lock NISSAN GT-R 1998 Workshop Manual

REMOTE CONTROL ENTRY SYSTEM
ID Code Entry Procedure
Enter the identity (ID) code manually when:
remote controller or control unit is replaced.
an additional remote controller is activated.
To enter the ID code, follow the procedures below.
PROCEDURE
I Close all doors and lock driveis side door. I
Insert and remove the key from the ignition more than six times within 10 seconds.
(Power door lock will then unlock.)
Within
3 seconds after door lock is unlocked, turn ignition key switch to "ACCn posi-
tion and lock the driver's side door.
At this time, the original ID codes are erased.
Push any button on the new remote controller once. (Power door lock will then
unlock.)
At this time, the new ID code is entered. e
Lock driver's side door.
Do you
want to enter any additional remote controller ID codes?
A maximum four ID codes may be entered. Any attempt to enter more will be
ignored.
I Open driver's side door or turn the ignition key switch to 'OFF position. I
No
END.
After entering the identity (ID) code, check the operation of remote control
entry system.
Yes
NOTE
If you need to activate more than two additional new remote controllers, repeat the procedure
"Additional ID code entry" for each new remote controller.
If the same ID code that exists in the memory is input, the entry will be ignored.
Entry of maximum four ID codes is allowed and any attempt to enter more will be ignored.

IGNITION KEY-OPERATED ILLUMINATION SYSTEM
Behind combination meter Component Parts Location
Meter control unit
Circuit Diagram
7, . .
& Driver door lock detection switch
T
2 1 r Passenger door SW Rear RH door SW 326
' a
Rear LH door SW
3 - -
Room lamp
IGN SW illumination
TK24 (Brown) TK20 (Brown) TK20 (White) EL-2 178D I 1 J
Meter Control Unit Input/Output Signal
Terminal No.
Specifications I I
Specification
Approx.
OV
Approx. 12V
Approx. OV
Approx. 5V
Approx. 12V
Approx. OV
Approx. 12V
Approx. 12V
Approx. OV
Approx. 12V
Approx. OV
Approx. OV
Approx. 12V
Approx. OV'
Approx. 12V
Measuring condition
Signal name Ignition
Operation or condition
switch
Driver door switch ON (Open)
OFF Driver door switch
signal OFF (Closed)
Driver door lock
sig-
Door is unlocked. (Switch ON)
nal OFF
Door is locked. (Switch OFF)
Battery OFF
-
Open a door. (ON)
Door switch signal
OFF
Close all the doors. (OFF)
Ignition power supply ON
-
Key-in detection Remove
the ignition key.
switch signal OFF
Insert the ignition key.
Ground ON
-
OFF Room lamp switch:
Insert the ignition key. Each door switch
Room lamp, ignition Neutral position ON
(Open)
OFF (Closed)
switch illumination
Remove the ignition key from the
signal
- lamp switch: Close all the doors. key cylinder.
Neutral position
Turn the ignition switch ON.

ENGINE MECHANICAL I RB~ODE (UB) ]
STANDARD AND REPAIR LIMIT
Firing order I 1-5-3-6-2-4
Compression pressure
MPa
(kg/cm2)/rpm
Distortion limit mm
- - -- --- - Ignition advance device
Electronically-controlled ignition advance
Engine
oil capacity
e
Spark plug standard
Limit
. Limit
of variation between cylinders
Intake manifold
Intake manifold collector
Exhaust manifold
Cylinder head
Cvlinder block
lgnition timing (during no feed back control) 1.23
(1 2%)/300
0.93 (9.5)1300
0.1 (1.0)/300
0.1 0.1
0.3
0.2
0.1
Without filter
With filter
MakerlTypeISpark
plug gap mm
Engine idling speed
W'
Idle base speed (during no feed back control)
rPm
Density of
COIHC at idling speed
Wppm Approx.
3.8
Approx. 4.2
NG WPFR5G-11 11.0
- 1
-1
650-.50
(N or P position for
A/T)
600 (N or P position for AlT)
Less than O.l/Less than 50
I New I Used I Limit
Valve
clearance
(INTIEXH)
mm
Deflection
amount of accessory V-belt
Measured with tension gauge
N (kg) Hot
engine
.
Cold engine (at ambient temperature)
Measured by pushing at 98 N (10 kg)
mm 0.36+0.062/0.53+0.062
0.31 1~,0.04/0.50i0.04
Fuel tank capacity
e
Engine coolant total capacity [with reservoir tank (max. level)] e
Thermostat opening temperature [start to open - full open]
"C
Radiator cap opening pressure
MPa (kg/cm2) Approx.
65
Approx. 9.4 82 - 95
0.06
- 0.1 0 (0.6 - 1 .O)
A/C compressor belt
Power
steering pump belt
Fan belt
Power steering pump belt
1 8-10 1 10-12 1 16
667
- 755
(68
- 77)
A/C compressor belt 1 6-8 1 7-9 / 12
Fan belt
1 3-5 1 4-6 1 7.5
559 - 637
(57
- 65)
SEC.117 Power steering
Fan belt pump be1 t
284 (29)

