battery NISSAN 350Z 2007 Z33 Road Wheels And Tires Workshop Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2007, Model line: 350Z, Model: NISSAN 350Z 2007 Z33Pages: 40, PDF Size: 1.11 MB
Page 1 of 40
WT-1
ROAD WHEELS & TIRES
E SUSPENSION
CONTENTS
C
D
F
G
H
I
J
K
L
M
SECTION WT
A
B
WT
Revision: 2006 November2007 350Z
ROAD WHEELS & TIRES
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for Battery Service ................................ 3
Service Notice or Precautions .................................. 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
Commercial Service Tools ........................................ 4
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING ................................................ 5
NVH Troubleshooting Chart ..................................... 5
ROAD WHEEL ............................................................ 6
Inspection ................................................................. 6
ALUMINUM WHEEL ............................................. 6
STEEL WHEEL ..................................................... 6
ROAD WHEEL TIRE ASSEMBLY .............................. 7
Balancing Wheels (Bonding Weight Type) ............... 7
REMOVAL ............................................................. 7
WHEEL BALANCE ADJUSTMENT ...................... 7
Tire Rotation ............................................................. 8
DESCRIPTION ...................................................... 8
TIRE PRESSURE MONITORING SYSTEM ............. 10
System Components .............................................. 10
System Description ................................................ 10
TRANSMITTER ................................................... 10
REMOTE KEYLESS ENTRY RECEIVER ........... 10
BCM (BODY CONTROL MODULE) ..................... 11
LOW TIRE PRESSURE WARNING LAMP .......... 11
Can Communication ............................................... 12
SYSTEM DESCRIPTION .................................... 12
TROUBLE DIAGNOSIS ............................................ 13
How to Perform Trouble Diagnosis ........................ 13
BASIC CONCEPT ............................................... 13
INTRODUCTION ................................................. 13
WORK FLOW ...................................................... 14
Schematic .............................................................. 15
Wiring Diagram — T/WARN — .............................. 16
Trouble Diagnosis Chart for Symptoms ................. 19
Control Unit Input/Output Signal Standard ............. 20ID Registration Procedure ...................................... 21
ID REGISTRATION WITH ACTIVATION TOOL ... 21
ID REGISTRATION WITHOUT ACTIVATION
TOOL ................................................................... 21
Transmitter Wake Up Operation ............................. 22
WITH ACTIVATION TOOL .................................. 22
CONSULT-III Function (BCM) ................................ 22
CONSULT-III MAIN FUNCTION .......................... 22
WORK SUPPORT MODE ................................... 22
SELF-DIAG RESULTS MODE ............................ 23
DATA MONITOR MODE ...................................... 24
ACTIVE TEST MODE ......................................... 25
Diagnosis Procedure with Warning Lamp Function
(Without CONSULT-III) ........................................... 26
DESCRIPTION .................................................... 26
FUNCTION .......................................................... 26
MALFUNCTION CODE CHART .......................... 26
LOW TIRE PRESSURE WARNING LAMP
SYMPTOM CHART ............................................. 27
Preliminary Check .................................................. 29
BASIC INSPECTION ........................................... 29
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC
ITEMS ........................................................................ 30
Transmitter or Control Unit (BCM) .......................... 30
MALFUNCTION CODE NO. 21, 22, 23 OR 24 ... 30
Transmitter - 1 ........................................................ 30
MALFUNCTION CODE NO. 31, 32, 33, 34, 41,
42, 43, 44, 45, 46, 47 OR 48 ............................... 30
Transmitter - 2 ........................................................ 31
MALFUNCTION CODE NO. 35, 36, 37 OR 38 ... 31
Vehicle Speed Signal .............................................. 32
MALFUNCTION CODE NO. 52 ........................... 32
TROUBLE DIAGNOSIS FOR SYMPTOMS .............. 33
Warning Lamp Does Not Come On When Ignition
Switch Is Turned On ............................................... 33
DIAGNOSTIC PROCEDURE .............................. 33
Warning Lamp Stays On When Ignition Switch Is
Turned On .............................................................. 33
DIAGNOSTIC PROCEDURE .............................. 33
Warning Lamp Blinks When Ignition Switch Is
Page 3 of 40
PRECAUTIONS
WT-3
C
D
F
G
H
I
J
K
L
MA
B
WT
Revision: 2006 November2007 350Z
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NES000LO
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Battery ServiceNES000LP
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Service Notice or PrecautionsNES000LQ
Low tire pressure warning lamp flashes 1min., then turns ON when occurring any malfunction except low
tire pressure.
