display MITSUBISHI OUTLANDER PHEV 2014 (in English) Service Manual

4.Lightly press the multi information dis-
play switch to select the units.
5. Press and hold the multi information dis-
play switch for about 2 seconds or more to change the setting to the selected unit.NOTEl The display units for the average fuel con-
sumption and the driving range is switched, but the units for the indicating needle
(speedometer), the odometer and the tripme-
ter will remain unchanged.
The distance units is also switched in the fol-
lowing combinations to match the selected
fuel consumption unit.
Fuel consumptionDistance (driving
range)L/100 kmkmmpg (US)mile(s)mpg (UK)mile(s)km/LkmChanging the temperature unit
E00523101737
The display unit for temperature can beswitched.
1. Press and hold the multi information dis-
play switch for about 2 seconds or more to switch from the setting mode screen
to the menu screen.
Refer to “Changing the function set-
tings” on page 6-16.
2. Lightly press the multi information dis-
play switch to select “
” (temperature
unit setting).
3. Press and hold the multi information dis-
play switch for about 2 seconds or more
to switch in from °C to °F, or from °F to °C. The setting is changed to the selec-
ted temperature unit.
NOTEl The temperature value on air conditioner
panel is switched in conjunction with outside
temperature display unit of the multi infor-
mation display.
However, “°C” or “°F” are not shown to
temperature display of an air conditioner.
l On vehicles equipped with
MITSUBISHI
Multi-Communication System (MMCS), the
temperature value of the air conditioner
screen of MITSUBISHI Multi-Communica-
tion System (MMCS) is switched in con- junction with outside temperature display
unit of the multi information display.
However, “°C” or “°F” are not shown to the air conditioner screen.Changing the display language
E00523201741
The language of the multi information dis-
play can be switched. 1. Press and hold the multi information dis-
play switch for about 2 seconds or more to switch from the setting mode screen
to the menu screen.
Refer to “Changing the function set-
tings” on page 6-16.
2. Lightly press the multi information dis-
play switch to select “LANGUAGE”
(language setting).
3. Press and hold the multi information dis-
play switch for about 2 seconds or more to display “LANGUAGE”.
4. Lightly press the multi information dis-
play switch to select the desired lan-guage.
Multi information display
6-19OGGE14E5Instruments and controls6

5.If you hold down the multi information
display switch for about 2 seconds or
more, the setting is changed to the selec- ted language.NOTEl If “---” is selected in the language setting, a
warning message is not displayed whenthere is a warning display or interrupt dis-
play.Changing the language cooper-
ative control
E00523301582
The language used in MITSUBISHI Multi-
Communication System (MMCS) (if so
equipped) or the Bluetooth ®
2.0 interface (if
so equipped) can be changed automatically to the same language as that shown in the multi
information display. 1. Press and hold the multi information dis-
play switch for about 2 seconds or more to switch from the setting mode screen
to the menu screen.
Refer to “Changing the function set- tings” on page 6-16.
2. Lightly press the multi information dis-
play switch to select “
” (language co-
operative control).
3. Press and hold the multi information dis-
play switch to switch from A/1 (lan- guage cooperation enabled) to M/2/P
(language cooperation disabled), or from
M/2/P to A/1.
The setting is changed to the selected condition.
NOTEl The language display modified with the lan-
guage setting can be switched in the follow-ing manner.NOTE• When A (language cooperation enabled)
or 1 has been selected with the language cooperative control, the language for
MITSUBISHI Multi-Communication Sys-
tem (MMCS) (if so equipped) or the
Bluetooth ®
2.0 interface (if so equipped)
is automatically changed to the language selected for the multi information display.
However, this changing function may not
work depending on the language selected for the multi information display.
• When M (language cooperation disabled),
2 or P has been selected with the language cooperative control, the language for MITSUBISHI Multi-Communication Sys-tem (MMCS) (if so equipped) or the
Bluetooth ®
2.0 interface (if so equipped)
is not automatically changed to the lan- guage selected for the multi information
display.
l The language on the display of the audio
system (if so equipped) is not automatically
changed even if you select A or 1 of the lan-
guage cooperation control.
Multi information display
6-20OGGE14E5Instruments and controls6

