key NISSAN 350Z 2007 Z33 Glasses, Windows System And Mirrors Workshop Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2007, Model line: 350Z, Model: NISSAN 350Z 2007 Z33Pages: 82, PDF Size: 2.92 MB
Page 1 of 82
GW-1
GLASSES, WINDOW SYSTEM & MIRRORS
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION GW
A
B
GW
Revision: 2006 November2007 350Z
GLASSES, WINDOW SYSTEM & MIRRORS
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for Battery Service ................................ 3
Precautions for Procedures without Cowl Top Cover ..... 3
Handling for Adhesive and Primer ........................... 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
Commercial Service Tools ........................................ 4
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 5
Work Flow ................................................................ 5
CUSTOMER INTERVIEW ..................................... 5
DUPLICATE THE NOISE AND TEST DRIVE ....... 6
CHECK RELATED SERVICE BULLETINS ........... 6
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ...................................................... 6
REPAIR THE CAUSE ........................................... 6
CONFIRM THE REPAIR ....................................... 7
Generic Squeak and Rattle Troubleshooting ........... 7
INSTRUMENT PANEL .......................................... 7
CENTER CONSOLE ............................................. 7
DOORS ................................................................. 7
TRUNK .................................................................. 8
SUNROOF/HEADLINING ..................................... 8
SEATS ................................................................... 8
UNDERHOOD ....................................................... 8
Diagnostic Worksheet .............................................. 9
WINDSHIELD GLASS ...............................................11
Removal and Installation ......................................... 11
REMOVAL (COUPE) ............................................ 11
REMOVAL (ROADSTER) ................................... 12
INSTALLATION ................................................... 12
BACK DOOR WINDOW GLASS .............................. 14
Removal and Installation ........................................ 14
REMOVAL ........................................................... 14
INSTALLATION ................................................... 15SIDE WINDOW GLASS ............................................ 16
Removal and Installation ........................................ 16
REMOVAL ........................................................... 16
INSTALLATION ................................................... 17
POWER WINDOW SYSTEM .................................... 18
Component Parts and Harness Connector Location ... 18
System Description ................................................. 19
MANUAL OPERATION ........................................ 19
POWER WINDOW SERIAL LINK ....................... 20
AUTO OPERATION ............................................. 20
POWER WINDOW LOCK ................................... 20
RETAINED POWER OPERATION ...................... 20
ANTI-PINCH SYSTEM ........................................ 21
POWER WINDOW CONTROL BY THE KEY
CYLINDER SWITCH ........................................... 21
AUTOMATIC WINDOW ADJUSTING FUNC-
TION .................................................................... 21
Schematic ............................................................... 22
Wiring Diagram — WINDOW — ............................. 23
Terminal and Reference Value for BCM ................. 26
Terminal and Reference Value for Power Window
Main Switch ............................................................ 27
Terminal and Reference Value for Power Window
Sub-Switch ............................................................. 28
CONSULT-III Function (BCM) ................................ 29
WORK SUPPORT ............................................... 29
DATE MONITOR ................................................. 29
ACTIVE TEST ..................................................... 29
Work Flow ............................................................... 30
Trouble Diagnoses Symptom Chart ....................... 30
Check BCM Power Supply and Ground Circuit ...... 32
Check Drive Side Power Window Motor Circuit ..... 33
Check Passenger Side Power Window Motor Cir-
cuit .......................................................................... 33
Check Limit Switch Circuit (Driver Side) ................. 34
Check Limit Switch Circuit (Passenger Side) ......... 36
Check Encoder Circuit (Driver Side) ....................... 37
Check Encoder Circuit (Passenger Side) ............... 39
Check Door Switch ................................................. 42
Check Power Window Serial Link ........................... 44
Page 2 of 82
GW-2Revision: 2006 November2007 350Z Check Power Window Main Switch Power Supply
and Ground Circuit ................................................. 46
Check Power Window Sub-switch Power Supply
and Ground ............................................................. 47
Check Door Key Cylinder Switch ............................ 48
FRONT DOOR GLASS AND REGULATOR ............. 51
Removal and Installation ........................................ 51
DOOR GLASS ..................................................... 51
REGULATOR ASSEMBLY .................................. 52
Disassembly and Assembly .................................... 52
REGULATOR ASSEMBLY .................................. 52