Delete the memory with CONSULT-III, or register the ID to turn low tire pressure warning lamp OFF. Refer
to WT-21, "
ID Registration Procedure" .
ID registration is required when replacing or rotating wheels. replacing transmitter or BCM. Refer to WT-
21, "ID Registration Procedure" .
Replace grommet seal, valve core and cap of the transmitter in TPMS every tire replacement by reaching
wear limit of tire.
Page 20 of 40
WT-20
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
Control Unit Input/Output Signal StandardNES0001F
Standards using a circuit tester and oscilloscope
Te r m i n a l
(Wire color)Item ConditionVoltage (V)
Approx. value
15 (W)Tire pressure warning check con-
nectorAlways 5V
18 (B)Remote keyless entry receiver
(Ground)—0V
19 (Y)Remote keyless entry receiver
(Power supply)Stand-by
Press any of the keyfob switches
20 (L)Remote keyless entry receiver
(Signal)Stand-by
Press any of the keyfob switches
38 (W/L) Ignition switch Ignition switch ON or START Battery voltage (12V)
39 (L) Data line (CAN H) — —
40 (P) Data line (CAN L) — —
42 (GY) Battery power supply (Fuse) Always Battery voltage (12V)
45 (G/W) Turn signal (left)
Ignition switch ON
Combination switch is turn left ON
OCC3879D
OCC3882D
OCC3881D
OCC3880D
SKIA3009J
Page 21 of 40
TROUBLE DIAGNOSIS
WT-21
C
D
F
G
H
I
J
K
L
MA
B
WT
Revision: 2006 November2007 350Z
ID Registration ProcedureNES0001G
ID REGISTRATION WITH ACTIVATION TOOL
This procedure must be done after replacing or rotating wheels, replacing transmitter or BCM.
1. Select “AIR PRESSURE MONITOR” on “SELECT WORK ITEM”.
2. Touch “WORK SUPPORT” on “SELECT DIAG MODE” screen, and select “ID REGIST”.
3. With the activation tool (J-45295) pushed against the front-left
transmitter position of the tire air valve, press the button then
keep 5 seconds.
4. Register the IDs in order from FR LH, FR RH, RR RH to RR LH.
When ID registration of each wheel has been completed, a
buzzer sounds and turn signal lamp (LH/ RH) blinks.
5. After completing all ID registrations, press “END” to complete the procedure.
NOTE:
Be sure to register the IDs in order from FR LH, FR RH, RR RH, to RR LH, or the self-diagnostic results dis-
play will not function properly.
ID REGISTRATION WITHOUT ACTIVATION TOOL
This procedure must be done after replacing or rotating wheels, replacing transmitter or BCM.
1. Select “AIR PRESSURE MONITOR” on “SELECT WORK ITEM”.
2. Touch “WORK SUPPORT” on “SELECT DIAG MODE” screen, and select “ID REGIST”.
3. Adjust the tire pressure to the values shown in the table below for ID registration, and drive the vehicle at
40 km/h (25 MPH) or more for a few minutes.
4. After completing all ID registrations, press “END” to complete the procedure.
46 (PU/W) Turn signal (right)
Ignition switch ON
Combination switch is turn right
ON
52 (B) GND — 0V
55 (R) Battery power supply (F/L) Always Battery voltage (12V)Terminal
(Wire color)Item ConditionVoltage (V)
Approx. value
SKIA3009J
Activation tire position Buzzer Turn signal lamp CONSULT-III
1 Front LH Once
2 times flashing“Red”
↓
“Green” 2 Front RH 2 times
3 Rear RH 3 times
4 Rear LH 4 times
SEIA0460E
Tire position
Tire pressure kPa (kg/cm2 , psi)
Front − Left 240 (2.4, 34)
Front − Right 220 (2.2, 31)
Rear − Right 200 (2.0, 29)
Rear − Left 180 (1.8, 26)
Activation tire position CONSULT-III
Front LH
“Red”
↓
“Green” Front RH
Rear RH
Rear LH
Page 23 of 40
TROUBLE DIAGNOSIS
WT-23
C
D
F
G
H
I
J
K
L
MA
B
WT
Revision: 2006 November2007 350Z
SELF-DIAG RESULTS MODE
Display Item List
NOTE:
Before performing the self-diagnosis, be sure to register the ID, or else the actual malfunction location may be different from that dis-
played on CONSULT-III.DTC Diagnostic item Diagnostic item is detected when ··· Check items
C1704 FLAT_TIRE_FL
Front-left tire pressure drops to 190 kPa (1.90 kg/cm
2 , 28 psi) or less.
