NISSAN 350Z 2007 Z33 Seat Manual PDF
Manufacturer: NISSAN, Model Year: 2007, Model line: 350Z, Model: NISSAN 350Z 2007 Z33Pages: 80, PDF Size: 2.89 MB
Page 71 of 80
SEAT
SE-71
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2006 November2007 350Z
1. Headrest 2. Headrest holder (locked) 3. Headrest holder (free)
4. Seatback pad 5. Seat cushion pad 6. Seatback trim
7. Seat cushion trim 8. Side air bag module 9. Side air bag module bracket
10. Inner cloth stay 11. Side air bag module harness 12. Seatback frame
13. Seat cushion frame 14. Reclining device rod 15.Seat thigh support adjuster assem-
bly
16. Inner cover outer device 17. Reclining device outer 18. Seat cushion outer finisher
19. Lifter dial 20. Sliding outer assembly 21. Flexible wire
22. Sliding inner assembly 23. Power seat harness 24. Seat belt buckle
25. Seat belt buckle bracket 26. Inner cover inner device 27. Reclining device inner
28. Seat cushion inner finisher 29. Power seat switch
Page 72 of 80
SE-72
SEAT
Revision: 2006 November2007 350Z
NET SEAT (ROADSTER)
1. Seatback frame and pad upper 2. Inner cloth stay 3. Side air bag module
4. Seatback trim upper 5. Seatback trim lower 6. Seatback pad lower
PIIB9181E
Page 73 of 80
SEAT
SE-73
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2006 November2007 350Z
REMOVAL
When removing or installing the seat trim, carefully handle it to keep dirt out and avoid damage.
CAUTION:
Before removing the seat, turn the ignition switch off, disconnect both battery cables and wait at
least 3 minutes.
When checking the power seat circuit for continuity using a circuit tester, do not confuse its con-
nector with the side air bag module connector. Such an error may cause the air bag to deploy.
Do not drop, tilt, or bump the side air bag module installing in the seat. Always handle it with care.
1. Remove the front leg cover and rear leg cover (LH/RH).
2. Slide the seat until the body mounting bolts are visible and a tool can be inserted.
3. Remove mounting bolts from vehicle.
4. Disconnect both battery cables.
5. Disconnect harness connector from under seat cushion.
6. Remove fastening clips under seat cushion, and remove seats
from vehicle.
INSTALLATION
Install in the reverse order of removal.
7. Seatback garnish 8. Seat cushion trim 9. Seat cushion pad
10. Seatback frame 11. Seat cushion inner finisher 12. Reclining inner device
13. Power seat switch 14. Inner cover inner device 15. Seat cushion frame
16. Reclining device rod 17. Reclining outer device 18. Inner cover outer device
19. Side air bag module harness 20. Seat cushion outer finisher 21. Lifter dial
22. Seat belt buckle 23. Power seat harness 24. Sliding inner assembly
25. Flexible wire 26. Seat thigh support adjuster assem-
bly27. Sliding outer assembly
PIIA2517E
Page 74 of 80
SE-74
SEAT
Revision: 2006 November2007 350Z
Disassembly and AssemblyNIS000AM
SEATBACK TRIM AND PAD (MANUAL SEAT AND POWER SEAT)
Disassembly
1. Open fastener on back of seatback, and remove retainer from
seatback trim.
2. Remove the stay securing the inner cloth.
3. Squeeze and pull up headrest holder tabs to remove from seat-
back frame.
NOTE:
Before installing the headrest holder, check its orientation (front/
rear and right/left).
4. Remove the seat heater harness connector. After removing the seatback trim and pad, remove the hog
ring to separate the trim and pad.
NOTE:
Seatback heater unit is stitched into seatback trim. It cannot be separated (for heated seat models only).
Assembly
Assemble in the reverse order of disassembly.
REMOVAL OF SEATBACK ASSEMBLY
1. After completing the steps 1 of “SEATBACK TRIM AND PAD”, remove the harness connectors for the
reclining motor (driver seat only).
2. Pull out the harness connector for the side air bag from the seat cushion.
3. Remove the reclining device mounting bolts on the seatback frame, and remove the seatback assembly.
NOTE:
When assembling the seatback frame, make sure that the reclining device are locked on both sides, and
be sure to temporarily tighten the bolts, then tighten them finally.