Inspection after Installation ..................................... 52
SETTING OF LIMIT SWITCH .............................. 52
FITTING INSPECTION ........................................ 53
INSIDE MIRROR ....................................................... 54
Wiring Diagram –I/MIRR– ...................................... 54
Removal and Installation ........................................ 55
REMOVAL ........................................................... 55
INSTALLATION .................................................... 55
REAR WINDOW DEFOGGER .................................. 56
Component Parts and Harness Connector Location ... 56
System Description ................................................. 56
CAN Communication System Description .............. 58
CAN Communication Unit ....................................... 58
Schematic– DEF – / For Coupe .............................. 59
Wiring Diagram –DEF– / For Coupe ....................... 60
Schematic – DEF – / For Roadster ......................... 63
Wiring Diagram –DEF– / For Roadster ................... 64
Terminal and Reference Value for BCM ................. 67
Terminal and Reference Value for IPDM E/R. ........ 67
Terminal and Reference Value for Unified Meter and A/C Amp. ................................................................. 67
CONSULT-III Function (BCM) ................................. 68
DATA MONITOR .................................................. 68
ACTIVE TEST ...................................................... 68
CONSULT-III Function (IPDM E/R) ......................... 68
DATA MONITOR .................................................. 68
ACTIVE TEST ...................................................... 68
Work Flow ............................................................... 69
Trouble Diagnoses Symptom Chart ........................ 69
Check IPDM E/R Operation .................................... 70
Check Rear Window Defogger Switch Circuit ......... 70
Check Rear Window Defogger Power Supply Cir-
cuit .......................................................................... 71
Check Rear Window Defogger Circuit / For Coupe ... 73
Check Rear Window Defogger Circuit / For Road-
ster .......................................................................... 74
Check Door Mirror Defogger Power Supply Circuit ... 75
Check Driver Side Door Mirror Defogger Circuit ..... 76
Check Passenger Side Door Mirror Defogger Circuit
... 76
Check Filament ....................................................... 78
Filament Repair ....................................................... 79
REPAIR EQUIPMENT ......................................... 79
REPAIRING PROCEDURE ................................. 79
DOOR MIRROR ......................................................... 80
Wring Diagram –MIRROR– .................................... 80
Removal and Installation ......................................... 81
REMOVAL ............................................................ 81
INSTALLATION .................................................... 81
DISASSEMBLY .................................................... 81
ASSEMBLY .......................................................... 82
Page 20 of 82
GW-20
POWER WINDOW SYSTEM
Revision: 2006 November2007 350Z
to power window sub-switch terminal 9
Then, the motor raises the window until the switch is released.
WINDOW DOWN
When the power window sub-switch is pressed in the down position,
Power is supplied
through power window sub-switch terminal 9
to passenger side power window motor terminal 1.
Ground is supplied
through passenger side power window motor terminal 2.
to power window sub-switch terminal 8
Then, the motor lowers the window until the switch is released.
POWER WINDOW MAIN SWITCH OPERATION
Signal is sent
though power window main switch terminal 12.
to power window sub-switch terminal 16
The operation of passenger side power window with power window main switch is as same as the operation
with power window sub-switch.
POWER WINDOW SERIAL LINK
Power window main switch, power window sub-switch and BCM transmit and receive the signal by power win-
dow serial link.
The under mentioned signal is transmitted from BCM to power window main switch.
Driver side door switch signal
Keyless power window down signal
The under mentioned signal is transmitted from BCM to power window sub-switch.
Passenger side door switch signal
Keyless power window down signal
The under mentioned signal is transmitted from power window main switch to power window sub-switch.
Passenger side door window operation signal
Power window control by key cylinder switch signal
Retained power operation signal
Power window lock signal
AUTO OPERATION
The power window AUTO feature enables the driver to open or close the window without holding the window
switch in the down or up position.
POWER WINDOW LOCK
The power window lock is designed to lock operation of passenger side door window.
When the lock position, power window lock signal is sent by using power window serial link from power win-
dow main switch to power window sub-switch.
When power window sub-switch is receiving the lock signal, prohibits the operation of passenger side power
window by power window sub-switch.
RETAINED POWER OPERATION
When the ignition switch is turned to the OFF position from ON or START position.
Power is supplied for 45 seconds
through BCM terminal 53.
to power window main switch terminal 10
When power and ground are supplied, the BCM continues to be energized, and the power window can be
operated.
The retained power operation is canceled when the driver side door or the passenger side door is opened.