ENGINE MECHANICAL [ RB20DE (UB) 1
TIGHTENING TORQUE
Unit: N.m (kg-m)
Engine cover
Throttle body
Throttle position sensor
IAA unit (ACC valve)
lntake manifold collector
(upper)
Intake manifold collector
Intake manifold
Vacuum tank
Engine coolant temperature
sensor
- --
' Fuel tube
Pressure regulator
Fuel damper
Fuel hose clamp bolt
(in engine compartment)
Exhaust manifold cover
' Exhaust manifold
Oxygen sensor
Crank pulley
Cam pulley (INT)
Cam pulley
(EXH)
Timing belt cover
Timing belt rear cover
Tensioner pulley
Idler pulley
Crankshaft position sensor
' Oil pan
Oil strainer
Oil pan drain plug
ignition coil
Spark plug
* Rocker cover
Camshaft bracket
Camshaft baffle plate 5.1
- 6.5 (0.52 - 0.66)
20
- 29 (2.0 - 3.0)
1) 5.5 - 7.5 (0.56 - 0.76)
?) 5.5 - 7.5 (0.56 - 0.76)
:Tighten separately in twice.)
Cylinder head bolt
Cylinder head sub bolt
VTC solenoid
' Main bearing cap
Connecting rod nut
Flywheel and drive plate
Engine coolant drain plug
Knock sensor
Radiator mounting bracket
Auxiliary electric fan
Water pump (M6 bolt)
(M8 bolt)
(MI 0 bolt)
Water inlet
Oil pump assembly
Accelerator cable
lock nut
Fuel tank strap
Fuel sender unit lock
ring
Exhaust manifold to front
tube Front tube to catalytic
converter Catalytic converter to cent
tube Center tube to main
muffler
Alternator (main)
(stay side)
Starter motor Unit:
N-m (kg-m)
1)
29 (3.0)
2) 98 (10.0)
3)
0
(0)
4) 25
- 34 (2.5 - 3.5) GI
5) 95" - 100"
(Angle tightening)
Ec
9.0 - 12 (0.92 - 1.2)
25
- 34 (2.5 - 3.5)
49
- 59 (5.0 - 6.0) h$7'
1) 14 - 16 (1.4 - 1.6)
2) 45"
- 50"
(Angle tightening)
BW
93 - 103 (9.5 - 10.5)
34 - 44 (3.5 - 4.5)
25
- 34 (2.5 - 3.5) ST
': Tighten as specified tightening order.
1): Tighten separately in several times.

ENGINE MECHANICAL
STANDARD AND REPAIR LIMIT
Firing order
Compression pressure
MPa (kg/cm2)/rpm
-
Intake manifold
Intake manifold collector
--- - Standard Limit
Limit of variation between
cylinders
0.1
0.1
Distortion limit mm
Engine oil capacity
P
Spark plug
Deflection amount of accessory
V-belt Power steering pump
belt
I
- -- - - 1.26 (1 2.8)/300
0.96 (9.8)/300
0.1
(1 .OY300
Measured with tension gauge Exhaust
manifold
Cylinder head
Cylinder block
Without filter
With filter
MakerKype/Spark
plug gap
mrn
I "
650.-50 (N or P position for CVT)
600 (N or P position for AIT)
Less than O.l/Less than 50
15U600
0.36~0.06210.53~0.062
0.31 -.0.04/0.50~0.04
Approx. 65
Approx. 9.4
82 - 95
0.06 - 0.10 (0.6 - 1 .O)
"
Engine idling speed rpm
Idle base speed (during no feed back control)
rpm
Density of
COIHC at idling speed
%/ppm
Ignition timing (during no feed back control)
BTDCO/rpm
I NC compressor err
0.3
0.2
0.1
Approx. 3.8
Approx. 4.2
NGWPFR5G-11/1.0
- 1.1
lanition
advance device
1
Valve clearance (INTIEXH) mm
(kg)
/ Fan belt Electronicallv-controlled
ianition
advance
Hot engine
Cold engine (at ambient temperature)
I power steerina DU~D belt 1 8-10
Fuel tank capacity
Q
Engine
coolant total capacity [with reservoir tank (max. level)] e
Thermostat opening temperature [start to open - full open] OC
Radiator cap opening pressure
MPa (kg/crn2)
,
I Fan belt 1 3-5
Measured
by pushing at 98
N (10 kg)
mm
I SEC.! I7 Power steering I
*I I 1
AK compressor belt 1 6-8
Fan belt pump beit
Used 1 Limit

