Trunk lid NISSAN 350Z 2007 Z33 Body, Lock And Security System Owner's Guide

TRUNK LID OPENER
BL-123
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
11 . CHECK DRIVER SIDE DOOR LOCK ACTUATOR GROUND CIRCUIT
Check continuity between driver side door lock actuator switch har-
ness connector D11 terminal 4 and ground.
OK or NG
OK >> Replace driver side door lock actuator.
NG >> Repair harness or connector.
TRUNK DOSE NOT CLOSE
1. CHECK TRUNK LID OPEN INPUT SIGNAL
1. Remove Key from ignition key cylinder.
2. Turn on trunk lid opener cancel switch.
3. Unlock driver side door.
4. Check voltage between BCM and ground.
OK or NG
OK >> GO TO 2.
NG >> Replace BCM.
2. CHECK TRUNK LID OPENER CANCEL SWITCH
1. Disconnect trunk lid opener cancel switch.
2. Check continuity between trunk lid opener cancel switch har-
ness connector B71 terminals 1 and 2.
OK or NG
OK >> GO TO 3.
NG >> Replace trunk lid opener cancel switch.4 (B) - ground : Continuity should exist.
PIIA7876E
ConnectorTerminal
(Wire color)
ConditionVoltage (V)
(Approx.)
(+) (–)
M90 30 (P) GroundTrunk lid opener switch ON 0
Trunk lid opener switch OFF 5
PIIB1269E
TerminalsTrunk lid opener cancel
switch conditionContinuity
12ON Yes
OFF No
PIIA7871E

BL-124
TRUNK LID OPENER
Revision: 2006 November2007 350Z
3. CHECK TRUNK LID OPENER SWITCH
1. Disconnect trunk lid opener switch
2. Check continuity between trunk lid opener switch harness con-
nector T103 terminals 1 and 2.
OK or NG
OK >> GO TO 4.
NG >> Replace trunk lid opener switch.
4. CHECK TRUNK LID OPENER CANCEL SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector M90 terminal
30 and ground.
OK or NG
OK >> GO TO 5.
NG >> Repair harness or connector.
5. CHECK TRUNK LID OPENER SWITCH CIRCUIT
Check continuity between trunk lid opener cancel switch harness
connector B71 terminal 2 and ground.
OK or NG
OK >> GO TO 6.
NG >> Repair harness or connector.
6. CHECK DRIVER SIDE DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect driver side door lock actuator connector.
2. Check continuity between trunk lid opener switch harness con-
nector T103 terminal 2 and ground.
OK or NG
OK >> Replace BCM.
NG >> Repair harness or connector.
Te r m i n a l sTrunk lid opener switch
conditionContinuity
12ON (Pushed) Yes
OFF (Released) No
PIIA7872E
30 (P) - ground : Continuity should not exist.
PIIB1273E
2 (R/Y) - ground : Continuity should not exist.
PIIA8096E
2 (G) - ground : Continuity should not exist.
PIIA8097E

VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-127
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
2. Disconnecting and connecting the battery connector before canceling armed phase.
POWER SUPPLY AND GROUND
Power is supplied at all times

through 10A fuse [No.19, located in the fuse block (J/B)]

to security indicator lamp terminal 1.
Power is supplied at all times

through 40A fusible link (letter F , located in the fuse and fusible link box)

to BCM terminal 55

through 10A fuse [No.18, located in the fuse block (J/B)]

to BCM terminal 42.
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 6, located in the fuse block (J/B)]

to BCM terminal 11.
Ground is supplied.

to BCM terminal 52

through body grounds M30 and M66.
INITIAL CONDITION TO ACTIVATE THE SYSTEM
The operation of the vehicle security system is controlled by the doors and trunk (for Roadster).
To activate the vehicle security system, BCM must receive signals indicating the doors and trunk (for Road-
ster) are closed and the doors are locked by key or key fob.
When a door is open, BCM terminals 12, 65 receives a ground signal from each door switch.
When driver side door is unlocked by power window main switch (door lock and unlock switch), BCM terminal
22 receives a signal from terminal 12 of power window main switch.
When passenger side door is unlocked by power window sub-switch (door lock and unlock switch), BCM ter-
minal 22 receives a signal from terminal 16 of power window sub-switch.
The IPDM E/R then sends a signal to the BCM via CAN communication line.
When the back door (for Coupe) or trunk (for Roadster) is open, BCM terminal 57 (for Roadster) or 58 (for
Coupe) receives a ground signal

from terminal 1 of the back door switch (for Coupe) or terminal 3 of trunk lid lock assembly (trunk room
lamp switch) (for Roadster)