RAP signal period can be changed by CONSULT-III. Refer to GW-29, "
CONSULT-III Function (BCM)" .
Page 21 of 82
POWER WINDOW SYSTEM
GW-21
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2006 November2007 350Z
ANTI-PINCH SYSTEM
Power window main switch and power window sub-switch monitors the power window motor operation and the
power window position (full closed or other) for driver side and passenger side power window by the signals
from encoder and limit switch in power window motor (driver side and passenger side).
When power window main switch detects interruption during the following close operation,
automatic close operation when ignition switch is in the “ON” position
automatic close operation during retained power operation
manual close operation during retained power operation
Power window main switch or power window sub-switch controls each power window motor for open and the
power window will be lowered about 150 mm (5.91 in).
POWER WINDOW CONTROL BY THE KEY CYLINDER SWITCH
When ignition key switch is OFF, power window can be opened or closed by turning the door key cylinder
UNLOCK / LOCK position more then 1.5 second over condition.
Power window can be opened as the door key cylinder is kept fully turning to the UNLOCK position.
Power window can be closed as the door key cylinder is kept fully turning to the LOCK position.
The power window operation by the key cylinder switch stops when the following operations are performed.
While performing open / close the window with power window main switch.
When the ignition switch is turned ON while the power window control operation by the key cylinder
switch.
AUTOMATIC WINDOW ADJUSTING FUNCTION
When the driver's / passenger's door(s) is opened, the window of the opened door is lowered approx. 10 mm
(0.39in).
When the door is closed, the window is raised to fully-closed positions.
Automatic window adjusting function system (opening operation) does not operate when the following.
The window is 10 mm (0.39 in) or more open from fully-closed positions.
Automatic window adjusting function system (closing operation) does not operate when the following.
The automatic window adjusting function system (opening operation) operation.
The keyless power window operation.
The power window control by the key cylinder switch operation.
Page 27 of 82
POWER WINDOW SYSTEM
GW-27
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2006 November2007 350Z
Terminal and Reference Value for Power Window Main SwitchNIS0004Q
*: For RoadsterTe r -
minalWire
ColorItemSignal
input/outputConditionVoltage (V)
(Approx.)
1 W BAT power supply Input — Battery voltage
4* PPower window down request
signalInputWhen soft top open/close
function starts and window
down function is operating.0
Other than above 5
5 OR Encoder power supply Input — 10
6 B/R Key cylinder lock switch OutputKey position
(Neutral → Locked)5 → 0
7 SB Key cylinder unlock switch OutputKey position
(Neutral → Unlocked)5 → 0
8LDriver side
power window motor UP signalOutputWhen power window motor
UP operation.Battery voltage
9 Y Limit switch signal InputDriver side door window is
between fully-open and just
before fully-closed position
(ON).0
Driver side door window is
between just before fully-
closed position and fully-
closed position (OFF).5
10 BR Rap signal OutputIGN SW ON Battery voltage
Within 45 second after igni-
tion switch is turned to OFFBattery voltage
When driver side or passenger
side door is open in power
window timer is operates0
11 GDriver side
power window motor DOWN
signalOutputWhen power window motor
DOWN operation. Battery voltage
12 PU/W Power window serial linkInput/Out-
put—
13 GY Encoder pulse signalInput/Out-
putWhen power window motor
operates.
14 LGLimit switch and encoder
ground—— 0
15 B Ground — — 0
PIIA2344J
OCC3383D
Page 31 of 82
POWER WINDOW SYSTEM
GW-31
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2006 November2007 350Z
Automatic window adjusting function does not operate.1. Check door switchGW-42
2. Limit switch adjustingGW-52
3. Check limit switch circuit (driver side)GW-34
4. Check limit switch circuit (passenger side)GW-36
5. Check power window serial linkGW-44
6. Replace BCM.BCS-17
Does not operate by the key cylinder switch.1. Check door key cylinder switchGW-482. Replace the power window main switch.EI-33
Power window lock switch does not function.1. Check power window serial linkGW-442. Replace the power window main switch.EI-33
Auto operation does not operate but manual operate
normally (driver side)1. Check encoder circuit (driver side)GW-37
2. Replace power window main switchEI-33
Auto operation does not operate but manual operate
normally (passenger side)1. Check encoder circuit (passenger side)GW-39
2. Replace power window sub-switchEI-33
Symptom Diagnoses / service procedureReference
page
Page 44 of 82
GW-44
POWER WINDOW SYSTEM
Revision: 2006 November2007 350Z
Check Power Window Serial LinkNIS00053
1. CHECK POWER WINDOW SWITCH OUTPUT SIGNAL
With CONSULT-III
Check door lock and unlock switch (“LOCK SW DR/AS”, “UNLK SW DR/AS”) in DATA MONITOR mode with
CONSULT-III. Refer to BL-35, "
DATA MONITOR" .
