alternator NISSAN ALMERA N15 1995 Owner's Manual

Unit:mm(in)
10
(0.39)

n'

Engine front
1+ .,..I

3 (0.12) ~LiqUid
gasket

SEM366D TIMING
CHAIN
Installation (Cont'd)

26. Install intakemanifold supports.
27. Remove allold liquid gasket frommating surfaces ofrocker
cover gasket andcylinder head.
28. Apply acontinuous beadofliquid gasket tomating surfaces
of rocker covergasket andcylinder head.

• Use Genuine LiquidGasket orequivalent.
•

3
1
mm (0.12
In)r~
liquidgasket

tJ$j

SEM367D

@

8l"-L~~[c,.l~
Q

[0 O@O 0

CD

Oil separator
Tighten innumerical order.

SEM585D
29.
Install rocker coverandoilseparator.

(1) Tighten nuts
C!J-
@l -
@ -@ -
cID
inthat order to4N'm
(0.4 kg-m, 35in-Ib).
(2) Tighten nuts
d)
through @innumerical orderto8to 10
N'm (0.8to1.0 kg-m, 69to87 in-Ib).

30. Refit spark plugsandleads.
31. Install vacuum hoses,fuelhoses, wires,harness, connec-
tors andsoon.
32. Install power steering oilpump andalternator.
33. Install waterpumppulley anddrive belts.
34. Refit airduct tointake manifold.
35. Install radiator.
36. Refit hoses andrefill withcoolant. (RefertoMA section.)
37. Install engine sidecover andfront RHwheel.
38. Install engine undercovers.

EM-81

SEM092DENGINE
REMOVAL
WARNING:
• Situate vehicle onaflat and solid surface.
• Place chocks atfront andback ofrear wheels.
• Donot remove engineuntilexhaust systemhascompletely
cooled off.
Otherwise, youmay burn yourself and/orfiremay break out
in fuel line.
• For safety during subsequent steps,thetension ofwires
should beslackened againsttheengine.
• Before disconnecting fuelhose, release fuelpressure from
fuel line.
Refer to"Releasing FuelPressure" inEC section.
• Besure tohoist engine andtransaxle inasafe manner.
• For engines notequipped withengine slingers, attach
proper slingers andbolts described inPARTS CATALOG.
CAUTION:
• When liftingengine, becareful nottostrike adjacent parts,
especially thefollowing: Accelerator wirecasing, brake
lines, andbrake master cylinder.
• Inhoisting theengine, alwaysuseengine slingers inasafe
manner.
Removal
1. Remove engineundercoverandhood.
2. Drain coolant frombothcylinder block,andradiator.
3. Drain engine oilfrom drain plugofoil pan.
4. Remove vacuumhoses,fuelhoses, wires,harness andcon-
nectors andsoon.
5. Remove exhausttubes,balljoints anddrive shafts.
6. Remove radiatorandfans.
7. Remove drivebelts.
8. Remove alternator, compressor andpower steering oil
pump fromengine.
9. Set asuitable transmission jackunder transaxle. Hoist
engine withengine slinger.
10. Remove centermember.
11. Remove enginemounting boltsfrombothsides andthen
slowly lowertransmission jack.

EM-99
•

OUTERCOMPONENT PARTS
Left side

SEC. 120.135.140.210.230

l"J
16•21 (1.6 .2.1. 12•
7

<, ~

~
/
7~

~ 16-21 (1.6 •2.1, 12•15)~~""

Ii] :
N.m (kg-m, in-Ib)
~ :N.m (kg-m, fl-Ib)
L

~-@@~
-@

~18•22 (1.8 -2.2, 13.16)

6

/

~~ ~2.75(6.3.7.6,46 -55)

SEM045FA

CD
Beltcover upper

@
Water pumppulley

@
Beltcover lower
@

Crankshaft pulley

@
Alternator

@
Alternator bracket

EM-114
(J)

Exhaust manifold

@
Gasket

@
Intake manifold

ENGINEMAINTENANCE
EXCEPT FORGA14DE ENGINE Checking
DriveBelts

•

~ 16-21
(1.6 •2.1, 12•15)