ENGINE MECHANICAL
TIGHTENING TORQUE
Engine cover
' Throttle body
Throttle position sensor
IAA unit (ACC valve)
' Intake manifold collector
(upper)
' Intake manifold collector
Intake manifold
Vacuum tank
Engine coolant temperature
sensor
' Fuel tube
Pressure regulator
Fuel damper
Fuel hose clamp bolt
(in engine compartment)
Exhaust manifold cover
Exhaust manifold
Oxygen sensor
Crank pulley
Cam pulley (INT)
Cam pulley
(EXH)
Timing belt cover
Ttming belt rear cover
Tensioner pulley
Idler pulley
Crankshaft position sensor
' Oil pan
Oil strainer
Oil pan drain plug
Ignition coil
Spark plug
Rocker cover
* Camshaft bracket
Camshaft baffle plate Unit:
Nm (kg-m)
5.0
- 6.5 (0.51 - 0.66)
1) 8.8
- 11 (0.9 - 1.1)
2) 18
- 22 (1.8 - 2.2)
2.0
- 2.4 (0.20 - 0.24)
8.4
- 11 (0.86 - 1 .I)
18
- 22 (1.8 - 2.2)
5.1
- 6.5 (0.52 - 0.66)
20
- 29 (2.0 - 3.0)
1) 5.5 - 7.5 (0.56 - 0.76)
2) 5.5 - 7.5 (0.56 - 0.76)
:Tighten separately in twice.)
Cylinder head bolt
Cylinder head sub bolt
VTC solenoid
Main bearing cap
Connecting rod nut
Flywheel and drive plate
Engine coolant drain plug
Knock sensor
Radiator mounting bracket
Auxiliary electric fan
Water pump
(M6 bolt)
(M8 bolt)
(M 1 0 bolt)
Water inlet
Oil pump assembly
-
Accelerator cable lock nut
Fuel tank strap
Fuel sender unit lock
ring
Exhaust manifold to front
tube
Front tube to catalytic
converter
Catalytic converter to center
tube Center tube to main
muffler
Alternator (main)
(stay side)
Starter motor Unit:
N.m (kg-m)
1) 29 (3.0)
2) 98 (10.0) 3) 0 (0)
@
4)
25 - 34 (2.5 - 3.5)
5) 95" - 100"
(Angle tightening)
E
9.0 - 12 (0.92 - 1.2)
25
- 34 (2.5 - 3.5) j$? 49 - 59 (5.0 - 6.0)
1) 14- 16
(1.4- 1.6)
2) 60"
- 65" BR
(Angle tightening)
93
- 103 (9.5 - 10.5)
34 - 44 (3.5 - 4.5)
25
- 34 (2.5 - 3.5) a=
': Tighten as specified tightening order.
1): Tighten separately in several times.