Operating sound under charg-ing or remote climate control
E000204600023
Even if the operation mode of the power
switch is OFF, you may hear the operating
sound such as cooling fan for cooling the
drive battery during charging, the air condi- tioning compressor and for remote climate control (if so equipped).
But this is not a malfunction.
Refer to “Remote Climate Control” on page
3-23.
Changing the time until “REST
REMINDER” is displayed
E00523501702
The time until the display appears can be changed. 1. Press and hold the multi information dis-
play switch for about 2 seconds or moreto switch from the setting mode screen
to the menu screen.
Refer to “Changing the function set-
tings” on page 6-16.
2. Lightly press the multi information dis-
play switch to select “ALARM” (rest
time setting).
3. Press and hold the multi information dis-
play switch for about 2 seconds or moreto display “ALARM”.
4. Lightly press the multi information dis-
play switch to select the time until the display.
5. Press and hold the multi information dis-
play switch for about 2 seconds or more,the setting is changed to the selected
time.NOTEl The drive time is reset when the operation
mode of the power switch is put in OFF.Changing the turn-signal sound
E00529100396
It is possible to change the turn-signal sound.
1. Press and hold the multi information dis-
play switch for about 2 seconds or more to switch from the setting mode screen
to the menu screen.
Refer to “Changing the function set- tings” on page 6-16.
2. Lightly press the multi information dis-
play switch to select
(changing the
turn-signal sound).
3. Press and hold the multi information dis-
play switch for about 2 seconds or moreto switch from 1 (turn-signal sound 1) to
2 (turn-signal sound 2), or from 2 to 1.
The setting changes to the selected turn-
signal sound.
Returning to the factory set-
tings
E00523601921
Many of the function settings can be returned
to their factory settings. 1. Press and hold the multi information dis-
play switch for about 2 seconds or more to switch from the setting mode screen
to the menu screen.
Refer to “Changing the function set- tings” on page 6-16.
2. Lightly press the multi information dis-
play switch to select “RESET” (return- ing to the factory settings).
3. When you press and hold the multi in-
formation display switch for about 5 sec-
onds or more, the buzzer sounds and all of the function settings are returned to
the factory settings.
NOTEl The factory settings are as follows.
• Average fuel consumption reset mode: A
(Auto reset)
• Fuel consumption display unit: L/100 km
• Temperature unit: °C (Celsius)
• Display language: ENGLISH or RUSSI-
AN
• Cooperative language setting: A (lan-
guage cooperation enabled)
Multi information display
6-21OGGE14E5Instruments and controls6

NOTE•Operation sounds: ON (Operation sounds
on)
• “REST REMINDER” display: OFF
• Turn-signal sound: Turn-signal sound 1
l The low tyre pressure warning threshold and
tyre ID set cannot be returned to their facto-
ry settings.
Multi information display
6-22OGGE14E5Instruments and controls6

Indication lamp, warning lamp, and information screen display listE00523701182
Indication and warning lamp list
E00523802122
1- Position lamp indication lamp ® p. 6-42
2- Front fog lamp indication lamp ® p. 6-42
3- Turn-signal indication lamps/Hazard warning indication lamps ® p. 6-41
4- Rear fog lamp indication lamp ® p. 6-42
5- High-beam indication lamp ® p. 6-416- Plug-in Hybrid EV System warning
lamp ® p. 6-44
7- Auxiliary battery charge warning lamp ® p. 6-43
8- Charging indicator ® p. 6-42
9- Regenerative brake warning lamp ® p. 6-44
10- Ready indicator ® p. 6-4211- Acoustic Vehicle Alerting System
(AVAS) OFF indication lamp
® p. 7-24
12- Active Stability Control (ASC) indica- tion lamp ® p. 7-33
13- Active Stability Control (ASC) OFF in- dication lamp ® p. 7-33
14- Anti-lock brake system (ABS) warning lamp ® p. 7-29
Indication lamp, warning lamp, and information screen display list
6-23OGGE14E5Instruments and controls6

15- Supplement Restraint System (SRS)warning lamp ® p. 5-35
16- Check engine warning lamp ® p. 6-4317- Seat belt warning lamp ® p. 5-11
18- Tyre pressure monitoring system warn- ing lamp ® p. 7-6419- Brake warning lamp ® p. 6-42
20- Information screen display list ® p. 6-24

Information screen display list
E00523901344
When there is information to be announced, such as lamp reminder, the buzzer sounds and the screen switches to the displays shown below.
Refer to the appropriate page and take the necessary measures.
When the cause of the warning display is eliminated, the warning display goes out automatically. Refer to “Warning display list” on page 6-24.
Refer to “Navigation information display” on page 6-35. Refer to “Other interrupt displays” on page 6-37.
NOTEl A warning may be displayed on the information screen and the buzzer may sound in the following rare cases.
This is caused by the system picking up interference such as noise or strong electromagnetic waves, and is not a functional problem.
• An extremely strong electromagnetic wave is received from a source such as an illegal radio set, a spark from a wire, or a radar station.
• Abnormal voltage or a static electricity discharge is generated by the operation of installed electrical equipment (including after-market parts).
If the warning display appears many times, we recommend you to consult a MITSUBISHI MOTORS Authorized Service Point.

