AUX NISSAN 350Z 2007 Z33 Automatic Air Conditioner Workshop Manual

ATC-2Revision: 2006 November2007 350Z WORK FLOW ...................................................... 34
SYMPTOM TABLE .............................................. 34
Component Parts and Harness Connector Location ... 35
ENGINE COMPARTMENT .................................. 35
PASSENGER COMPARTMENT .......................... 36
Schematic ............................................................... 37
Wiring Diagram — A/C — ....................................... 38
Auto Amp. Terminals and Reference Value ............ 43
PIN CONNECTOR TERMINAL LAYOUT ............ 43
TERMINALS AND REFERENCE VALUE FOR
UNIFIED METER AND A/C AMP. ........................ 43
Self-diagnosis Function .......................................... 45
DESCRIPTION .................................................... 45
FUNCTION CONFIRMATION PROCEDURE ...... 46
AUXILIARY MECHANISM: TEMPERATURE
SETTING TRIMMER ........................................... 50
AUXILIARY MECHANISM: FOOT POSITION
SETTING TRIMMER ........................................... 51
AUXILIARY MECHANISM: INLET PORT MEM-
ORY FUNCTION ................................................. 51
Operational Check .................................................. 53
CHECKING BLOWER ......................................... 53
CHECKING DISCHARGE AIR ............................ 53
CHECKING INTAKE DOOR ................................ 53
CHECKING TEMPERATURE DECREASE ......... 53
CHECKING TEMPERATURE INCREASE .......... 53
CHECKING A/C SWITCH ................................... 53
Power Supply and Ground Circuit for Auto Amp. ... 54
INSPECTION FLOW ........................................... 54
COMPONENT DESCRIPTION ............................ 54
DIAGNOSIS PROCEDURE FOR A/C SYSTEM ... 55
LAN System Circuit ................................................ 56
DIAGNOSIS PROCEDURE FOR LAN CIRCUIT ... 56
Mode Door Motor Circuit ........................................ 60
INSPECTION FLOW ........................................... 60
SYSTEM DESCRIPTION .................................... 61
COMPONENT DESCRIPTION ............................ 62
DIAGNOSIS PROCEDURE FOR MODE DOOR
MOTOR ............................................................... 62
Air Mix Door Motor Circuit ...................................... 63
INSPECTION FLOW ........................................... 63
SYSTEM DESCRIPTION .................................... 64
COMPONENT DESCRIPTION ............................ 65
DIAGNOSIS PROCEDURE FOR AIR MIX DOOR ... 65
Air Mix Door Motor PBR Circuit .............................. 65
DIAGNOSIS PROCEDURE FOR AIR MIX DOOR
MOTOR PBR ....................................................... 65
Intake Door Motor Circuit ........................................ 66
INSPECTION FLOW ........................................... 66
SYSTEM DESCRIPTION .................................... 67
COMPONENT DESCRIPTION ............................ 68
DIAGNOSIS PROCEDURE FOR INTAKE DOOR
MOTOR ............................................................... 68
Blower Motor Circuit ............................................... 69
INSPECTION FLOW ........................................... 69
SYSTEM DESCRIPTION .................................... 70
COMPONENT DESCRIPTION ............................ 71
DIAGNOSIS PROCEDURE FOR BLOWER
MOTOR ............................................................... 71COMPONENT INSPECTION ............................... 73
Magnet Clutch Circuit .............................................. 74
INSPECTION FLOW ............................................ 74
SYSTEM DESCRIPTION ..................................... 75
DIAGNOSIS PROCEDURE FOR MAGNET
CLUTCH .............................................................. 75
COMPONENT INSPECTION ............................... 80
Insufficient Cooling .................................................. 81
INSPECTION FLOW ............................................ 81
PERFORMANCE TEST DIAGNOSIS .................. 83
PERFORMANCE CHART .................................... 85
TROUBLE DIAGNOSIS FOR UNUSUAL PRES-
SURE ................................................................... 86
Insufficient Heating ................................................. 89
INSPECTION FLOW ............................................ 89
Noise ....................................................................... 90
INSPECTION FLOW ............................................ 90
Self-diagnosis ......................................................... 91
INSPECTION FLOW ............................................ 91
Ambient Sensor Circuit ........................................... 92
COMPONENT DESCRIPTION ............................ 92
AMBIENT TEMPERATURE INPUT PROCESS ... 92
DIAGNOSIS PROCEDURE FOR AMBIENT
SENSOR .............................................................. 92
COMPONENT INSPECTION ............................... 94
In-vehicle Sensor Circuit ......................................... 94
COMPONENT DESCRIPTION ............................ 94
DIAGNOSIS PROCEDURE FOR IN-VEHICLE
SENSOR .............................................................. 95
COMPONENT INSPECTION ............................... 96
Sunload Sensor Circuit ........................................... 97
COMPONENT DESCRIPTION ............................ 97
SUNLOAD INPUT PROCESS ............................. 97
DIAGNOSIS PROCEDURE FOR SUNLOAD
SENSOR .............................................................. 97
COMPONENT INSPECTION ............................... 99
Intake Sensor Circuit .............................................100
COMPONENT DESCRIPTION ..........................100
DIAGNOSIS PROCEDURE FOR INTAKE SEN-
SOR ...................................................................100
COMPONENT INSPECTION .............................101
A/C CONTROLLER .................................................102
Removal and Installation .......................................102
REMOVAL ..........................................................102
INSTALLATION ..................................................102
Disassembly and Assembly ..................................102
AUTO AMP ..............................................................103
Removal and Installation of Unified Meter and A/C
Amp. ......................................................................103
REMOVAL ..........................................................103
INSTALLATION ..................................................103
AMBIENT SENSOR ................................................104
Removal and Installation .......................................104
REMOVAL ..........................................................104
INSTALLATION ..................................................104
IN-VEHICLE SENSOR ............................................105
Removal and Installation .......................................105
REMOVAL ..........................................................105
INSTALLATION ..................................................105