ENGINE MECHANICAL
STANDARD AND REPAIR LIMIT
Distortion limit mm
- - Intake manifold
Intake manifold collector
1 -5-3-6-2-4
1.20 (1
2.2)/300
0.90 (9.2)/300
0.1 (1.0)/300
Firing order
-- - 0.1
0.1
- -- - ( Cylinder block 0.1
Compression
pressure
MPa
(kg/cm2)/rpm
Exhaust manifold
Cvlinder head
Engine oil capacity Standard
Limit
-
Limit of variation between cylinders
0.3
0.2
- - -- - Spark plug I ~akerfl~~e/~~ark plug gap mm r NGKPFRGG-11/1.0 - 1.1
Without
filter
'with
filter
ignition advance device
I Electronically-controlled ignition advance
Approx.
3.9
Aoorox.
4.3
Engine idling speed
rPm
Idle
base speed (during no feed back control)
Pm
650-e50
(N or P position for
A/T)
600 (N or P position for AQ
Density of COIHC at idling speed
Wppm
Ignition timing (during no feed back control)
BTDCO/rpm Less
thanbl~ess than 50
15dY600
Valve clearance
(INT/EXH) mm
Deflection amount of accessory V-belt Hot
engine
Cold engine (at ambient temperature)
Measured
with tension gauge
(kg)
I
SEC.117 Power steering
Fan belt pump belt
0.36+0.062/0.53i0.062
0.3
1 20 .04/0.50a0.04
Fuel tank capacity
4
Engine coolant total capacity [with reservoir tank (max. level)] t
Thermostat opening temperature [start to open - full open]
OC
Radiator cap opening pressure
MPa (kg/cm2)
Power steering pump belt
Measured by pushing at 98
N (1 0 kg)
mm Approx.
65
Approx. 9.4
82
- 95
0.06
- 0.1 0 (0.6 - 1 .O)
New 1 Used 1 Limit
AfC
compressor belt
Fan belt
,
667 - 755
(68
- 77)
Power steering pump belt
' AfC compressor belt
Fan belt
559 - 637 284 (29)
(57 - 65)
667
- 755
(68
- 77)
667
- 755
(68
- 77)
559 - 637 284 (29)
(57 - 65)
559 - 637 284 (29) (57 - 65)
8-
10
6-8
3 - 5
- 10 - 12 16
7-9 12
4
- 6 7.5

ENGINE MECHANICAL pEZBq
TIGHTENING TORQUE
Engine cover
' Throttle body
Throttle position sensor
IAA unit
(ACC valve)
' Intake manifold collector
* Intake manifold
Engine coolant temperature
sensor
' Fuel tube
Pressure regulator
Fuel damper
Fuel hose clamp bolt
(in engine compartment)
Turbocharger Oil tube
Water tube (block side)
(turbocharger side)
Oxygen sensor
Exhaust manifold cover
' Exhaust manifold
Crank pulley
Cam pulley (INT)
Cam pulley
(EXH)
Timing belt cover
Timing belt rear cover
Tensioner pulley
Idler pulley
Crankshaft position sensor
' Oil pan
Oil strainer
Oil pan drain plug
Ignition coil
Spark plug
' Rocker cover
' Camshaft bracket
Camshaft baffle plate Unit:
N.m (kg-m)
5.0
- 6.5 (0.51 - 0.66)
1)
8.8
- 11 (0.9 - 1.1)
2)
18
- 22 (1 -8 - 2.2)
2.0
- 2.4 (0.20 - 0.24)
8.4
- 11 (0.86 - 1.1)
18
- 22 (1.8 - 2.2)
18
- 22 (1 -8 - 2.2)
20
- 29 (2.0 - 3.0)
5.1
- 6.5 (0.52 - 0.66)
20
- 29 (2.0 - 3.0)
1) 5.5
- 7.5 (0.56 - 0.76)
2) 5.5 - 7.5 (0.56 - 0.76)
(Tighten separately in twice.)
' Cylinder head boit
Cylinder head sub bolt
VTC solenoid
" Main bearing cap
Connecting rod
nut
Oil jet
Flywheel and drive plate
Engine coolant drain plug
Knock sensor
Radiator mounting bracket
Auxiliary electric fan
Water pump (M6 bolt)
(M8 bolt)
(MI
0 bolt)
Water inlet
Oil pump assembly
Accelerator cable lock nut
Fuel tank strap
Fuel sender unit lock
ring
Exhaust manifold to front
tube
Front tube to catalytic
converter
Catalytic converter to center
tube
Center tube to main
muffler
Alternator (main)
(stay side)
Starter motor Unit:
N.m (kg-m)
1) 29 (3.0)
2) 98 (10.0)
3) 0 (0)
4) 25 - 34 (2.5 - 3.5)
5) 95"
- 100"
(Angle tightening)
I%
9.0 - 12 (0.92 - 1.2)
25
- 34 (2.5 - 3.5)
49
- 59 (5.0 - 6.0) AT
1) 14 - 16 (1.4 - 1.6)
2) 60" - 65"
(Angle tightening) BR
30 - 40 (3.1 - 4.1)
93
- 103 (9.5 - 10.5)
34 - 44 (3.5 - 4.5) ST
25 - 34 (2.5 - 3.5)
3.8
- 4.5 (0.39 - 0.46) I%$
5.1 - 6.5 (0.52 - 0.66)
17
- 21 (1.7 - 2.1)
20
- 23 (2.0 - 2.3) kIA
35 - 47 (3.6 - 4.8)
16
- 21 (1.6 - 2.1)
9.0
- 12 (0.92 - 1.2) a=
': Tighten as specified tightening order.
1): Tighten separately in several times.

AUTOMATIC TRANSMISSION
LOCK-UP SPEED
Engine type (mode
Vehicle speed in
D, position
Vehicle speed in
D, position code)
Lock-up OFF krnh
Lock-up
ON
kmlh
Lock-up OFF kmlh Closed throttle
Half throttle
Closed throttle
Half throttle
Closed throttle Half throttle
Closed throttle Half throttle
--- - Closed throttle: Throttle opening of less than 118 with the closed throttle position switch off position
Half throttle: Throttle opening of 418
STALL SPEED
LINE PRESSURE
Engine type (model code) Stall engine speed rpm
- - -
At idle engine speed I 0.58 - 0.62 (5.9 - 6.3) I 0.47 - 0.51 (4.8 - 5.2)
Engine speed
At stall engine speed
1 1.71 - 1.78 (17.4 - 18.2) 1 1.22 - 1.29 (12.4 - 13.2)
Line pressure MPa (kg/cm2)
R position D, 2, and 1 positions (4AT)
D, 3, and 2 positions (M-AT)

CONTROL VALVE SPECIFICATIONS
Val ve loc
Upper body
Lower body :ation
L1
L2
L3
L4
L5
L6
CONTROL VALVE SPRING SPECIFICATIONS
L7
L8
L9
L10
L11
L13
L14
L15
L16
Unit: mm I 1 I I I I
Valve designation
Torque converter regulator valve
Pressure modifier valve
Pressure regulator valve
Overrun clutch control valve
Lower body Total
length mm
27.5
43.5
68.0
55.5
19.5
56.0
75.0
Accumulator control valve Parts
number
31780 41x01
31751 41x02
31741 80x00
3 1 772
4AXOO
3 1 772
4AX02
31 675 41 X07
31766
- 4AXOO
31766 51x03
4AX03
model
Except
4AX03 model
4AX03 model
Except
4AX03 model
Valve
spring location Throttle accumulator piston
Shift valve
B
Shift valve A
Upper body
Overrun clutch reducing
63.5
65.0
Overrun clutch reducing valve
Pilot valve
Torque converter clutch control valve
L1
L2 L3
L4
L5
L6
L7
Valve spring designation
Torque converter regulator valve spring
Pressure modifier valve spring
Pressure regulator valve spring
Throttle accumulator piston spring
A
Shift valve B spring
Shift valve
A spring
31 766 51 X04
31766 4AX02
54.5
38.5 58.0
57.0
67.0
37.5
37.5
41
.O
66.0 38.5
Shuttle shift valve S
Free length
36.0
31.95
31.8
30.5
23.5 25.0
23.6
38.3
Overrun clutch control valve
spring
4AX03 model
Pilot valve spring
r
Torque converter clutch control valve spring
31 772 41 X06
31772 41x01
31 832
4AX01
31766 51x05
31766 4AX01
31772 41x12
31772 4AX01
31772 71x00
31 772 41 X03
31772
21x00
4AX03
model
Except
4AX03 model
4AX03 model
Except
4AX03 model
/ L~ / valve spring
26.5
46.5
54.0
25.0
22.6
25.4
23.0
23.0
33.89
I
I I
Shuttle shift valve S spring
1 reducing valve spring Outer
diameter
'D"
9.0
6.8
15.0
9.8
11.0
7.0
7.0
8.0
Except 4AX03 model
32.5
4AX03
model
Except
4AX03 model
4AX00 model
Except
4AX00 model
1 reducing valve
9.0
6.5
5.65
7.0
6.7
6.75
6.7
6.7
6.95
3-2
timing
valve spring
Servo charger valve spring
Lock-up regulator valve spring
3-2 timing valve
Wire
diameter
"d"
1.4
0.8 1.3
1.3
0.8
0.65
0.6
0.55
35.5 7.0
4AX03
model
Except
4AX03 model
1.1
0.8
0.75
0.65 0.7
0.75
0.7
0.7
0.55
Servo charger valve
Lock-up regulator valve
Winding
direction Right
4
1
7
t
?
T
T
7.0 0.85
T
?
T
T
?
T
T
T
.. I
Parts
number
31742
4AXOO
3 1 742
41x19
31742
4AXO 1
31 742
41
XI 5
31742
4AX02
3
1762
41x01
3 1762
41x03
31762
4AXOO
0.9
T 31742
t
41 X63
31742
41x65