through body grounds B5, B6,T14, D105 (for Coupe) or B5, B6, T14 (for Roadster).
VEHICLE SECURITY SYSTEM ALARM OPERATION
The vehicle security system is triggered by

opening a driver or passenger side door

opening the back door (for Coupe)

opening the trunk (for Roadster)

detection of battery disconnect and connect.
The vehicle security system will be triggered once the system is in armed phase,
When BCM receives a ground signal at terminals 12, 62 (door switch), 57 (trunk room lamp switch) or 58 (back
door switch).
Power is supplied at all times

to horn relay terminal 2

through 15A fuse (No. 35, located in the fuse and fusible link box).
When the vehicle security system is triggered, ground is supplied intermittently to both headlamp relay and
horn relay.
When both headlamp relay (with built-in IPDM E/R) and horn relay are energized and then power is supplied
to headlamps (high beam and low beam) and horns (HIGH and LOW).
The headlamps flash and the horn sounds intermittently.
The alarm automatically turns off after 50 seconds, but will reactivate if the vehicle is tampered with again.
VEHICLE SECURITY SYSTEM DEACTIVATION
To deactivate the vehicle security system, a door must be unlocked or back door (for Coupe) or trunk (for
Roadster) must be opened with the key or key fob.

VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-137
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
Terminals and Reference Value for IPDM E/RNIS0002Z
CONSULT-III Function (BCM)NIS00030
CONSULT-III APPLICATION ITEM
Work Support
Data Monitor
Active Test
Terminal Wire
colorItemSignal
Input/
OutputConditionVoltage [V]
(Approx.)
38 B Ground — — 0
48 L CAN-HInput/
Output——
49 P CAN-LInput/
Output——
51 G/B Horn relay Output ON → OFF 0 → Battery voltage
60 B Ground — — 0
Test Item Description
SECURITY ALARM SET This mode is able to confirm and change security alarm ON-OFF setting.
THEFT ALM TRGThe switch which triggered vehicle security alarm is recorded. This mode is able to confirm and
erase the record of vehicle security alarm. The trigger data can be erased by touching “CLEAR”
on CONSULT-III screen.
Monitored Item Description
IGN ON SW Indicates [ON/OFF] condition of ignition switch.
ACC ON SW Indicates [ON/OFF] condition of ignition switch in ACC position.
KEY CYL LK SW Indicates [ON/OFF] condition of lock signal from key cylinder switch.
KEY CYL UN SW Indicates [ON/OFF] condition of unlock signal from key cylinder switch.
DOOR SW-DR Indicates [ON/OFF] condition of driver side door switch.
DOOR SW-AS Indicates [ON/OFF] condition of passenger side door switch.
BACK DOOR SW Indicates [ON/OFF] condition of back door switch.
TRUNK OPNR SW Indicates [ON/OFF] condition of trunk room lamp switch. (Roadster models)
TRUNK OPN MNTRThis is displayed even when it is not equipped.
Indicates [ON/OFF] condition of trunk lid opener switch. (Roadster models)
TRUNK KEY SW This is displayed even when it is not equipped.
DOOR SW-RR This is displayed even when it is not equipped.
HOOD SW Indicates [ON/OFF] condition of hood switch.
LOCK SW DR/ASIndicates [ON/OFF] condition of lock signal from driver and passenger side door lock/unlock
switch.
UNLK SW DR/ASIndicates [ON/OFF] condition of unlock signal from driver and passenger side door lock/unlock
switch.
LK BUTTON/SIG Indicates [ON/OFF] condition of lock signal from key fob.
UN BUTTON/SIG Indicates [ON/OFF] condition of unlock signal from key fob.
TRUNK BTN/SIGIndicate [ON/OFF] condition of back door open signal from key fob (for Coupe).
Indicates [ON/OFF] condition of trunk open signal from key fob (for Roadster).
Test Item Description
THEFT INDThis test is able to check security indicator lamp operation. The lamp will be turned on when “ON”
on CONSULT-III screen is touched.

VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-141
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
Diagnostic Procedure 1NIS00035
1 – 1 CHECK DOOR SWITCH
Check driver side door switch and passenger side door switch
1. CHECK DOOR SWITCH INPUT SIGNAL
With CONSULT-III
Check door switches (“DOOR SW-DR” and “DOOR SW-AS”) in “DATA MONITOR” mode with CONSULT-III.
Without CONSULT-III
Check voltage between BCM connector and ground.
OK or NG
OK >> Door switch is OK, and go to the following

BL-143, "1 – 2 CHECK BACK DOOR SWITCH
(COUPE)"

BL-145, "1 – 3 CHECK TRUNK LID LOCK ASSEM-
BLY (TRUNK ROOM LAMP SWITCH) (ROADSTER)"
NG >> GO TO 2.
Monitor item Condition
DOOR SW-DROPEN : ON
CLOSE : OFF
DOOR SW-ASOPEN : ON
CLOSE : OFF
ItemCon-
nectorTe r m i n a l
(Wire color)Condi-
tion of
door
switchVoltage [V]
(Approx.)
(+) (–)
Driver side door
switchB83 62 (L)
GroundOpen 0
Close 5
Passenger side
door switchM90 12 (P)Open 0
Close 5
PIIA9539E

VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-145
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
1 – 3 CHECK TRUNK LID LOCK ASSEMBLY (TRUNK ROOM LAMP SWITCH) (ROADSTER)
1. CHECK TRUNK ROOM LAMP SWITCH INPUT SIGNAL
With CONSULT-III
Check trunk lid opener switch (“TRUNK OPN MNTR”) in “DATA MONITOR” mode with CONSULT-III.
Without CONSULT-III
Check voltage between BCM connector and ground.
*: When interior lamp battery saver control is in OFF. → Approx 5V.
OK or NG
OK >> Trunk room lamp switch is OK .
NG >> GO TO 2.
2. CHECK TRUNK LID LOCK ASSEMBLY (TRUNK ROOM LAMP SWITCH) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect trunk lid lock assembly (trunk room lamp switch) and BCM connector.
3. Check continuity between trunk lid lock assembly (trunk room
lamp switch) harness connector T47 terminal 3 and BCM har-
ness connector B83 terminal 57.
4. Check continuity between BCM harness connector B83 terminal
57 and ground.
OK or NG
OK >> GO TO 3.
NG >> Replace trunk lid lock assembly (trunk room lamp
switch) harness.
3. CHECK TRUNK LID LOCK ASSEMBLY (TRUNK ROOM LAMP SWITCH) GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between trunk lid lock assembly (trunk room
lamp switch) harness connector T47 terminal 1 and ground.
OK or NG
OK >> Trunk lid lock assembly (trunk room lamp switch) is OK.
NG >> Repair or replace trunk lid lock assembly (trunk room
lamp switch) harness.
Monitor item Condition
TRNK OPN MNTROPEN : ON
CLOSE : OFF
ConnectorTerminal (Wire color)
Condition of trunk
room lamp switchVoltage [V]
(Approx.)
(+) (–)
B83 57 (R/W) GroundOpen 0
Close Battery voltage*
PIIB1266E
57 (R/W) - 3 (R/W) : Continuity should exist.
57 (R/W) - Ground : Continuity should not exist.
PIIB9170E
1 (B) - Ground : Continuity should exist.
PIIB9171E

BODY REPAIR
BL-171
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
Body Exterior Paint Color (Roadster)NIS0003U
2S: Solid + Clear, M: Metallic, 2P: 2-Coat pearl, 3P: 3-Coat pearl, CPM: Clear pearl metallic, RP: Multi flex color
SIIA2295E
ComponentColor code BA17 BAX6 BB17 BG41 BK23 BL40 BQX1 BWV2
DescriptionOrang
eRed Blue Black SilverRed
PurpleWhite Silver
Paint type 2P 2S CPM 2P M RP 3P M
Hard clear coat - X X X - X - -
1 Bumper fascia Body color BA17 BAX6 BB17 BG41 BK23 BL40 BQX1 BWV2
2Front pillar
finisherBody color BA17 BAX6 BB17 BG41 BK23 BL40 BQX1 BWV2
3Door outside
mirrorCase Body color BA17 BAX6 BB17 BG41 BK23 BL40 BQX1 BWV2
Base Body color BA17 BAX6 BB17 BG41 BK23 BL40 BQX1 BWV2
4Center mud-
guardBody color BA17 BAX6 BB17 BG41 BK23 BL40 BQX1 BWV2
5Door outside
handle and
escutcheonVelour chro-
mium-plateCr2p Cr2p Cr2p Cr2p Cr2p Cr2p Cr2p Cr2p
6 Fuel filler lid Body color BA17 BAX6 BB17 BG41 BK23 BL40 BQX1 BWV2
7 Storage lid Body color BA17 BAX6 BB17 BG41 BK23 BL40 BQX1 BWV2
8 Trunk lid Body color BA17 BAX6 BB17 BG41 BK23 BL40 BQX1 BWV2