Alternator
SMA786CA
Without
airconditioner

Crankshaft
pUlley

~
25.5 -32.4 (2.60 -3.30, 18.8-23.9)

Compressor
Power steering
pump (or Idler pulley)

With
airconditioner

Idler
pulley
Crankshaft
pulley
Power
steering pump
(or Idler pulley)

~.
~6.3 -8.3 (0.64 -0.85, 55.6-73.8)

~ :Checking point

A :
N.m (kg-m, ft-lb)

III :
N.m (kg-m, in-Ib)

1.Inspect forcracks, fraying, wearoroil adhesion. If
necessary, replacewithanew one.
2. Inspect drivebeltdeflections bypushing onthe belt midway
between pulleys.

Adjust ifbelt deflections exceedthelimit.
Belt deflection:

Unit:mm(in)
Used beltdeflection
Deflectionofnew
Limit Deflection
after
belt

.
adjustment
Alternator With aircondi-

10(0.39) 6-7 (0.24 -0.28) 5.5
-6.5

lioner compressor
(0.217-0.256)

Without aircondi-

11(0.43) 7-9 (0.28 -0.35) 6-8 (0.24 -0.31)

lioner compressor
Power steering oil

7.5(0.295) 4
-6 (0.16 -0.24) 3-5 (0.12 -0.20)

pump
Applied pushing force
98

N
(10
kg,
22
Ib)

Inspect drivebeltdeflections whenengine iscold.
MA-17

ENGINEMAINTENANCE

Checking DriveBelts(Cont'd)
FOR GA14DE ENGINE

L
Idler pulley
Crankshaft
pulley
Withoutpowersteering
Idler
pulley locknut __
~ 25•32 (2.6 •3.3, 19-24)
)~'\c, ~ Crankshaft
'~~UlleY
~ ~\ Idlerpulley
Loosen

/
~
.

~~- - Withpower steering
SMA357CB

1. Inspect forcracks, fraying, wearoroil adhesion. If
necessary, replacewithanew one.
2. Inspect drivebeltdeflections bypushing onthe belt midway
between pulleys.

Adjust ifbelt deflections exceedthelimit.
Belt deflection:

Unit:mm(in)

Used beltdeflection
Deflectionofnew
Limit Deflection
alter
belt
adjustment
Alternator
With power steer-
11(0.43)
ing 7-9
6-8
Without power (0.28
-0.35)
(0.24-0.31)
steering 10
(0.39)
Air conditioner com-
9.5(0.374) 6
-8
5-7
pressor (0.24-0.31)
(0.20-0.28)
Power steering oil
7.5(0.295) 4-6
3-5
pump (0.16-0.24)
(0.12-0.20)
Applied pushing force
98N(10 kg, 22Ib)
Inspect drivebeltdeflections whenengine iscold.
MA-18

ENGINEMAINTENANCE
Checking DriveBelts
Crankshaft
pulley
With airconditioner Compressor Crankshaft
pulley
Without airconditioner

A:
N.m (kg-m, ft-Ib)
" :Check point
SMA808C
Used beltdeflection
Drive belts Deflection
Deflection
of
Limit afteradjust- new
belt
ment
Alternator
With airconditioner com-11.5
-12.5
6.5-7.5
7 -8
pressor (0.453
-
(0.28-0.31) (0.256
-
0.492) 0.295)
Without airconditioner
12-13
8-9
7-8
compressor (0.47-0.51)
(0.31-0.35)
(0.28-0.31)
6-7 4-53.5
-4.5
Power steering oilpump
(0.24-0.28)
(0.16-0.20) (0.138
-
0.177)
Applied pushing force
98N(10 kg,22Ib)
Unit:
mm(in)
1.
Inspect forcracks, fraying, wearoroil adhesion. If
necessary, replacewithanew one.
2. Inspect drivebeltdeflections bypushing onthe belt midway
between pulleys.

