oil filter NISSAN 300ZX 1984 Z31 Maintenance Workshop Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 1984, Model line: 300ZX, Model: NISSAN 300ZX 1984 Z31Pages: 38, PDF Size: 1.19 MB
Page 7 of 38
kmlmils Month
ENGINE ANTI FREEZE- - COOLANT
FRONT WHEEL
BEARING GREASE -
BRAKE FLUID -
DIFFERENTIAL - GEAR OIL
* Maintenance under severe driving condittons
z
tl
:
h)
whsather conditions or in areas where ambient
temperatures are either extremely low or extreme ly high, the filter might becomeclogged In such
, -1 --I-- 4 - -1 - t WINDSHIELD AND REAR
WINDOW WASHER FLUID --
-/---l--]--t-]-- POWERSTEERINGFLUID
w-1 --I- -ENGINE OIL (Except turbocharger engine)
- - @) OIL FILTER
*
--MANUAL TRANSMISSION
--AUTOMATIC
TRANSMISSION
@ Replace at the first 011 change After that. replace 011 filter every second engine 011 change
Page 8 of 38
ENGINE MAINTENANCE
Aw conditioner
compressor
Power steering oil pump
Applied pushing force
Checking Drive Belts
1 Inspect for cracks, fraying, wear or oil adhe-
sion Replace
if necessary
The belts should not touch
the bottom of the
pulley groove.
2
Adjust if belt deflections exceed the limit.
0 VG3OE engine (without turbocharger)
Check drive belt deflections by pushing middle
between pulleys
16 9-11 7-9
10 63) (0 35.0431 (0 28 - 0 351
21 13-16 10-13 (083) (051 -0631 (039-0511
98 N (10 kg. 22 Ibl
Power steering
Alternator pulley
Water pump pulle
SMA777A
VG30ET engine (with turbocharger)
Replacing Air Cleaner Filter-
The viscous paper type air cleaner filter does not
require any cleaning operation between renewals.
SMA779A
Checking Vapor Lines
1. Visually inspect vapor lines for proper attach-
ment, cracks, damage,
loose connections,
chafing and deterioration
2. Check vacuum relief valve for clogging,
sticking, etc
MA-8
Page 11 of 38
ENGINE MAINTENANCE
Changing Engine Oil and Oil Filter
1
2
Warm up engine, and check for oil leakage
from engine components
Change engine
oil and oil filter
Oil capacity:
With oil filter
Without
oil filter
4.0 p (4-1/4 US qt, 3-1/2 Imp qt)
3.3 2 (3-1/2 US qt, 2-7/8 Imp qt)
* Loose" SMA785A 29 - 39 N m (3 0 .4 0 kg-m, 22 . 29 ft-lbl
a. Be careful not to burn yourself as engine oil
is hot.
b. Be sure to clean drain plug and install with
washer.
c. Before installing new oil filter, wipe oil filter
mounting surface
on cylinder block, and
smear
a little engine oil on rubber seal of oil
filter.
d. When installing oil filter, DO NOT use a
wrench to tighten the filter.
Hand-tighten
ONLY
e. Use recommended engine oil.
Start engine Check area around drain plug and
oil filter for any sign of oil leakage.
Run engine for a few minutes, then turn it off
After several minutes, check oil level
Oil'level should be within this range
c---l 011 level should be IO range maintained
SMA786A
MA-I 1
4
Page 36 of 38
SERVICE DATA AND SPECIFICATIONS (S.D.S.)
Used belt deflection
Limit
Adlusted deflecraon
Engine Maintenance
INSPECTION AND ADJUSTMENT
st deflec. TIon Of
new belt Pedal free Play "A"
Alternator
1 -3 IO M -0 121
Arr conditioner I 16 I 9-11 I 7-9 compressor (0631 1035 0431 (028-0351
ADDlted pushtng force I 98 N 110 kg, 22 Ibl
21
10831 Power steering 011 pump
Oil capacity
13.16 10-13
1051 .0631 (039-0511 ~~
unlt P IUS qt. Imp qtl
Wheel alignment IUnladenI
Camber
degree
Caster degree
-35' to 55'
5*50.7"30
Coolant capacity Unlt &? IUS qt. Imp qtl
Wlth 041 falter
Wtthout
001 filter
VG30E & VG30ET
4
0 (4-1 /4, 3-1/21
3 3 13-1/2.
2 7/81
Spark plug
VG30E
I VG30E I VO3OET
105 111-1/8, 91/41
Front wheel turning angle Toe-out turns
Inner wheelIOufer wheel
degree
Plug uaD I 10- 1 1 mm 10039-OW3 in1
22"30'/20'
altitude I 20*2'/650t50 I 20t2'/650f50
standard iype
Hot type
Cola woe
condmon
VG30ET I 20 f 2"/700 f 50 I 20 + 2'/650 t 50
BCPR6ES.11 BCPR6E-11
BCPRSES.11 BCPRSE-11
BCPR7ES.11 BCPR7E-11
TIGHTENING TORQUE
U"lt Nm kg-m ft-lb
Full turns Inner wheel degree
Outer wheel degree
Or1 pan drain plug 29-39 30-40 22-29
Spark plug 20-29 20-30 14-22
Fuel hme clamps 10-15 010-015 07-11
35" .39"
27" .31'
-Chassis and Body Maintenance-
INSPECTION AND ADJUSTMENT
Clutch
Unlt mm 11nI
Pedal height "H" I 195 - 205 I7 68.8 071
Front axle and front suspension
Wheel bearmg preload
IAr measured at wheel hub bolt1 6 86.14 61
With used parts N Ikg, Ibl 1 1 67.7 75 IO 17-079.037- 1741
Kingpin mclination degree I 12'15'- 13'45
degree I 6'- 16
Out 3 (0 0361 - In 3 (0 0361 Side lip IReference datal mm/m lin/ftl
37 5 I1 476) Standard side rod length "A" mm bnl
* On power steering models, wheel turning force la1 circumference
afsteeringwheellof98-147NI10-15kg.22-33lblwith
engtne at idle
Rear axle and rear suspension
Camber degree I -1-55' fa -25
mm (4") I -2 to 2 1-0 08 to 0 081 Toe-,"