buttons MITSUBISHI SHOGUN 2003 Owner's Manual (in English)

G15B094D
Manual modeThe manual adjustment mode is also available in case the“Auto
mode ”show sth e incorrec ttim ewhe nthe incorrect
RDS signal
is
recieved .
For manual time adjustment, use the below procedure:
1. Switch off the audio once by pressing the PWR switch (1).
2. While pressing the CH4 button (2), press the PWR switch (1) until it beeps. The “CT” display (A) disappears and this is the“Manual adjustment mode”.
3. Set the time by pressing the various buttons as described below. H -To adjust the hour
M -To adjust the minutes
SET -To reset the minutes to zero
10:30-11:29...Changes to 11:00
11:30-12:29...Changes to 12:00
Instruments and controls
4-30Div:
Out put date:

D92N009A
Date
(Diesel-powered vehicles only)
ED92N-C
Set the date by pressing the various but-
tons as described below:
1. Press the“M”button while pressing the
button (A) to activate the date setting
function.
2. Press button (A) to select the“day”.
Then, press the“M”or“H”button to
adjust the desired“day”.
To change the date quickly, press the
“M”or“H”button for about 2 seconds or
longer.3. Press the button (A) to select the
“month”. Then, press the“M”or“H”but-
ton to adjust the desired“month”.
To change the month quickly, press the
“M”or“H”button for about 2 seconds or
longer.
4. Press the button (A) to select the“year”.
And then, press the“M”or“H”button to
adjust the desired“year”.
To change the year quickly press the
“M”or“H”button for about 2 seconds or
longer.
5. Press the“SET”button to determine the
setting.
NOTE
(1) If the battery cables are discon-
nected, reset the correct date to cor-
rect the date after reconnecting.
(2) If no buttons are pressed for more than
approx. 15 seconds, the display will
return to the original display.
D92J011A
Display brightness adjustment /
Display unit selection
ED92L-C
Display brightness adjustment
1. Press the“H”button while pressing the
button (A) to activate the display bright-
ness selection function.Instruments and controls
4-35
Div:
Out put date:

D92J006A
2. Adjust the brightness by moving the cur-
sor with the“H”or“M”button.
H-Decrease brightness
M-Increase brightness
D92J012A
3. Press the“SET”button to determine the
setting. The display will return to the
original display item.
NOTE
(1) To cancel the brightness adjusting pro-
cedure before completion, press the
button (A).
(2) If no buttons are pressed for more than
approx. 15 seconds, the currently
selected brightness is set automati-
cally. Then, the display returns to the
original display item.
D92J013A
Display unit selection
(Petrol-powered vehicles only)
ED92J-B
Originally, km/h and L/100km are selected.
When you want to select the unit“mile”, fol-
low this procedure.
NOTE
For vehicles without MITSUBISHI genu-
ine audio, only the unit of average fuel con-
sumption can be changed to km or miles
as you like.
1. Press the“M”button while pressing the
button (A) to activate the display unit
selection function. The currently selected
unit will appear.
Instruments and controls
4-36Div:
Out put date:

(5) If no buttons are pressed for more than
approx. 15 seconds, the currently
selected unit is set automatically. Then,
the display returns to the original dis-
play item.
D92M001A
When battery terminals are
disconnected
ED92M-C
The car type setting is erased when the
battery terminals are disconnected.
Re-enter the setting as follows:
1. Turn the ignition switch to the“ON”or
“ACC”position to activate the car set-
ting mode. The words“CAR TYPE”will
flash on the display.
D92M007A
2. In a 3-door models, press the“H”but-
ton once. (The word“SHORT”will be
displayed as shown in the illustration.)
In 5-door models, press“M”button
once. (The word“LONG”will be dis-
played as shown in the illustration.)
Instruments and controls
4-38Div:
Out put date:

D92A051D
RV meter*
ED92A-P
1. Display for function buttons
This shows the options for each function button.
2. Digital clock→page 4-53
3. Compass
This display shows the direction of the vehicle.
4. Function buttons
Press this button to select options shown in the display.
5.“ADJ”button→page 4-43, 4-56, 6-10, 6-25
Press this button to adjust the brightness, date and time on the
display and select the RDS language.
6.“DISP”button→page 4-41
Press this button to change the display.
Instruments and controls
4-40Div:
Out put date:

NOTE
(1) Placing a cellular phone in the moni-
tor’s small storage compartment may
weaken the phone’s reception. This
does not indicate a fault with the sys-
tem.
(2) Use of wireless devices such as trans-
ceivers or a cellular phone near the
monitor may make the following con-
dition on the display. This does not indi-
cate a fault with the system.