Adjust ifbelt deflections exceedthelimit.
Belt deflection:
Inspect drivebeltdeflections whenengine iscold.
SMA328C
Alternator
pulley

r

Crankshaft
/ pulley
Alternator
drive belt

<;:J

Engine
front
o

Engine
front
Altemetor
drivebeltfitting piece
(Modell withoutelrconditioner)
Alternator drivebelt
Set abelt inboth crankshaft
and alternator pulleysshown
in the figure.
MA-28

ENGINEMAINTENANCE

Air conditioner
compressor
SMA442C
AMA054 Manifold
NutCheck

1. Remove exhaustmanifold cover.
2. Tighten manifold boltsandnuts tothe specified torque.
Refer to"SERVICE DATAANDSPECIFICATIONS (SOS)".
3. Install exhaust manifold cover.

Checking DriveBelt

WARNING:
Inspect drivebeltdeflections whenengine iscold. When engine
is hot, check deflections atleast 30minutes afterengine has
been switched off.

1. Inspect beltsforcracks, fraying, wearoroil adhesion. If
necessary, replacewithnewones.
2. Inspect drivebeltdeflections bypushing onthe belt midway
between pulleys.
3. Adjust belt
deflection
if
it
exceeds thelimit.

Belt deflection:

Unit:mm(in)
Used beltdeflection
Deflectionofnew
Limit Deflection
after
belt
adjustment
Alternator 14(0.55) 11
-13 9-11
(0.43 -051) (0.35-0.43)
Air conditioner
14(0.55) 11
-13
9-11
compressor (0.43-051) (0.35-0.43)
Power steering oil
8(0.31) 5-7 (0.20 -0.28) 4-6 (0.16 -0.24)
pump
Water pump
without power

-
8(0.31) 6(0.24)
steering
Applied pushing
98N(10 kg,22Ib)
force

Inspect drivebeltdeflections whenengine iscold.
Changing EngineCoolant

WARNING:

To avoid thedanger ofbeing scalded, neverattempt tochange
the coolant whentheengine ishot.

1. Set heater "TEMP" controldialtothe max. "HOT" position.

• Make surethatairconditioner switchis"OFF".
MA-38

SERVICEDATAANDSPECIFICATIONS (SOS)
Engine Maintenance
Engine oilcapacity (Refillcapacity)

Unit:
r
(Imp qt)

INSPECTION
ANDADJUSTMENT
Drive beltdeflection
GA14DE engineexceptforEurope

Unit:mm(in)
With
oilfilter change
Without oilfilter change
3.2
(2-7/8)
2.8
(2-1/2)

•

Used beltdeflection
Deflection Deflection
of
Limit afteradjust- new
belt
ment
Alternator With air
6-7 55-6.5
conditioner 10(0.39)
(0.24-0.28)
(0.217-0.256)
compressor
Without air
7-9 6-8
conditioner 11(0.43)
(0.28-0.35) (0.24-0.31)
compressor
Power steering
7.5(0.295) 4
-6
3-5
oil pump
(0.16-0.24) (0.12-0.20)
Applied pushing
98N(10 kg, 22Ib)
force

GA14DE engineforEurope

Unit:mm(in)
Used beltdeflection
Deflection Deflection
of
Limit afteradjust- new
belt
ment
Alternator
With power
11(0.43)
steering
7-9
6-8
Without (0.28-0.35) (0.24-0.31)
power steer- 10(0.39)
ing
Air conditioner
9.5(0.374) 6
-8 5
-7
compressor (0.24
-0.31) (0.20-0.28)
Power steering
75(0.295) 4
-6 3-5
oil pump (0.16
-0.24)
(0.12-0.20)
Applied pushing
98N(10 kg,22Ib)
force
Coolant
capacity (Refillcapacity)
With reservoir tank

Unit:((Imp qt)
With heater Without
heater

M/T
5.9(5-1/4) 5.6(4-7/8)
A/T 6.4(5-5/8) 6.1(5-3/8)

Spark plug

GA16DE
&
GA14DE
GA16DE
&
GA15DE
engine forEurope engineexceptfor
and Israel EuropeandIsrael
Type Standard BKR5EBKR5E-11
Cold BKR6E,
BKR7E BKR6E-11,
BKR7E-11
Plug gap mm
(in) 0.8
-0.9 1.0
-
1.1