TROUBLE DIAGNOSIS
ATC-45
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2006 November2007 350Z
Self-diagnosis FunctionNJS0000W
DESCRIPTION
The self-diagnosis system diagnoses sensors, door motors, blower motor, etc. by system line.
Self-diagnosis is STEP-1 to 7. There are two ways of changing method during self-diagnosis.

Switching to self-diagnosis STEP-1 to 4.
Shifting from normal control to the self-diagnosis system is accomplished by starting the engine (turning
the ignition switch from OFF to ON) and pressing A/C switch for at least 5 seconds. The A/C switch must
be pressed within 10 seconds after starting the engine (ignition switch is turned ON). This system will be
canceled by either pressing intake switch or turning the ignition switch OFF. Shifting to the next step is
accomplished by means of turning fan control dial, as required.

Switching to self-diagnosis STEP-5 to 7 (Auxiliary mechanism).
Shifting from normal control to the self-diagnosis system is accomplished by starting the engine (turning
the ignition switch from OFF to ON) and pressing intake switch for at least 5 seconds. The intake switch
must be pressed within 10 seconds after starting the engine (ignition switch is turned ON). This system
will be canceled by either pressing A/C switch or turning the ignition switch OFF. Shifting to the next step
is accomplished by means of turning fan control dial, as required.
SJIA1139E

ATC-48
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
8. CHECK ACTUATORS
Refer to the following chart and confirm discharge air flow, air tem-
perature, blower motor duty ratio and compressor operation.
Checks must be made visually, by listening the sound, or by touching air outlets with hand, etc. for improper
operation.
*1: STEP-No. 41 to 46 are for differentiation and will not be displayed.
*2: FOOT position during automatic control. Refer to AT C - 5 1 , "
AUXILIARY MECHANISM: FOOT POSITION
SETTING TRIMMER" .
OK or NG
OK >> 1. Turn ignition switch OFF or intake switch ON.
2. INSPECTION END
NG >>

Air outlet does not change.
Go to Mode Door Motor Circuit. Refer to AT C - 6 0 , "
Mode Door Motor Circuit" .

Intake door does not change.
Go to Intake Door Motor Circuit. Refer to AT C - 6 6 , "
Intake Door Motor Circuit" .

Discharge air temperature does not change.
Go to Air Mix Door Motor Circuit. Refer to AT C - 6 3 , "
Air Mix Door Motor Circuit" .

Blower motor operation is malfunctioning.
Go to Blower Motor Circuit. Refer to AT C - 6 9 , "
Blower Motor Circuit" .