Without CONSULT-III
1. Remove key from ignition switch, and the door of driver side and passenger side is closed.
2. Check signal between BCM connector and ground with oscilloscope when door lock and unlock switch
(driver side and passenger side) is turned “LOCK” or “UNLOCK”.
3. Make sure signals which are shown in the figure below can be detected during 10 second just after door
lock and unlock switch (driver side and passenger side) is turned “LOCK” or “UNLOCK”.
OK or NG
OK >> GO TO 2.
NG >> GO TO 3.
2. CHECK BCM OUTPUT SIGNAL
Check power window serial link (“POWER WINDOW DOWN”) in “ACTIVE TEST” mode with CONSULT-III.
Refer to BL-74, "
Active Test" .
When “ACTIVE TEST” is perform, is the window of driver side and passenger side lowered?
OK or NG
OK >> Further inspection is necessary. Refer to symptom chart.
NG >> Replace BCM.
Monitor item Condition
CDL LOCK SWLOCK: ON
UNLOCK: OFF
CDL UNLOCK SWLOCK: OFF
UNLOCK: ON
ConnectorTerminals (Wire color)
Signal
(Reference valve)
(+) (–)
M90 22 (Y) Ground
PIIA6290EPIIA1297E
Page 48 of 82
GW-48
POWER WINDOW SYSTEM
Revision: 2006 November2007 350Z
3. CHECK POWER WINDOW SUB-SWITCH POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM and power window sub-switch connector.
3. Check continuity between BCM connector M91 terminal 54 and
power window sub-switch connector D37 terminal 10.
4. Check continuity between BCM connector M91 terminal 54 and
ground.
OK or NG
OK >> Check the condition of the harness and the connector.
NG >> Repair or replace harness.
Check Door Key Cylinder Switch NIS00056
1. CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL
With CONSULT-III
Check door key cylinder switch (“KEY CYL LK-SW”, “KEY CYL UN-SW”) in “DATA MONITOR” mode with
CONSULT-III.
Without CONSULT-III
1. Turn ignition switch OFF.
2. Check voltage between power window main switch connector and ground.
OK or NG
OK >> Door key cylinder switch is OK.
NG >> GO TO 2.54 (W) – 10 (W) : Continuity should exist.
54 (W) – Ground : Continuity should not exist.
PIIA9470E
Monitor item Condition
KEY CYL LK- SWLock: ON
Neutral/Unlock: OFF
KEY CYL UN- SWUnlock: ON
Neutral/Lock: OFF
ConnectorTerminals (Wire color)
Key position Voltage (V)
(Approx.)
(+) (–)
D76 (B/R)
GroundNeutral/Unlock 5
Lock 0
7 (SB)Neutral/Lock 5
Unlock 0
PIIA3352E
Page 49 of 82
POWER WINDOW SYSTEM
GW-49
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2006 November2007 350Z
2. CHECK DOOR KEY CYLINDER SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect power window main switch and door key cylinder switch connector.
3. Check continuity between power window main switch connector
D7 terminal 6, 7 and door key cylinder switch connector D12 ter-
minals 1, 3.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK DOOR KEY CYLINDER SWITCH GROUND
Check continuity between door key cylinder switch connector D12
terminal 2 and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness.
4. CHECK DOOR KEY CYLINDER SWITCH
Check continuity between door key cylinder switch connector D12 terminals 1, 3 and 2.
OK or NG
OK >> GO TO 5.
NG >> Replace door key cylinder switch.6 (B/R) – 3 (B/R) : Continuity should exist.
7 (SB) – 1 (SB) : Continuity should exist.
PIIA3353E
2 (B) – Ground : Continuity should exist.
PIIA3354E
Connector Terminal Key position Continuity
D121
2Neutral/Lock No
Unlock Yes
3Neutral/Unlock No
Lock Yes
PIIA3355E