ignition NISSAN 350Z 2007 Z33 Audio Visual, Navigation And Telephone System

NAVIGATION SYSTEM
AV-71
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 November2007 350Z
Terminals and Reference Value for Display UnitNKS000D4
Terminal
(Wire color)
ItemSignal
input/
outputCondition
Reference value
(+) (–)Ignition
switchOperation
1 (L/R) Ground RGB signal (R: red) Input ONStart Confirmation/Adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum bar” on
Display Diagnosis screen
2 (L) Ground RGB signal (G: green) Input ONStart Confirmation/Adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum bar” on
Display Diagnosis screen
3 (L/W) Ground RGB signal (B: blue) Input ONStart Confirmation/Adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum bar” on
Display Diagnosis screen
4 — Shield — — — —
7 (B/R) GroundRGB synchronizing
signalInput ON —
8 (W/R) Ground RGB area (YS) signal Input ON — Approx. 5 V
12 (R) GroundCommunication
signal (–)Input/
OutputONOperate navigation system
with NAVI switch
13 (G) GroundCommunication
signal (+)Input/
OutputONOperate navigation system
with NAVI switch
14 — Shield — — — —
SKIB7360E
SKIB7361E
SKIB7362E
SKIB3603E
SKIB7379E
SKIB7378E

AV-72
NAVIGATION SYSTEM
Revision: 2006 November2007 350Z
15 (L) GroundCommunication
signal (–)Input/
OutputONOperate navigation system
with NAVI switch
16 (R) GroundCommunication
signal (+)Input/
OutputONOperate navigation system
with NAVI switch
19 (LG) Ground ACC power supply Input ACC — Battery voltage
21 (Y) Ground Battery power supply Input OFF — Battery voltage
22 (B) Ground Ground — ON — Approx. 0 V
23 (Y) Ground Battery power supply Input OFF — Battery voltage
24 (B) Ground Ground — ON — Approx. 0 VTerminal
(Wire color)
ItemSignal
input/
outputCondition
Reference value
(+) (–)Ignition
switchOperation
SKIB7379E
SKIB7378E

NAVIGATION SYSTEM
AV-73
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 November2007 350Z
Terminals and Reference Value for NAVI SwitchNKS000D5
Terminal
(Wire color)
ItemSignal
input/
outputCondition
Reference value
(+) (–)Ignition
switchOperation
1 (LG) Ground ACC power supply Input ACC — Battery voltage
2 (R/L) Ground Illumination signal Input ONLighting switch ON Approx. 12 V
Lighting switch OFF Approx. 0 V
3 (R/Y) GroundIllumination control
signalInput ONIllumination control switch is
operated by lighting switch
in ON positionChanges between approx. 0 and
approx. 12 V
4 (R) GroundCommunication
signal (+)Input/
OutputONOperate navigation system
with NAVI switch
5 (L) GroundCommunication
signal (–)Input/
OutputONOperate navigation system
with NAVI switch
7 (B) Ground Ground — ON — Approx. 0 V
SKIB7378E
SKIB7379E

AV-74
NAVIGATION SYSTEM
Revision: 2006 November2007 350Z
Special Note for Trouble DiagnosisNKS002JP
Prior to perform trouble diagnosis, make sure there are no corresponding description in the “Example of
Symptoms Possible No Malfunction”. Refer to AV- 9 5 , "
Example of Symptoms Possible No Malfunction" .
On Board Self-Diagnosis FunctionNKS000D6
DESCRIPTION

Trouble diagnosis function of navigation system has a Self Diagnosis mode by automatic operation and a
Confirmation/Adjustment mode by manual operation.

Self Diagnosis mode checks for connections between the units constituting this system, analyzes each
individual unit at the same time, and displays the results on the display unit.

Confirmation/Adjustment mode displays trouble diagnosis that require an operation and a judgment by a
human (auto-decision can not be performed by the system), confirmation of preset value, and an error his-
tory.
DIAGNOSIS ITEM
Self Diagnosis ModeNKS000D7
OPERATION PROCEDURE
1. Start the engine.
2. Press and hold “MAP” and “ ” buttons simultaneously for 5
seconds or more.

Shifting from current screen to previous screen is performed
by pressing “BACK” button.
Mode Description
Self Diagnosis

NAVI control unit diagnosis (DVD-ROM drive will not be diagnosed when no
DVD-ROM is in it.).