INSTALLATION OF SEATBACK ASSEMBLY
Install in the reverse order of removal.
PIIA2518E
PIIA2519E
PIIA1158E
Page 75 of 80
SEAT
SE-75
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2006 November2007 350Z
SEATBACK TRIM AND PAD (NET SEAT FOR ROADSTER)
Disassembly
1. Remove the seatback garnish.
2. Open fastener on seatback lower.
3. Remove the retainer.
4. Disconnect side air bag connector.
5. Remove the seatback upper mounting bolts.
PIIA7826E
PIIA7827E
PIIA7828E
PIIA7829E
Page 76 of 80
SE-76
SEAT
Revision: 2006 November2007 350Z
6. Open fastener on seatback upper.
7. Remove the stay securing the inner cloth.
8. Separate the seatback frame and pad upper and seatback trim upper.
9. Remove the retainer.
10. After removing the seatback trim and pad, remove the hog rings to separate the trim and pad.
Assembly
Assemble in the reverse order of disassembly.
PIIA7830E
PIIA7831E
PIIA7832E
Page 77 of 80
SEAT
SE-77
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2006 November2007 350Z
SEAT CUSHION TRIM AND PAD (POWER SEAT AND NET SEAT)
CAUTION:
Do not disassemble front passenger seat cushion assembly.
Always replace as an assembly.
For front passenger seat service parts, refer to the service part catalogue.
Disassembly
1. Hang snap ring on wire, and pull it up to remove. Remove Lifter
dial.
2. Unfasten the screw and metal clip and remove the seat cushion
outer finisher.
3. Unfasten screws and remove the power seat switch assembly.
Insert a screwdriver in lower side of power seat switch and
remove it (passenger seat for coupe).
PIIA8726E
PIIA8727E
PIIA2522E
PIIA2930E
Page 78 of 80
SE-78
SEAT
Revision: 2006 November2007 350Z
4. Remove bolts on the under side of seat cushion.
5. Remove hog rings from under seat cushion frame.
6. Disconnect harness connector from seat cushion heater unit.
7. After removing the seat cushion trim and pad, remove the hog rings to separate the trim and pad.
NOTE:
Seat cushion heater unit is stitched into seat cushion trim. It cannot be separated.
Assembly
Assemble in the reverse order of disassembly.
SEAT CUSHION TRIM AND PAD (MANUAL SEAT FOR COUPE)
CAUTION:
Do not disassemble front passenger seat cushion assembly.
Always replace as an assembly.
For front passenger seat service parts, refer to the service part catalogue.
Disassembly
1. Pull up tabs of reclining lever from inside. Slide knob forward to
remove.
PIIA7833E
PIIA7834E
PIIA1161E
Page 79 of 80
SEAT
SE-79
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2006 November2007 350Z
2. Hang snap ring on wire, and pull it up to remove. Remove thigh
support adjuster dial.
3. Unfasten the screw and metal clip and remove the seat cushion
outer finisher.
4. Remove bolts on the under side of seat cushion.
5. Remove hog rings from under seat cushion frame.
6. After removing the seat cushion trim and pad, remove the hog rings to separate the trim and pad.
Assembly
Assemble in the reverse order of disassembly.
PASSENGER SIDE SEATBACK FORWARD RECLINING (COUPE)
1. Remove passenger side seatback trim and pad. Refer to SE-74, "SEATBACK TRIM AND PAD (MANUAL
SEAT AND POWER SEAT)" .
2. Remove screw and fixing clip, then disconnect cable wire.
PASSENGER SIDE SEATBACK FORWARD RECLINING (ROADSTER)
1. Remove the seatback tilt switch.
2. Disconnect seatback tilt switch harness connector.
PIIA2520E
PIIA2521E
PIIA2523E
PIIA8543E
Page 80 of 80
SE-80
SEAT
Revision: 2006 November2007 350Z
3. Remove passenger side seatback trim and pad. Refer to SE-74, "SEATBACK TRIM AND PAD (MANUAL
SEAT AND POWER SEAT)" .