reset NISSAN GT-R 2022 Owner's Guide

Do not use the cruise control when
driving under the following condi-
tions. Doing so could cause a loss of
vehicle control and result in an acci-
dent.
.When it is not possible to keep
the vehicle at a set speed.
. In heavy traffic or in traffic that
varies in speed.
. On winding or hilly roads.
. On slippery roads (rain, snow, ice,
etc.).
. In very windy areas.
NOTE:
. When the SAVE mode is selected
with the transmission setup switch,
the acceleration and deceleration
can be controlled smoothly. When
the SAVE mode is selected, the
maximum setting speed is lower
than the one in the normal mode. When the vehicle approaches a gen-
tle uphill, there may be a slight delay
as the vehicle returns to the preset
speed. However, the vehicle will
gradually accelerate and return to
the preset speed.
PRECAUTIONS ON CRUISE CON-
TROL.
If the cruise control system malfunc-
tions, it will cancel automatically. The
SET indicator will blink and the cruise
control system warning will appear to
warn the driver. (
“Cruise control
system warning” page 2-43)
. If the engine coolant temperature
becomes excessively high, the cruise
control system will be canceled auto-
matically.
. If the SET indicator blinks, turn the
cruise control main switch off and it is
recommended you contact a GT-R
Starting and driving
5-35
CRUISE CONTROL

2. Accelerate your vehicle to the desiredspeed, push the SET/COAST switch
and release it. (The SET indicator will
illuminate in the meter.) Take your
foot off the accelerator pedal. Your
vehicle will maintain the set speed.
NOTE:
If the vehicle speed reaches approxi-
mately 3 MPH (5 km/h) over the set
speed, the set speed on the vehicle
information display blinks.Passing another vehicleTo pass another vehicle, depress the
accelerator pedal. When you release the
pedal, the vehicle will return to the pre- viously set speed.
Increasing the set vehicle speedTo reset at a faster cruising speed, use
one of the following methods:
.
Depress the accelerator pedal. When
the vehicle attains the desired speed,
push and release the SET/COAST
switch.
. Push and hold the RESUME/ACCELER-
ATE switch. When the vehicle attains
the speed you desire, release the
switch.
. Push and then quickly release the
RESUME/ACCELERATE switch. Each
time you do this, the set speed will
increase by about 1 MPH or 1 km/h.Decreasing the set vehicle speedTo reset at a slower cruising speed, use
one of the following methods:
.Lightly tap the brake pedal. When the
vehicle attains the desired speed,
push and release the SET/COAST
switch.
. Push and hold the SET/COAST switch.
Release the switch when the vehicle
slows down to the desired speed.
. Push and then quickly release the
Starting and driving
5-37

. The SET
indicator will turn off.
. Tap the brake pedal. The SET
indicator will turn off.
. Turn the MAIN switchoff. Both the
CRUISE indicator and SET indicator will
turn off. NOTE:
.
If cruise control was canceled by
pressing the cancel switch or by
depressing the brake pedal, the
system changes to standby status.
. If you depress the brake pedal while
pushing the RESUME/ACCELERATE
or SET/COAST switch and reset at
the cruising speed, the cruise control
will be deactivated. Turn the MAIN
switch off once and then turn it on
again.
Under the following conditions, cruise
control will be automatically canceled.
. Vehicle speed drops to below approxi-
mately 19 MPH (30 km/h).
. Vehicle speed drops to more than
approximately 8 MPH (13 km/h) below
the set vehicle speed.
. The shift lever is moved to a position
other than