Magnet clutch does not engage.
Go to Magnet Clutch Circuit. Refer to AT C - 7 4 , "
Magnet Clutch Circuit" .
RJIA2110E
STEP-No. *1STEP-41 STEP-42 STEP-43 STEP-44 STEP-45 STEP-46
Mode control dial posi-
tionAUTO VENT B/LFOOT or
FOOT2D/F or D/F2 DEF
Mode door position VENT VENT2 B/L
FOOT
*2D/F DEF
Intake door position REC REC REC FRE FRE FRE
Air mix door position FULL COLD FULL COLD FULL COLD FULL HOT FULL HOT FULL HOT
Blower motor duty ratio 25% 25% 41% 57% 75% 91%
Compressor ON ON OFF OFF ON ON

ATC-50
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
AUXILIARY MECHANISM: TEMPERATURE SETTING TRIMMER
The trimmer compensates for differences in range of ±3°C (±6°F) between temperature setting (temperature
control dial position) and temperature felt by customer.
Operating procedures for this trimmer are as follows:
1. Set fan control dial to OFF.
2. Turn ignition switch ON.
3. Set in self-diagnosis mode as follows. Within 10 seconds after starting engine (ignition switch is turned
ON.), press intake switch for at least 5 seconds.
4. When intake switch is pressed, temperature shifts in following order: 0°C (0°F)→ 1°C (2°F)→ 2°C (4°F)→
3°C (6°F)→ −3°C (−6°F)→ −2°C (−4°F)→ −1°C (−2°F)→ return to 0°C (0°F).
When battery cable is disconnected or battery voltage is below 9 V, trimmer operation is canceled. Tempera-
ture set becomes that of initial condition, i.e. 0°C (0°F).
Setting temperatureLED status of each switch
FRE REC A/C
−3°C (−6°F) ON ON ON
−2°C (−4°F) ON ON OFF
−1°C (−2°F) ON OFF ON
0°C (0°F) (Initial setting) OFF OFF OFF
1°C (2°F) OFF OFF ON
2°C (4°F) OFF ON OFF
3°C (6°F) OFF ON ON

TROUBLE DIAGNOSIS
ATC-51
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2006 November2007 350Z
AUXILIARY MECHANISM: FOOT POSITION SETTING TRIMMER
Wind distribution ratio in FOOT mode can be set.
Operating procedures for this trimmer are as follows:
1. Set fan control dial to AUTO.
2. Turn ignition switch ON.
3. Set in self-diagnosis mode as follows. Within 10 seconds after starting engine (ignition switch is turned
ON.), press intake switch for at least 5 seconds.
4. Press intake switch as desired.
When battery cable is disconnected or battery voltage is below 9 V, trimmer operation is canceled. Wind distri-
bution ratio set becomes that of initial condition.
AUXILIARY MECHANISM: INLET PORT MEMORY FUNCTION
When ignition switch is turned from OFF to ON, inlet port memory function at manual mode can be set.
Operating procedures for this trimmer are as follows:
1. Set fan control dial to 1st - 12th speed.
2. Turn ignition switch ON.
3. Set in self-diagnosis mode as follows. Within 10 seconds after starting engine (ignition switch is turned
ON.), press intake switch for at least 5 seconds.
4. Press intake switch as desired.
RJIA1365E
Ty p eLED status of each switch
FRE REC A/C
Type-A (Initial setting) OFF OFF ON
Ty p e - B O F F O N O F F
Type-C OFF ON ON
Type-D ON OFF OFF
LED status of
FRE positionLED status of
REC positionSetting status
Setting changeover
method
FRE REC
OFF OFF AUTO control AUTO control
Intake SW: ON OFF ON AUTO control (Initial setting)Manual REC status is memorized.
(Initial setting)
ON ON Manual FRE status is memorized. AUTO control
ON OFF Manual FRE status is memorized. Manual REC status is memorized.

ATC-82
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
*1ATC-46, "FUNCTION CONFIRMA-
TION PROCEDURE", see No. 1.*2AT C - 6 3 , "
Air Mix Door Motor Circuit"*3AT C - 8 5 , "Test Reading"
*4ATC-50, "AUXILIARY MECHA-
NISM: TEMPERATURE SETTING
TRIMMER"
*5AT C - 4 6 , "FUNCTION CONFIRMA-
TION PROCEDURE", see No. 9.*6AT C - 5 6 , "
LAN System Circuit"
*7ATC-69, "Blower Motor Circuit"*8AT C - 7 4 , "Magnet Clutch Circuit"*9AT C - 8 3 , "PERFORMANCE TEST
DIAGNOSIS"
*10ATC-53, "Operational Check"*11AT C - 4 6 , "FUNCTION CONFIRMA-
TION PROCEDURE", see No. 5 to
7.*12AT C - 5 , "
CONTAMINATED REFRIG-
ERANT"
*13EM-12, "Checking Drive Belts"*14EC-543, "SYSTEM DESCRIPTION"