(0.031 -0.035) (0.039-0.043)

MA-53

SERVICEDATAANDSPECIFICATIONS (SOS)
INSPECTION ANDADJUSTMENT
Drive beltdeflection Engine
Maintenance
Engine oilcapacity (Refillcapacity)
Unit:
f
(Imp qt)
Unit:
f
(Imp qt)
Spark plug(Platinum-tipped type)
Coolant
capacity (Refillcapacity)
With reservoir tank
Withheater Withoutheater
MIT
6.1(5-3/8)
5.8(5-1/8)

AIT
6.6(5-718) 6.3(5-1/2)

Reservoir tank
07(5/8)
3.4
(3)

3.2 (2-7/8)

With
oilfilter change
Without oilfilter change
Unit:
mm(in)
Used beltdeflection
Deflection Deflection
of
Limit afteradjust- new
belt
ment
Alternator With aircon-
11.5-12.5 7-8 6.5-7.5
ditioner com-
(0.453-0.492) (0.28
-0.31) (0.256-0.295)
pressor
Without air
12-13 8-9 7-8
conditioner
(0.47-0.51) (0.31-0.35) (0.28-0.31)
compressor
Power steering 6-7 4-5 3.5-4.5
oil pump (0.24-0.28) (0.16-0.20) (0.138-0.177)
Applied pushing
98N(10 kg,22Ib)
force
Make
Type
Standard
Alternative NGK
PFR58-11
PFR68-11 PFR78-11
MA-54

SERVICEDATAANDSPECIFICATIONS (50S)

Used beltdeflection
Deflection Deflection
of
Limit afteradjust- new
belt
ment
Alternator 14(055) 11
-13 9-11
(0.43 -0.51)
(0.35-0.43)
Air conditioner
14(0.55) 11
-13
9-11
compressor (0.43
-0.51)
(0.35-0.43)
Power steer-
8(0.31) 5
-7
4-6
ing oilpump (0.20-0.28)
(0.16-0.24)
Water pump
without power

-
8
(0.31) 6(0.24)
steering
Applied push-
98N(10 kg, 22Ib)
ing force

Coolant capacity (Refillcapacity)
INSPECTION
ANDADJUSTMENT
Drive beltdeflection

Unit:kPa(bar, kg/cm', psi)
12,749 (127.5, 130,1,849)
Without
oilfilter
With oilfilter
Injection pressure

Injection
nozzle
Idle speed

Unit:rpm
Standard
M/T
700

'go

800'
': Air conditioner "ON"

TIGHTENING TORQUE

Unit N'mkg-m
ft-Ib in-Ib
Manifold nuts
&

18-22
1.8-2.2
bolts 13
-16
Rocker cover
2-4
0.2-0.4 1.4-2.9 17-35
screw
Alternator, power
steering mounting 62-75
6.3-76 46
-55
bolt
Alternator, power
steering adjuster 16
-21
1.6-2.1
12-15
lock bolt
Cylinder block
54-74
5.5-7.5 40
-54
drain plug
Engine oilpan
29-39 3.0-4.0 22-29
drain plug
Injector (Tohead)
59-69 6.0-7.0 43-51
Spill tube 39-49
4.0-5.0 29-36
Delivery tube 22-25 2.2-2.5
16-18

Engine
Maintenance
Engine oilcapacity (Refillcapacity)

Unit:[(Imp qt)•
46 (4)

51 (4--1/2)

Unit:
mm(in)
Unit:
f
(Imp qt)
5.2 (4-5/8)
49 (4-3/8)
0.7 (5/8)
Unit: kPa(bar, kg/cm', psi)
78 -98
(0.78 -0.98, 08-1.0, 11-14)
59 -98
(0.59 -0.98, 06-10, 9-14)
157 (1.57, 1.6,23)
Standard
Limit
With
heater
Without heater
Reservoir tank
Radiator caprelief pressure
Radiator testingpressure

Cooling
systemcheck
MA-55