Analyzes connection between the NAVI control unit and the GPS antenna, con-
nection between the NAVI control unit and each unit, and operation of each unit.
Confirmation/
AdjustmentDisplay DiagnosisColor tone and shading of the screen can be checked by the display of a color bar
and a gray scale.
Vehicle SignalsDiagnosis of signals that are input to NAVI control unit can be performed for Vehicle
speed, Lights, Ignition and Reverse.
NavigationSteering Angle
AdjustmentThis mode is used to correct difference between actual turning angle of a vehicle
and turning angle of the vehicle mark on the display.
Speed CalibrationUnder ordinary conditions, the navigation system distance measuring function will
automatically compensate for minute decreases in wheel and tire diameter caused
by tire wear or low-pressure. Speed Calibration can immediately restore system
accuracy in cases such as when distance calibration is needed because of the use
of tire chains.
Error HistoryMalfunctions that occurred in the past are displayed, along with the number of times
each has occurred. Time and location when/where the errors occurred are also dis-
played.
Delete Unit Connection Log Erase the connection history of unit and error history.
SKIB7380E

AV-78
NAVIGATION SYSTEM
Revision: 2006 November2007 350Z
DISPLAY DIAGNOSIS

If RGB signal is malfunctioning, the tint of the color bar display is as follows.
VEHICLE SIGNALS
A comparison check can be made of each actual vehicle signal and
the signals recognized by the NAVI control unit.
NOTE:
If ignition signal is NG, each vehicle signal of vehicle speed and reverse is not displayed.
SKIB6976E
R (red) signal error : Light blue (Cyan) tint
G (green) signal error : Purple (Magenta) tint
B (blue) signal error : Yellow tint
SKIB6977E
Diagnosis item Display Condition Remarks
Vehicle speedON When vehicle speed is more than 0 km/h (0 MPH)
Changes in indication may be delayed.
This is normal. OFF When vehicle speed is 0 km/h (0 MPH)
— Ignition switch in ACC position
LightsON Lighting switch ON
—
OFF Lighting switch OFF
IgnitionON Ignition switch ON
—
OFF Ignition switch ACC position
ReverseON Selector lever in R position
Changes in indication may be delayed.
This is normal. OFF Selector lever in any position other than R position
— Ignition switch in ACC position

AV-80
NAVIGATION SYSTEM
Revision: 2006 November2007 350Z
ERROR HISTORY
Diagnosis results of self-diagnosis depend on if any error occurred during the time after selecting “Self Diag-
nosis” until self-diagnosis results is displayed.
Meanwhile, when an error occurs before selecting “Self Diagnosis”, and if an error does not occur until self-
diagnosis results is displayed, a diagnosis result is judged as normal.
Consequently, a diagnosis needs to be performed with “Error History” for the past error that is not available
with self-diagnosis.
“Error History” displays the time and place of the most recent occurrence of that error. However, take note of
the following points.

Correct time of the error occurrence may not be displayed when the GPS antenna substrate within the
NAVI control unit has malfunctioned.

Place of the error occurrence is represented by the position of the vehicle mark at the time when the error
occurred. If the vehicle mark has deviated from the correct position, then the place of the error occurrence
may not be located correctly.

When the ignition switch is turned ON if the error is detected, the counter increases 1. Even if it is normal
when the ignition switch is turned ON the next time, the counter does not decrease.

The upper limit of the counter is 50. 51 or more is displayed as 50. It can be reset to 0 by “Delete log”
switch.
SKIB6978E

NAVIGATION SYSTEM
AV-81
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 November2007 350Z
Diagnosis by Error History

When having a difficulty on the investigation of cause due to multiple errors with a reproducible malfunc-
tion, turn ON the ignition switch from OFF mode after making a memo of the item and number of time (or
delete “Error History”). Check “Error History” again after the malfunction was reproduced, and then per-
form diagnosis focusing on the item of which number of time increased.

DVD-ROM error history may be restored because DVD-ROM cannot be temporarily read. (Driving on
rough road etc.) Then, erase the error history. (This is not a malfunction.) Perform service in “Action to
take” if error history are repeatedly indicated again.
Error item Possible cause Action to take
GPS Antenna ErrorGPS antenna connection malfunction
is detected1. Start self-diagnosis, and make sure of
the result.
2. If any error is found, GO TO 3. If any
error is not found, delete the error his-
tory and end the diagnosis. (This is not
a malfunction.)
3. Check if GPS antenna feeder line is
snapped or pinched.
4. If the results from the above checkup
show no malfunction, replace GPS
antenna, and then restart self-diagno-
sis.
5. If self-diagnosis results still show any
malfunction, replace NAVI control unit.
FLASH-ROM Error Of Control Unit
NAVI control unit malfunction is
detected1. Start self-diagnosis, and make sure of
the result.
2. If any error is found, replace NAVI con-
trol unit. Refer to AV- 9 8 , "
Removal and
Installation of NAVI Control Unit" . If any
error is not found, delete the error his-
tory and end the diagnosis. (This is not
a malfunction.) Connection Of Gyro
GPS Communication Error
GPS malfunction is detectedIf the symptoms such as the GPS receipt
malfunction occur, intermittent malfunc-
tion caused by strong radio interference
may be detected.
If the malfunction always occurs, replace
NAVI control unit. GPS ROM Error
GPS RAM Error
GPS RTC Error
DVD-ROM Mechanism not Detected

