wiring NISSAN 350Z 2007 Z33 Automatic Air Conditioner Workshop Manual

ATC-2Revision: 2006 November2007 350Z WORK FLOW ...................................................... 34
SYMPTOM TABLE .............................................. 34
Component Parts and Harness Connector Location ... 35
ENGINE COMPARTMENT .................................. 35
PASSENGER COMPARTMENT .......................... 36
Schematic ............................................................... 37
Wiring Diagram — A/C — ....................................... 38
Auto Amp. Terminals and Reference Value ............ 43
PIN CONNECTOR TERMINAL LAYOUT ............ 43
TERMINALS AND REFERENCE VALUE FOR
UNIFIED METER AND A/C AMP. ........................ 43
Self-diagnosis Function .......................................... 45
DESCRIPTION .................................................... 45
FUNCTION CONFIRMATION PROCEDURE ...... 46
AUXILIARY MECHANISM: TEMPERATURE
SETTING TRIMMER ........................................... 50
AUXILIARY MECHANISM: FOOT POSITION
SETTING TRIMMER ........................................... 51
AUXILIARY MECHANISM: INLET PORT MEM-
ORY FUNCTION ................................................. 51
Operational Check .................................................. 53
CHECKING BLOWER ......................................... 53
CHECKING DISCHARGE AIR ............................ 53
CHECKING INTAKE DOOR ................................ 53
CHECKING TEMPERATURE DECREASE ......... 53
CHECKING TEMPERATURE INCREASE .......... 53
CHECKING A/C SWITCH ................................... 53
Power Supply and Ground Circuit for Auto Amp. ... 54
INSPECTION FLOW ........................................... 54
COMPONENT DESCRIPTION ............................ 54
DIAGNOSIS PROCEDURE FOR A/C SYSTEM ... 55
LAN System Circuit ................................................ 56
DIAGNOSIS PROCEDURE FOR LAN CIRCUIT ... 56
Mode Door Motor Circuit ........................................ 60
INSPECTION FLOW ........................................... 60
SYSTEM DESCRIPTION .................................... 61
COMPONENT DESCRIPTION ............................ 62
DIAGNOSIS PROCEDURE FOR MODE DOOR
MOTOR ............................................................... 62
Air Mix Door Motor Circuit ...................................... 63
INSPECTION FLOW ........................................... 63
SYSTEM DESCRIPTION .................................... 64
COMPONENT DESCRIPTION ............................ 65
DIAGNOSIS PROCEDURE FOR AIR MIX DOOR ... 65
Air Mix Door Motor PBR Circuit .............................. 65
DIAGNOSIS PROCEDURE FOR AIR MIX DOOR
MOTOR PBR ....................................................... 65
Intake Door Motor Circuit ........................................ 66
INSPECTION FLOW ........................................... 66
SYSTEM DESCRIPTION .................................... 67
COMPONENT DESCRIPTION ............................ 68
DIAGNOSIS PROCEDURE FOR INTAKE DOOR
MOTOR ............................................................... 68
Blower Motor Circuit ............................................... 69
INSPECTION FLOW ........................................... 69
SYSTEM DESCRIPTION .................................... 70
COMPONENT DESCRIPTION ............................ 71
DIAGNOSIS PROCEDURE FOR BLOWER
MOTOR ............................................................... 71COMPONENT INSPECTION ............................... 73
Magnet Clutch Circuit .............................................. 74
INSPECTION FLOW ............................................ 74
SYSTEM DESCRIPTION ..................................... 75
DIAGNOSIS PROCEDURE FOR MAGNET
CLUTCH .............................................................. 75
COMPONENT INSPECTION ............................... 80
Insufficient Cooling .................................................. 81
INSPECTION FLOW ............................................ 81
PERFORMANCE TEST DIAGNOSIS .................. 83
PERFORMANCE CHART .................................... 85
TROUBLE DIAGNOSIS FOR UNUSUAL PRES-
SURE ................................................................... 86
Insufficient Heating ................................................. 89
INSPECTION FLOW ............................................ 89
Noise ....................................................................... 90
INSPECTION FLOW ............................................ 90
Self-diagnosis ......................................................... 91
INSPECTION FLOW ............................................ 91
Ambient Sensor Circuit ........................................... 92
COMPONENT DESCRIPTION ............................ 92
AMBIENT TEMPERATURE INPUT PROCESS ... 92
DIAGNOSIS PROCEDURE FOR AMBIENT
SENSOR .............................................................. 92
COMPONENT INSPECTION ............................... 94
In-vehicle Sensor Circuit ......................................... 94
COMPONENT DESCRIPTION ............................ 94
DIAGNOSIS PROCEDURE FOR IN-VEHICLE
SENSOR .............................................................. 95
COMPONENT INSPECTION ............................... 96
Sunload Sensor Circuit ........................................... 97
COMPONENT DESCRIPTION ............................ 97
SUNLOAD INPUT PROCESS ............................. 97
DIAGNOSIS PROCEDURE FOR SUNLOAD
SENSOR .............................................................. 97
COMPONENT INSPECTION ............................... 99
Intake Sensor Circuit .............................................100
COMPONENT DESCRIPTION ..........................100
DIAGNOSIS PROCEDURE FOR INTAKE SEN-
SOR ...................................................................100
COMPONENT INSPECTION .............................101
A/C CONTROLLER .................................................102
Removal and Installation .......................................102
REMOVAL ..........................................................102
INSTALLATION ..................................................102
Disassembly and Assembly ..................................102
AUTO AMP ..............................................................103
Removal and Installation of Unified Meter and A/C
Amp. ......................................................................103
REMOVAL ..........................................................103
INSTALLATION ..................................................103
AMBIENT SENSOR ................................................104
Removal and Installation .......................................104
REMOVAL ..........................................................104
INSTALLATION ..................................................104
IN-VEHICLE SENSOR ............................................105
Removal and Installation .......................................105
REMOVAL ..........................................................105
INSTALLATION ..................................................105

ATC-4
PRECAUTIONS
Revision: 2006 November2007 350Z
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NJS000D2
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Battery ServiceNJS000D3
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Precautions for Procedures without Cowl Top CoverNJS000CP
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
PIIB3706J

ATC-32
AIR CONDITIONER CONTROL
Revision: 2006 November2007 350Z
CAN Communication System DescriptionNJS0000P
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only. For details, refer to LAN-48,
"CAN System Specification Chart" .

ATC-38
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
Wiring Diagram — A/C —NJS0000U
TJWT0092E