engine NISSAN 350Z 2007 Z33 Engine Mechanical Manual PDF

NISSAN 350Z 2007 Z33 Engine Mechanical Manual PDF 350Z 2007 Z33 NISSAN NISSAN https://www.carmanualsonline.info/img/5/765/w960_765-0.png NISSAN 350Z 2007 Z33 Engine Mechanical Manual PDF

Page 106 of 148

NISSAN 350Z 2007 Z33 Engine Mechanical Manual PDF EM-106
ENGINE ASSEMBLY
Revision: 2006 November2007 350Z
INSPECTION AFTER INSTALLATION
Inspection for Leaks
The following are procedures for checking fluids leak, lubricates leak and exhaust gases leak

Page 108 of 148

NISSAN 350Z 2007 Z33 Engine Mechanical Manual PDF EM-108
CYLINDER BLOCK
Revision: 2006 November2007 350Z
DISASSEMBLY
1. Remove engine assembly from vehicle, and separate front suspension member and transmission from
engine. Refer to EM-101, "
ENGINE

Page 109 of 148

NISSAN 350Z 2007 Z33 Engine Mechanical Manual PDF CYLINDER BLOCK
EM-109
C
D
E
F
G
H
I
J
K
L
MA
EM
Revision: 2006 November2007 350Z
7. Drain engine coolant by removing water drain plugs (1, 4) from
cylinder block both sides as shown in the figure.
8.

Page 111 of 148

NISSAN 350Z 2007 Z33 Engine Mechanical Manual PDF CYLINDER BLOCK
EM-111
C
D
E
F
G
H
I
J
K
L
MA
EM
Revision: 2006 November2007 350Z
19. Remove lower cylinder block as follows:
Screw M8 bolt [Pitch: 1.25 mm (0.049 in), Length: approx. 50
mm (1.97 in)]

Page 112 of 148

NISSAN 350Z 2007 Z33 Engine Mechanical Manual PDF EM-112
CYLINDER BLOCK
Revision: 2006 November2007 350Z
2. Install each plug to cylinder block as shown in the figure.
Apply sealant to the thread of water drain plug (1).
Use Genuine RTV Silicone Sea

Page 113 of 148

NISSAN 350Z 2007 Z33 Engine Mechanical Manual PDF CYLINDER BLOCK
EM-113
C
D
E
F
G
H
I
J
K
L
MA
EM
Revision: 2006 November2007 350Z
c. Install main bearings paying attention to the direction.
Main bearing with oil hole (B) and groove (C) goes on cyli

Page 114 of 148

NISSAN 350Z 2007 Z33 Engine Mechanical Manual PDF EM-114
CYLINDER BLOCK
Revision: 2006 November2007 350Z
e. Turn lower cylinder block bolts (No.1 to 16) 90 degrees clock-
wise (angle tightening).
CAUTION:
Use the angle wrench [SST: KV10112100 (BT8653

Page 115 of 148

NISSAN 350Z 2007 Z33 Engine Mechanical Manual PDF CYLINDER BLOCK
EM-115
C
D
E
F
G
H
I
J
K
L
MA
EM
Revision: 2006 November2007 350Z
If there is stamped mark on ring, mount it with marked side
up.
Mount second ring with cut out side down.
Position e

Page 116 of 148

NISSAN 350Z 2007 Z33 Engine Mechanical Manual PDF EM-116
CYLINDER BLOCK
Revision: 2006 November2007 350Z
13. Install connecting rod bearing cap.
Match the stamped cylinder number marks on connecting rod
with those on connecting rod bearing cap to in

Page 117 of 148

NISSAN 350Z 2007 Z33 Engine Mechanical Manual PDF CYLINDER BLOCK
EM-117
C
D
E
F
G
H
I
J
K
L
MA
EM
Revision: 2006 November2007 350Z
Press-fit pilot bushing as the dimension in the figure. (M/T
models)
Press-fit pilot converter with its chamfer facin