— C1705 FLAT_TIRE_FR
Front-right tire pressure drops to 190 kPa (1.90 kg/cm
2 , 28 psi) or less.
C1706 FLAT_TIRE_RR
Rear-right tire pressure drops to 190 kPa (1.90 kg/cm
2 , 28 psi) or less.
C1707 FLAT_TIRE_RL
Rear-left tire pressure drops to 190 kPa (1.90 kg/cm
2 , 28 psi) or less.
C1708 [NO_DATA]_FL Data from front-left transmitter cannot be received.
WT-30
C1709 [NO_DATA]_FR Data from front-right transmitter cannot be received.
C1710 [NO_DATA]_RR Data from rear-right transmitter cannot be received.
C1711 [NO_DATA]_RL Data from rear-left transmitter cannot be received.
C1712 [CHECKSUM_ERR]_FL Checksum data from front-left transmitter is malfunctioning.
WT-30
C1713 [CHECKSUM_ERR]_FR Checksum data from front-right transmitter is malfunctioning.
C1714 [CHECKSUM_ERR]_RR Checksum data from rear-right transmitter is malfunctioning.
C1715 [CHECKSUM_ERR]_RL Checksum data from rear-left transmitter is malfunctioning.
C1716 [PRESSDATA_ERR]_FL Air pressure data from front-left transmitter is malfunctioning.
WT-31
C1717 [PRESSDATA_ERR]_FR Air pressure data from front-right transmitter is malfunctioning.
C1718 [PRESSDATA_ERR]_RR Air pressure data from rear-right transmitter is malfunctioning.
C1719 [PRESSDATA_ERR]_RL Air pressure data from rear-left transmitter is malfunctioning.
C1720 [CODE_ERROR]_FL Function code data from front-left transmitter is malfunctioning.
WT-30
C1721 [CODE_ERROR]_FR Function code data from front-right transmitter is malfunctioning.
C1722 [CODE_ERROR]_RR Function code data from rear-right transmitter is malfunctioning.
C1723 [CODE_ERROR]_RL Function code data from rear-left transmitter is malfunctioning.
C1724 [BATT_VOLT_LOW]_FL Battery voltage of front-left transmitter drops.
WT-30
C1725 [BATT_VOLT_LOW]_FR Battery voltage of front-right transmitter drops.
C1726 [BATT_VOLT_LOW]_RR Battery voltage of rear-right transmitter drops.
C1727 [BATT_VOLT_LOW]_RL Battery voltage of rear-left transmitter drops.
C1729 VHCL_SPEED_SIG_ERR Vehicle speed signal is error.WT-32
Page 26 of 40
WT-26
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
Diagnosis Procedure with Warning Lamp Function (Without CONSULT-III)NES000A4
DESCRIPTION
During driving, the low tire pressure warning system receives the signal transmitted from the transmitter
installed in each wheel. The control unit (BCM) of this system has pressure judgement and trouble diagnosis
functions.
FUNCTION
When the low tire pressure warning system detects low inflation pressure or another unusual symptom, the
warning lamps in the combination meter comes on. To start the self-diagnostic results mode, ground terminal
of the tire pressure warning check connector. The malfunction location is indicated by the warning lamp flash-
ing. Refer to PG-41, "
HARNESS" .
MALFUNCTION CODE CHART
Code (warning lamp blinks) Diagnosis item Reference
15
Front-left tire pressure drops to 190 kPa (1.90 kg/cm
2 , 28 psi) or less.
— 16
Front-right tire pressure drops to 190 kPa (1.90 kg/cm
2 , 28 psi) or less.
17
Rear-right tire pressure drops to 190 kPa (1.90 kg/cm
2 , 28 psi) or less.
18
Rear-left tire pressure drops to 190 kPa (1.90 kg/cm
2 , 28 psi) or less.