Malfunction is detected on DVD-
ROM drive pickup lens in NAVI con-
trol unit

There is dirt and damage on the
DVD-ROM1. Check if the inserted DVD-ROM is
specified for this navigation system,
and the DVD-ROM is dirty, scratched or
warped.
2. If the results from the above checkup
show no malfunction, insert the same
DVD-ROM, and then restart self-diag-
nosis.
3. If self-diagnosis results still show any
malfunction, replace NAVI control unit. DVD-ROM Communication Error
DVD-ROM Mechanism Error
DVD-ROM Focus Error
DVD-ROM TOC Error
DVD-ROM Disc Error
DVD-ROM Seek Error
DVD-ROM Error Correction Error
DVD-ROM Read Error
DVD-ROM Data Transfer Error
DVD-ROM Data Error
DVD-ROM Loading / Eject Error
DVD-ROM Time-out

AV-82
NAVIGATION SYSTEM
Revision: 2006 November2007 350Z
Front Display Connection ErrorDisplay unit power supply and ground
circuit malfunction is detected1. Delete the error history, and turn OFF
ignition switch.
2. Turn ON ignition switch, and make sure
of the error history.
3. If the error item listed left is displayed
again, GO TO 4. If the error item is not
displayed, end the diagnosis. (This is
not a malfunction.)
4. Check display unit power supply and
ground circuit.
5. If the results from the above checkup
show no malfunction, replace display
unit. Error item Possible cause Action to take

NAVIGATION SYSTEM
AV-83
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 November2007 350Z
DELETE UNIT CONNECTION LOG
Erase the connection history of unit and error history that is recorded
in NAVI control unit (clear the connection history of the removed
unit).
Switches Connection Error

NAVI switch power supply and
ground circuit malfunction is
detected

Malfunction is detected on commu-
nication signal between display unit
and NAVI switch

Malfunction is detected on commu-
nication signal between NAVI con-
trol unit and display unit1. Delete the error history, and turn OFF
ignition switch.
2. Turn ON ignition switch, and make sure
of the error history.
3. If the error item listed left is displayed
again, GO TO 4. If the error item is not
displayed, end the diagnosis. (This is
not a malfunction.)
4. Check NAVI switch power supply and
ground circuit.
5. Check communication circuit between
display unit and NAVI switch.
6. Check communication circuit between
NAVI control unit and display unit.
7. If the results from the above checkup
show no malfunction, replace NAVI
switch, display unit, or NAVI control
unit, and then start self-diagnosis.
8. If self-diagnosis results still show any
malfunction, replace one of the two
units that is not replaced yet.
9. If self-diagnosis results still show any
malfunction, replace the other unit.

Front Display Connection Error

Switches Connection Error

Malfunction is detected on commu-
nication signal between NAVI con-
trol unit and display unit

Malfunction is detected on commu-
nication signal between display unit
and NAVI switch1. Delete the error history, and turn OFF
ignition switch.
2. Turn ON ignition switch, and make sure
of the error history.
3. If the error item listed left is displayed
again, GO TO 4. If the error item is not
displayed, end the diagnosis. (This is
not a malfunction.)
4. Check communication circuit between
NAVI control unit and display unit.
5. Check communication circuit between
display unit and NAVI switch.
6. If the results from the above checkup
show no malfunction, replace NAVI
switch, display unit, or NAVI control
unit, and then start self-diagnosis.
7. If self-diagnosis results still show any
malfunction, replace one of the two
units that is not replaced yet.
8. If self-diagnosis results still show any
malfunction, replace the other unit. Error item Possible cause Action to take
SKIB6979E

AV-84
NAVIGATION SYSTEM
Revision: 2006 November2007 350Z
All Images Are Not DisplayedNKS000DI
Symptom: RGB image such as a map screen is not displayed.
1. CHECK CONDITION
Check if brightness of screen changes when button on NAVI switch is turned on after turning on ignition
switch.
Does brightness of screen change?
YES >> GO TO 5.
NO >> GO TO 2.
2. CHECK NAVI CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT
1. Check voltage between NAVI control unit harness connector ter-
minals and ground.
2. Turn ignition switch OFF.
3. Disconnect NAVI control unit connector.
4. Check continuity between NAVI control unit harness connector
B104 terminal 1 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
Terminals
OFF ACC ON (+)
(–)
Connector Terminal
B1042
GroundBattery
voltageBattery
voltageBattery
voltage
50 VBattery
voltageBattery
voltage
1 – Ground : Continuity should exist.
SKIB7018E
SKIB7019E