trunk release NISSAN ALTIMA COUPE 2009 D32 / 4.G Quick Reference Guide
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2009, Model line: ALTIMA COUPE, Model: NISSAN ALTIMA COUPE 2009 D32 / 4.GPages: 36, PDF Size: 5.3 MB
Page 4 of 36
NISSAN INTELLIGENT KEY™
The NISSAN Intelligent Key™ system allows you to lock or unlock
your vehicle, open your trunk and start the engine.
NOTE: It is important to make sure the Intelligent Key is with you
(that is, in your pocket or purse) . The operating range of the door and trunk lock/unlock func-
tion is approximately 31 in (0.8 m) .
Locking the vehicle - Push any door handle Request Switch
(if so equipped)
once.
Unlocking thevehicle -Push anydoor handle Request
Switch (ifso equipped)
once. Thecorresponding
door willunlock. Pushthedoor handle Request
Switch
again within 1minute; allother doors will
unlock.
OPENING THE TRUNK
To open the trunk using the Request Switch (if so equipped) ,
your Intelligent Key must be with you.
Push the Request/Release Switch (if so equipped)
un-
der the trunk handle.
Lift up on the trunk lid to fully open the trunk.
STARTING THE ENGINE
Depress the brake pedal (CVT) or clutch pedal (MT) .
Push the ignition switch to start the engine.
TURNING THE ENGINE OFF
Shift the shift selector to the P (Park) position (CVT) or to
the N (Neutral) position (manual transmission) and apply the
parking brake.
Push the ignition switch to turn the engine off.
NISSAN INTELLIGENT KEY™ BATTERY DISCHARGE
If the battery of the Intelligent Key is almost discharged, the
guide lightofthe Intelligent Keyport blinks andtheIntelli-
gent Keyinsertion indicator isdisplayed inthe vehicle
information display.
Tostart theengine underthesecircumstances, insertthe
Intelligent Keyinto thekey port inthe direction indicated
until it latches into place.
To remove the Intelligent Key from the port, push the ignition
switch to turn the engine off and pull the Intelligent Key out of the port.
The Intelligent Key port does not charge the Intelligent Key battery. If you see the low
battery indicator, replace the battery in the Intelligent Key.
2
Page 16 of 36
TRUNK LID CANCEL SWITCH
When the cancel switch (located inside the glove box)
is OFF, the trunk lid cannot be opened with the trunk lid
opener (located onthe instrument panel) ,thetrunk
Request Switch button (if so equipped) or the Intelli-
gent Key button.
It can be opened by using the Emergency Inside Trunk
Release.
MOONROOF CONTROLS (if so equipped)
The ignition switch must be in the ON position to operate
the moonroof controls.
TILTING THE MOONROOF
To tiltthe moonroof up,push thetiltswitch toward
the
position.
To tilt the moonroof down, push the tilt switch toward
the
position.
SLIDING THE MOONROOF
To fully open the moonroof, push the switch toward theposition.
To fully close the moonroof, push the switch toward the
position.
To open orclose themoonroof partway, push theswitch ineither direction (
or) while the moonroof is sliding to stop it in the desired position.
FRONT SEAT ADJUSTMENTS
With manual seats (if so equipped):
FORWARD AND BACKWARD
Pull the center of the bar up
under the front of the
seat andhold itwhile youslide theseat forward or
backward. Release the bar to lock the seat in position.
SEAT LIFTER (driver’s seat, if so equipped)
Pull up or push down the adjusting lever
repeat-
edly to adjust the seat height.
RECLINING
Lift the lever
on the side of the seat to adjust the seatback forward or backward.
Release thelever when youhave found acomfortable angleandtheseat beltfits
properly.
14
Page 18 of 36
FOLDING DOWN THE REAR SEATS
FROM INSIDE THE VEHICLE The rear seats canbelocked usingthemechanical keyto
prevent unauthorized access.
Open the access cover and press the release button
to
fold down the center/passenger’s side rear seat.
Reach through the opening and pull on the strap
located
behind the seat to fold down the driver’s side rear seat.
FROM THE TRUNK
Pull thestrap
located behindtheseat tofold down the
center/passenger’s side rear seat.
Pull on the strap
located behind the seat to fold down the
driver’s side rear seat.
HOMELINK UNIVERSAL TRANSCEIVER (if so equipped)
SYSTEM OPERATING TIPS
Garage doors, electrical gates, entry doors, etc. will be activated during programming.
To avoid injury, make sure that people and objects are clear of all doors or gates during
programming. Yourvehicle’s engineshouldbeturned offwhile programming the
HomeLink Transceiver.
To program your HomeLink Transceiver to operate a garage door, gate, or entry door
opener, home or office lighting, you need to be at the same location as the device.
NOTE: Garage dooropeners (manufactured after1996) have“rolling codepro-
tection”. Toprogram agarage dooropener equipped with“rolling codeprotec-
tion”, you will need to use a ladder to get up to the garage door opener motor to
be able to access the “smart” or “learn” program button.
PROGRAMMING YOUR HOMELINK UNIVERSAL TRANSCEIVER (Mirror,
Sun Visor or Overhead Console)
1. To begin, pressandhold thetwo
outer HomeLink buttons(toclear
the memory) until the indicator light
blinks slowly (after20seconds) .
Release both buttons.
2. Position theend ofthe hand-held
transmitter 1-3 in (26-76 mm) away
from the HomeLink surface.
16