21 Transmitter no data (front - left)
WT-30
22 Transmitter no data (front - right)
23 Transmitter no data (rear - right)
24 Transmitter no data (rear - left)
31 Transmitter checksum error (front - left)
WT-30
32 Transmitter checksum error (front - right)
33 Transmitter checksum error (rear - right)
34 Transmitter checksum error (rear - left)
35 Transmitter pressure data error (front - left)
WT-31
36 Transmitter pressure data error (front - right)
37 Transmitter pressure data error (rear - right)
38 Transmitter pressure data error (rear - left)
41 Transmitter function code error (front - left)
WT-30
42 Transmitter function code error (front - right)
43 Transmitter function code error (rear - right)
44 Transmitter function code error (rear - left)
45 Transmitter battery voltage low (front - left)
WT-30
46 Transmitter battery voltage low (front - right)
47 Transmitter battery voltage low (rear - right)
48 Transmitter battery voltage low (rear - left)
52 Vehicle speed signalWT-32
Page 28 of 40
WT-28
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
NOTE:
If more than one wheel transmitter is NOT activated, the warning light blinking patterns for those wheels will combine. (Example: one
blink/OFF/three blinks = Rear LH and Rear RH transmitters are not activated.)Low tire pres-
sure warning
lampWarning light blinks 4
times.Rear LH wheel trans-
mitter is not acti-
vated.Activate rear LH wheel
transmitter. Refer to WT-22,
"Transmitter Wake Up Oper-
ation" .
Warning light comes
on and does not turn
off.Tire pressure is low.Check tire pressure with
CONSULT-III. Refer to WT-
24, "DATA MONITOR
MODE" .
The fuse for combi-
nation meter from
battery is pulled out.Check the fuse for combina-
tion meter from battery.
Install or replace (if needed).
BCM connector
pulled out.Check BCM connector. Re-
connect if needed.
Low tire pressure or
tire pressure moni-
toring system mal-
function.
Perform CONSULT-III
Self- Diagnosis. Refer to
WT-23, "
SELF-DIAG
RESULTS MODE" .
–Perform ID Registration if
needed. Refer to WT-21,
"ID Registration Proce-
dure" .
Turn signal
lampTurn signal lamp
does not flash 2
times or horn does
not sound after trans-
mitter activation.—1. Tool J-45295 (spe-
cial service tool)
battery low.
2. Ignition OFF dur-
ing activation.
3. Tool J-45295 (spe-
cial service tool)
not positioned cor-
rectly.
4. Transmitters
already activated.1. Install new battery.
2. Make sure ignition is ON
during activation.
3. Position tool correctly dur-
ing activation.
4. None Diagnosis
ItemSymptom
(Ignition switch ON)Low tire pressure warning lamp Cause Action
SEIA0597E
SEIA0598E
Page 29 of 40
TROUBLE DIAGNOSIS
WT-29
C
D
F
G
H
I
J
K
L
MA
B
WT
Revision: 2006 November2007 350Z
Preliminary CheckNES0001K
BASIC INSPECTION
1. CHECK ALL TIRE PRESSURES
Check all tire pressures. Refer to WT-39, "SERVICE DATA AND SPECIFICATIONS (SDS)" .
OK or NG
OK >> GO TO 2.
NG >> Adjust tire pressure to specified value.
2. CHECK LOW TIRE PRESSURE WARNING LAMP ACTIVATION
Check low tire pressure warning lamp activation.
Dose low tire pressure warning lamp activate for 1 second when ignition switch is turned
“ON”?
YES >> GO TO 3.
NO >> Check fuse and combination meter.
3. CHECK CONNECTOR
1. Disconnect BCM harness connectors M90 and M91.
2. Check terminals for damage or loose connection.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace damaged parts.
4. CHECK ACTIVATION TOOL
Check activation tool battery.
OK or NG
OK >> Perform self-diagnosis.
NG >> Replace activation tool battery.
Page 34 of 40
WT-34
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2006 November2007 350Z
3. CHECK CONNECTOR
1. Turn ignition switch OFF.
2. Disconnect BCM harness connectors M90 and M91.
3. Check terminals for damage or loose connections.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace damaged parts.
4. CHECK POWER SUPPLY CIRCUIT (BATTERY)
1. Turn ignition switch OFF.
2. Disconnect BCM harness connector.
3. Check voltage between BCM harness connector M91 terminals 42, 55 and ground.
OK or NG
OK >> GO TO 5.
NG >> Check BCM power supply circuit for open or short.
5. CHECK POWER SUPPLY CIRCUIT (IGN)
1. Turn ignition switch OFF.
2. Disconnect BCM harness connector.
3. Turn ignition switch ON.
4. Check voltage between BCM harness connector M90 terminal
38 and ground.
OK or NG
OK >> GO TO 6.
NG >> Check BCM power supply circuit for open or short.
Connector Terminal Voltage (Approx.)
M9142 - Ground
Battery voltage
55 - Ground
SEIA0435E
Connector Terminal Voltage (Approx.)
M90 38 - Ground Battery voltage
SEIA0436E