operates to prevent one drive wheel from
slipping by transferring power to a non
slipping drive wheel. The VDC warning
light
will not flash. The VDC
system is automatically reset to on when
the ignition switch is placed in the off
position then back to the on position.
(
“Vehicle Dynamic Control (VDC)
warning light” page 2-34,
“Vehicle
Dynamic Control (VDC) off indicator light”
page 2-33)
The computer has a built-in diagnostic
feature that tests the system each time
you start the engine and move the vehicle
forward or in reverse at a slow speed.
When the self-test occurs, you may hear a
“clunk” noise and/or feel a pulsation in the
brake pedal. This is normal and is not an
indication of a malfunction.
may illuminate.
. If brake related parts such as
brake pads, rotors and calipers
are not standard equipment or
are extremely deteriorated, the
VDC system may not operate
properly and the VDC warning
light
may illuminate.
. If engine control related parts are
not standard equipment or are
extremely deteriorated, the VDC
warning light
may illuminate.
. When driving on extremely in-
clined surfaces such as higher
banked corners, the VDC system
may not operate properly and the
VDC warning light
may illumi-
nate. Do not drive on these types of roads.
. When driving on an unstable sur-
face such as a turntable, ferry,
elevator or ramp, the VDC warn-
ing light
may illuminate. This
is not a malfunction. Restart the
engine after driving onto a stable
surface.
. If wheels or tires other than the
those recommended are used,
the VDC system may not operate
properly and the VDC warning
light
may illuminate.
. The VDC system is not a substi-
tute for winter tires or tire chains
on a snow covered road.
NOTE:
. Always make sure the VDC is ON
before driving the vehicle by check-
ing that the VDC OFF indicator lights
on the meter and the VDC set-up
switch are not illuminated.
The GT-R is a high performance
vehicle and the VDC must be on/
activated to provide proper power-
train operation and intended driva-
bility.Starting and driving
5-55

.You can also check the pressure of all
tires on the touch screen display.
Refer to the separate Multi Function
Display Owner’s Manual.
. The tire pressure sensor should be
reset anytime the wheels or tires are
removed or replaced.
. If the tire is removed in order to
replace the tire pressure sensor bat-
tery, it may not be possible to reuse
the removed tire from the wheel. To
replace the tire pressure sensor bat-
tery, it is recommended you contact a
GT-R certified NISSAN dealer.
WARNING
.If the low tire pressure warning
light illuminates while driving,
avoid sudden steering maneu-
vers or abrupt braking, reduce
vehicle speed, pull off the road
to a safe location and stop the
vehicle as soon as possible. Driv-
ing with under-inflated tires may
permanently damage the tires
and increase the likelihood of tire
failure. Serious vehicle damage
could occur and may lead to an
accident and could result in ser-
ious personal injury. Check the tire pressure for all four tires.
Adjust the tire pressure to the
recommended COLD tire pressure
shown on the Tire and Loading
Information label to turn the low
tire pressure warning light off. If
the light still illuminates while
driving after adjusting the tire
pressure, a tire may be flat
(
“Run-flat tires” page 6-4) or
the TPMS may be malfunctioning.
If no tire is flat and all tires are
properly inflated, have the vehicle
checked. It is recommended you
have the vehicle checked by a
GT-R certified NISSAN dealer.
. Although you can continue driv-
ing with a punctured run-flat tire,
remember that vehicle handling
stability is reduced, which could
lead to an accident and personal
injury. Also, driving a long dis-
tance at high speeds may da-
mage the tires.
. Do not drive at speeds above 50
MPH (80 km/h) and do not drive
more than 50 miles (80 km) with a
punctured run-flat tire. The actual
distance the vehicle can be driven
on a flat tire depends on outside
temperature, vehicle load, road conditions and other factors.
. When a wheel is replaced, the
TPMS will not function and the
low tire pressure warning light
will flash for approximately 1
minute. The light will remain on
after 1 minute. It is recommended
you contact your GT-R certified
NISSAN dealer as soon as possi-
ble for tire replacement and/or
system resetting.
. Replacing tires with those not
originally specified by NISSAN
could affect the proper operation
of the TPMS.
. Do not inject any tire liquid or
aerosol tire sealant into the tires,
as this may cause a malfunction
of the tire pressure sensors.
NOTICE
.The TPMS may not function prop-
erly when the wheels are
equipped with tire chains or the
wheels are buried in snow.
. The TPMS may not function prop-
erly if the TPMS sensor is not
reset and when wheels/tires from

