closed by operat-ing the corresponding switch.Press the switch down to open the window,and pull up the switch to close it.If the driver’s door window switch is fullypressed down/pulled up, the driver’s doorwindow automatically opens/closes com-pletely.If you want to stop the window movement,operate the switch lightly in the reverse direc-tion.
N00548800102
Each sub-switch can be used for it’s own pas-senger door window, unless the driver’s win-dow lock switch is activated.
N00548901155
The power windows can be run up or downwhen the ignition switch or the operationmode is in ON.The door windows can be opened or closedfor a 30-second period after the engine is
stopped. However, once the driver’s door orthe front passenger’s door is opened, thepower windows cannot be operated.
N00549001166
When this switch is in the lock mode, the pas-senger door switches cannot be used to openor close the door windows, and the mainswitch will open or
close only the driver’s
door window. To unlock the switch, press itagain.
Main switch 1- Driver’s door window switch2- Front passenger door window switch3- Left rear door window switch4- Right rear door window switch5- Lock switch
Sub switch 1- Close2- Open
NOTE
The rear door windows open only half-way.
Power window timer function
Lock switch 1- Lock2- Unlock
BK0249100US.book 50 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Sunroof (if so equipped)
Features and controls 5-51
5
N00528801129
If a hand or head is trapped, for safety thedoor window is automati
cally lowered a little.
After the obstruction is removed, pull up theswitch again to close the door window.
N00551400014
Wind buffeting can be described as the per-ception of pressure on the ears or a boomingor rumbling sound. Your vehicle may exhibitwind buffeting when driving with one or bothrear door windows down or partially opened.This is a normal occurrence that can be mini-mized. If the buffeting
occurs with the rear
door windows open, open the front door win-dows as well as the rear door windows tominimize the condition.
N00511001682
The sunroof can be ope
ned and closed with
the ignition switch or the operation mode inON.
WA R N I N GBefore driving with a child in the vehicle,be sure to lock the window switch to makeit inoperative. Children tampering withthe switch could easily trap their hands orheads in the window.
Safety mechanism (Driver’s door window only)
WA R N I N GIf the battery terminals are disconnectedor the fuse for electric window is replaced,the safety mechanism will be cancelled.If a hand or head got
trapped, a serious
injury could result.CAUTIONThe safety mechanism is deactivated justbefore the door window closes. This allowsthe door window to close completely. There-fore be especially care
ful that fingers are not
trapped in the door window opening.
The safety mechanism is deactivated whilethe switch is pulled up.
Therefore be espe-
cially careful that fi
ngers are not trapped in
the door window opening.Do not deliberately trap your hands or headin order to activate the safety mechanism.Your hand or head coul
d be trapped and per-
sonal injury could result.NOTE
The safety mechanism can be activated if thedriving conditions or
other circumstances
cause the door window to be subjected to aphysical shock similar to that caused bytrapped hand or head.If the battery terminals are disconnected orthe fuse for power window is replaced, thesafety mechanism will
be cancelled and the
door window will not automaticallyopen/close completely.If the window is open,
repeatedly raise the
driver’s door window switch until the win-dow has been fully closed.Following this, release the switch, raise theswitch once again and hold it in this condi-tion for at least 1 second, then release it. Youshould now be able to operate the driver’sdoor window in the normal function.CAUTION
What to do if you hear wind buffeting when driving Sunroof
(if so equipped)
BK0249100US.book 51 ページ ２０１７年５月１０日　水曜日　午前８時４９分