The screen goes dark temporarily.

The compass may not show the cor-
rect direction.
(3) The following characteristics of the liq-
uid crystal display may be evident
under some circumstances and this
does not indicate a fault with the sys-
tem.

The appearance of small black
patches and spots of red, blue and
green lights.

The display goes dark, turns red or
moves slowly during cold weather.

The colour and brightness of the dis-
play change according to angle of
view.
Care of the monitorIf the monitor (the liquid crystal display)
becomes covered in fingerprints or other-
wise dirty, clean it with a soft and dry cloth.
NOTE
Don’t use a wet cloth or abrasive cleaner
as this may cause damage.
D92A053A
How to switch off or adjust the
brightness of the display
ED92L-B
Press the“ADJ”button to display the
options for the function buttons.
After 10 seconds, the display will be auto-
matically resumed.
Instruments and controls
4-42Div:
Out put date:

D92A054A
How to adjust the display brightness
1. Press the“BRIGHT”function button.
D92A055A
2. Adjust brightness as desired pressing
the“”or“”function buttons.
“”makes the display brighter.
“”makes the display darker.
3. The monitor will revert to the original dis-
play about 10 seconds after adjust-
ment with the function buttons is
finished.
NOTE
(1) Separate settings can be made for
when the lights are turned on and off.
(2) Whenever the monitor is not oper-
ated on, the previous display will be
resumed after about 10 seconds.
D92A056A
Switching off the display
1. Press the“BRIGHT”function button.Instruments and controls
4-43
Div:
Out put date:

D11C087B
Setting the declination
The declination is the difference between
true north (the direction of the geo-
graphic north pole) and where a com-
pass needle points to. Since the declination
varies from place to place, it needs to be
set for each region. Otherwise the com-
pass will not show the correct direction.
Set the declination by the following steps:NOTE
(1) The declination differs from area to area
and is distributed roughly as shown in
the illustration.
(2) The declination can be set at inter-
vals of 5 degrees, from 20 degrees
west (W20) to 20 degrees east (E20).
D92A060A
When the screen is showing the climate
information press the“ADJ”button to dis-
play the selection buttons. This display will
disappear automatically after about 10 sec-
onds.
1. Press the selection buttons for
“DEV.ADJ.”.
Instruments and controls
4-52Div:
Out put date:

H11A364D
To listen to the radio
EH30B-Fb
1- PWR (On-off) switch
2- VOL (Volume control)knob
3- U/M/L (UKW/MW/LW selection) button
4- Audio adjust button
5- AUDIO button
6- TUNE/SEEK
(Down-step/Down-seek) button
7- TUNE/SEEK
(Up-step/Up-seek) button
8- Memory select buttons
9- Frequency display window
10- Preset memory number display
11- ST (Stereo) indicator
For pleasant driving
6-3
Div:
Out put date:

1. Press the PWR switch (1) to turn on the
radio.
Press the PWR switch again to switch
it off.
2. Press the U/M/L button (3) to select the
desired band (U1/U2/MW/LW).
3. Press the TUNE/SEEK button (6 or 7)
or one of the Memory select buttons (8)
to tune to a station.
Refer to“How to adjust the tune”or
“How to enter frequencies in the
memory”on page 6-5.How to adjust the volumeVOL (Volume control)-2
Turn the VOL knob clockwise to increase
the volume.
H11A348G
Multi centre display
H30B003A
RV meterHow to adjust the tonePress the AUDIO button (5) to select
BASS→TREBLE→FADER→BALANCE
→Audio adjust mode off.
BASS (Bass tone control)
Press the Audio adjust button (4) either
or
to select the desired bass tone
quality.
TREBLE (Treble tone control)
Press the Audio adjust button (4) either
or
to select the desired treble tone
quality.
FADER (Front/rear balance control)
Press the Audio adjust button (4) either
or
to balance the volume of sound
from the front and the rear speakers.
For pleasant driving
6-4Div:
Out put date: