clock MITSUBISHI PAJERO IV 2011 Owner's Manual

2. Remove the bulb from the socket by pulling
out. 3. To install the bulb, perform the removal
steps in reverse.
Front turn-signal lamps E01003800733
1. Turn
the
bulb socket anticlockwise to re-
move it.
2. Remove

the bulb from the socket by pulling
out. 3. To install the bulb, perform the removal
steps in reverse.
Front fog lamps* E01004001553
1. Remove the

5 clips (A, C) and screw (B) by
following procedures

then turn up the cover
(D). 2. Depress the tab (E) on the harness connector
(F) and

pull the harness connector to remove
it. 3. Remove the entire socket and bulb assembly
(G) by turning it anticlockwise. CAUTION
l
Handle halogen
lamp
bulbs with care.
The gas inside halogen lamp bulbs is high-
ly pressurized, so dropping, knocking, or
scratching a halogen lamp bulb can cause
it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the
bulb to break the next time the fog lamps
are operated. If the glass surface is dirty,
it must be cleaned with alcohol, paint thin-
ner, etc., and refit it after drying thorough-
ly. Maintenance
8-26
8

OBKE12E1

4. To install the bulb, perform the removal
steps in reverse.
NOTE l When
refitting
the clips (H and I) of the cov-
er, push the pin (J). Rear combination lamps
E01004200659
On corner side 1.Remove the screws that hold the lamp unit.
2. Slide

the lamp unit out sideways to remove it.
Left side
Right side 3. Remove the socket and bulb assemblies by
turning them
anticlockwise. Remove the
bulb by pulling it out.
3-door models 5-door models A- Rear turn-signal lamp*
B- Stop and tail lamp* Stop lamp*
C- Reversing lamp
4.

To install the bulb, perform the removalsteps in reverse.
On bumper* 1. Remove the lens mounting screws. Maintenance
8-27 8

OBKE12E1

2. Remove the socket and bulb assembly togeth-
er by turning it anticlockwise, and then re-
move the bulb by pulling it out. D- Rear turn-signal lamp
E- Tail lamp
3. To install the

bulb, perform the removal
steps in reverse.
Rear fog lamp E01004100371
1. Open the spare wheel garnish (A). (Refer to
“To remove the spare wheel” on page 6-10). 2. Remove the socket and bulb assembly (B) by
turning it
anticlockwise, and then remove the
bulb by pulling it out. 3. To install the bulb, perform the removal
steps in reverse.
High-mounted stop lamp (bulb type)* E01004500535
1. Insert
a

straight blade (or minus) screwdriver
with a

cloth over at the edge of the cover and
pry gently to remove the cover. 2. Remove the socket and bulb assembly togeth-
er by
turning it anticlockwise, and then re-
move the bulb by pulling it out. 3. To install the bulb, perform the removal
steps in reverse.
Licence plate lamps E01004600709
1. Remove
the

lens mounting screws and re-
move the socket and bulb assembly. Maintenance
8-28
8

OBKE12E1

2. Remove the socket and bulb assembly (A) to-
gether by turning it anticlockwise and then re-
move the bulb by pulling it out. 3. To install the bulb, perform the removal
steps in reverse. NOTE
l When
installing the
lens, make sure the direc-
tion of the lens is installed as shown in the il-
lustration. *: Right side of the vehicle
Room & map lamps E01004700524
1. Insert a straight blade (or minus) screwdriver
with a

cloth over its tip into the lens and pry
gently to remove it. 2. Remove the bulb from the lamp holder.3. To install the bulb, perform the removal
steps in reverse.
NOTE l When installing

the lens, align the tab on the
lens with the hole on the vehicle side. Rear personal lamps
E01005200252
When replacing a bulb, keep the interior lamp
switch in the “ ” (OFF) position. Maintenance
8-29 8

OBKE12E1