Warning display list
E00524002046
ScreenCauseSolution (Reference)l One or more minor failure is occurring in
the Plug-in Hybrid EV System.l Have your vehicle inspected by a
MITSUBISHI MOTORS Authorized
Service Point.
Indication lamp, warning lamp, and information screen display list
6-24OGGE14E5Instruments and controls6

ScreenCauseSolution (Reference)lOne or more failure is occurring in the
Plug-in Hybrid EV System.l Immediately park the vehicle in a safe
place and contact a MITSUBISHI
MOTORS Authorized Service Point.l The parking lock unit is in failure. The
Plug-in Hybrid EV System cannot be keptin standstill condition without applying the parking brake.l Park the vehicle at a safe, flat place and
apply the parking brake. Contact a
MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Electrical Parking switch” on page 7-14.l You are attempting to set the operation
mode to “ON” when the charge connector
is connected to the charge port.l Disconnect the charge connector from the
charge port before operating the power switch.l Charging was interrupted due to system
failure (electric leak detected).l There is an electric leak or the normal
charge cable is faulty. Immediately stop using the cable and contact a
MITSUBISHI MOTORS Authorized
Service Point.l Charging was interrupted due to poor con-
nection of the charge cable or power fail- ure.l Connect the charge cable correctly.
Refer to “Normal charging” on page 3-10.
Refer to “Quick charging” on page 3-16.
l If charging is interrupted due to a power
failure, charging will be automatically re-sumed when the power is restored.
Indication lamp, warning lamp, and information screen display list
6-25OGGE14E5Instruments and controls6

ScreenCauseSolution (Reference)lThe drive battery temperature is too cold.l When the vehicle is under running, stop
the vehicle in a safe place and contact a MITSUBISHI MOTORS Authorized
Service Point.
l When the vehicle is parked during the
daytime, wait for the outside temperature to rise and re-start the Plug-in hybrid sys-tem once the outside temperature has ris-
en.
Refer to “Cautions and actions to deal with intense cold” on page 2-09.l You have forgotten to turn off the lamps.l Refer to “Lamps (headlamps, fog lamp,
etc.) auto-cutout function” on page 6-45.l There is a fault in the keyless operation
system.l Refer to “Keyless operation system” on
page 4-06.
Indication lamp, warning lamp, and information screen display list
6-26OGGE14E5Instruments and controls6

ScreenCauseSolution (Reference) lThere is a fault in the keyless operation
system.l Refer to “Keyless operation system” on
page 4-06. l The keyless operation key is not detected.lInsert the keyless operation key into the
key slot.
Refer to “If the keyless operation key is not operating properly” on page 7-12.
Indication lamp, warning lamp, and information screen display list
6-27OGGE14E5Instruments and controls6

ScreenCauseSolution (Reference)lYou have forgotten to remove the keyless
operation key from the key slot.l Remove the keyless operation key from
the key slot.
Refer to “Keyless operation key remind-
er” on page 7-12.l There is a fault in the EPS.l Have the vehicle inspected by a
MITSUBISHI MOTORS Authorized
Service Point as soon as possible.
Refer to “Electric power steering system
(EPS)” on page 7-30.l The brake fluid level in the reservoir has
fallen to a low level.
l There is a fault in the brake system.lImmediately stop the vehicle in a safe
place.
We recommend you to consult a MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Brake warning display” on page 6-44.l When the brake pedal has been repeatedly
depressed over a short period of time, the
brake warning lamp may come on and the brake warning buzzer may sound, and this warning may be displayed.l If this warning display disappears and the
brake warning lamp goes out and the buz-
zer stops a few seconds after stopping brake operation, there is no abnormality.l The RBS (regenerative brake system) can-
not be used.l We recommend you to consult a
MITSUBISHI MOTORS Authorized
Service Point.
Indication lamp, warning lamp, and information screen display list
6-28OGGE14E5Instruments and controls6