diagram NISSAN 350Z 2007 Z33 Road Wheels And Tires Workshop Manual

WT-1
ROAD WHEELS & TIRES
E SUSPENSION
CONTENTS
C
D
F
G
H
I
J
K
L
M
SECTION WT
A
B
WT
Revision: 2006 November2007 350Z
ROAD WHEELS & TIRES
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for Battery Service ................................ 3
Service Notice or Precautions .................................. 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
Commercial Service Tools ........................................ 4
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING ................................................ 5
NVH Troubleshooting Chart ..................................... 5
ROAD WHEEL ............................................................ 6
Inspection ................................................................. 6
ALUMINUM WHEEL ............................................. 6
STEEL WHEEL ..................................................... 6
ROAD WHEEL TIRE ASSEMBLY .............................. 7
Balancing Wheels (Bonding Weight Type) ............... 7
REMOVAL ............................................................. 7
WHEEL BALANCE ADJUSTMENT ...................... 7
Tire Rotation ............................................................. 8
DESCRIPTION ...................................................... 8
TIRE PRESSURE MONITORING SYSTEM ............. 10
System Components .............................................. 10
System Description ................................................ 10
TRANSMITTER ................................................... 10
REMOTE KEYLESS ENTRY RECEIVER ........... 10
BCM (BODY CONTROL MODULE) ..................... 11
LOW TIRE PRESSURE WARNING LAMP .......... 11
Can Communication ............................................... 12
SYSTEM DESCRIPTION .................................... 12
TROUBLE DIAGNOSIS ............................................ 13
How to Perform Trouble Diagnosis ........................ 13
BASIC CONCEPT ............................................... 13
INTRODUCTION ................................................. 13
WORK FLOW ...................................................... 14
Schematic .............................................................. 15
Wiring Diagram — T/WARN — .............................. 16
Trouble Diagnosis Chart for Symptoms ................. 19
Control Unit Input/Output Signal Standard ............. 20ID Registration Procedure ...................................... 21
ID REGISTRATION WITH ACTIVATION TOOL ... 21
ID REGISTRATION WITHOUT ACTIVATION
TOOL ................................................................... 21
Transmitter Wake Up Operation ............................. 22
WITH ACTIVATION TOOL .................................. 22
CONSULT-III Function (BCM) ................................ 22
CONSULT-III MAIN FUNCTION .......................... 22
WORK SUPPORT MODE ................................... 22
SELF-DIAG RESULTS MODE ............................ 23
DATA MONITOR MODE ...................................... 24
ACTIVE TEST MODE ......................................... 25
Diagnosis Procedure with Warning Lamp Function
(Without CONSULT-III) ........................................... 26
DESCRIPTION .................................................... 26
FUNCTION .......................................................... 26
MALFUNCTION CODE CHART .......................... 26
LOW TIRE PRESSURE WARNING LAMP
SYMPTOM CHART ............................................. 27
Preliminary Check .................................................. 29
BASIC INSPECTION ........................................... 29
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC
ITEMS ........................................................................ 30
Transmitter or Control Unit (BCM) .......................... 30
MALFUNCTION CODE NO. 21, 22, 23 OR 24 ... 30
Transmitter - 1 ........................................................ 30
MALFUNCTION CODE NO. 31, 32, 33, 34, 41,
42, 43, 44, 45, 46, 47 OR 48 ............................... 30
Transmitter - 2 ........................................................ 31
MALFUNCTION CODE NO. 35, 36, 37 OR 38 ... 31
Vehicle Speed Signal .............................................. 32
MALFUNCTION CODE NO. 52 ........................... 32
TROUBLE DIAGNOSIS FOR SYMPTOMS .............. 33
Warning Lamp Does Not Come On When Ignition
Switch Is Turned On ............................................... 33
DIAGNOSTIC PROCEDURE .............................. 33
Warning Lamp Stays On When Ignition Switch Is
Turned On .............................................................. 33
DIAGNOSTIC PROCEDURE .............................. 33
Warning Lamp Blinks When Ignition Switch Is

WT-16
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
Wiring Diagram — T/WARN —NES0001E
TEWT0056E

WT-22
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
5. Inflate all tires to proper pressure. Refer to WT-39, "SERVICE DATA AND SPECIFICATIONS (SDS)" .
Transmitter Wake Up OperationNES0001H
WITH ACTIVATION TOOL
1. With the activation tool (J-45295) pushed against the front-left
transmitter, press the button for 5 seconds.

When ignition switch ON, as the low tire pressure warning
lamp blinks per the follow diagram, the respective transmitter
then must be woken up.
2. Register the ID of wheel that warning lamp flashes. When wake up of registered wheel has been com-
pleted, turn signal lamp flashes two times.
3. After completing wake up of all transmitters, make sure low tire pressure warning lamp goes out.
CONSULT-III Function (BCM)NES000DL
CONSULT-III MAIN FUNCTION
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
WORK SUPPORT MODE
ID Read
The registered ID number is displayed.
ID Regist
Refer to WT-21, "ID Registration Procedure" .
SEIA0460E
SEIA0378E
BCM diagnosis part Mode Function
Air pressure monitorWork supportThis mode enables a technician to adjust some devices faster and more accurately
by following the indications on CONSULT-III.
Self-diagnostic results Self-diagnostic results can be read and erased quickly.
Data monitor Input/Output data in the control unit can be read.
Active testDiagnostic Test Mode in with CONSULT-III drives some actuators apart from the
control unit (BCM) and also shifts some parameters in a specified range.