operates to prevent one drive wheel from
slipping by transferring power to a non
slipping drive wheel. The VDC warning
light
will not flash. The VDC
system is automatically reset to on when
the ignition switch is placed in the off
position then back to the on position.
(
“Vehicle Dynamic Control (VDC)
warning light” page 2-34,
“Vehicle
Dynamic Control (VDC) off indicator light”
page 2-33)
The computer has a built-in diagnostic
feature that tests the system each time
you start the engine and move the vehicle
forward or in reverse at a slow speed.
When the self-test occurs, you may hear a
“clunk” noise and/or feel a pulsation in the
brake pedal. This is normal and is not an
indication of a malfunction.
may illuminate.
. If brake related parts such as
brake pads, rotors and calipers
are not standard equipment or
are extremely deteriorated, the
VDC system may not operate
properly and the VDC warning
light
may illuminate.
. If engine control related parts are
not standard equipment or are
extremely deteriorated, the VDC
warning light
may illuminate.
. When driving on extremely in-
clined surfaces such as higher
banked corners, the VDC system
may not operate properly and the
VDC warning light
may illumi-
nate. Do not drive on these types of roads.
. When driving on an unstable sur-
face such as a turntable, ferry,
elevator or ramp, the VDC warn-
ing light
may illuminate. This
is not a malfunction. Restart the
engine after driving onto a stable
surface.
. If wheels or tires other than the
those recommended are used,
the VDC system may not operate
properly and the VDC warning
light
may illuminate.
. The VDC system is not a substi-
tute for winter tires or tire chains
on a snow covered road.
NOTE:
. Always make sure the VDC is ON
before driving the vehicle by check-
ing that the VDC OFF indicator lights
on the meter and the VDC set-up
switch are not illuminated.
The GT-R is a high performance
vehicle and the VDC must be on/
activated to provide proper power-
train operation and intended driva-
bility.Starting and driving
5-55

to change the mile-
age. Push and hold the switch to
increase the number every 600 miles
(1,000 km).
. Set to “—” to set no reminders.
. To reset the accumulated mileage to
zero, go to the RESET screen, then
push the NEXT switch
and confirm
with the ENTER switch.
NOTE:
. To restore the mileage to the origi-
nal figure after resetting, push the
NEXT switch
again.
. When the battery terminal is discon-
nected, the set mileage will be
erased and the settings will return
to their default settings.
Engine oil level:
This can be used to check the pre-start oil
level while the engine is running. Select
SETTING > MAINTENANCE > OIL > ENGINE
OIL > LEVEL.
If the low level reminder appears, check
the level using the engine oil dipstick.
(
“Checking engine oil level” page 8-9)

Transmission oil:
The reminder is displayed when the
customer set mileage is exceeded. Select
SETTING > MAINTENANCE > OIL > T/M OIL
to set or reset the mileage for the
transmission oil change.
NOTE:
The default setting is 37,000 miles
(60,000 km). The maximum mileage
that can be set is 55,500 miles (90,000
km).
Tires:
This reminder appears when the custo-
mer set distance comes for maintaining
tires. You can set or reset the distance for
maintaining tires. (
“Setting (drive
computer)” page 2-20)

Check the coolant level in the pressurized
coolant reservoir. Adjust the level so that
the fluid is between the MAX and MIN
markings. For the coolant, use genuine
NISSAN Long Life coolant or equivalent.
(On delivery of new vehicle, the reservoir
is filled to the MIN level. Be sure to
replenish approximately 3/8 US quart
(0.3 to 0.4 liter) of coolant.)
NOTICE
Do not overfill the coolant. This may
increase the pressure in the cooling
system and cause coolant leaks.
To maximize vehicle performance, the
coolant mixture ratio should be a combi-
nation of 30% coolant antifreeze and 70%
demineralized or distilled water for max-
imum cooling system performance re-
gardless of ambient temperatures.
If ambient temperatures are anticipated
below 5°F (−15°C), make sure a proper
mixture ratio of 50% antifreeze and 50%
demineralized or distilled water mix is
used.Engine and powertrainThe information and specifications in
this section apply only when engaging in performance driving.
.
Check the engine, transmission, differ-
ential and under the vehicle for oil and
coolant leaks.
. Inspect the areas surrounding of the
catalytic converter for heat deteriora-
tion.
. Always perform the transmission
setting. After that, adjust the clutch
clearance so that the clearance is less
than the clearance used for daily
driving. Your GT-R certified NISSAN
dealer has the necessary information
and equipment to set the clutch
clearance to the correct specification.
The clearance used for daily driving
increases clutch heat generated dur-
ing Performance Driving. This leads to
an increase in temperature of the
transmission oil. In addition, a more
direct shifting feel can be obtained by
reducing the clutch clearance for
Performance Driving. The clutch clear-
ance should be reset to the daily
driving specification after Perfor-
mance Driving. It is recommended
you see a GT-R certified NISSAN dealer
for information.
NOTICE
Failure to have the clutch properly
adjusted before performance driving
may cause the transmission oil tem-
perature to increase which may
cause transmission damage.
. Inspect and confirm the clearance
between the exhaust finisher and rear
bumper is more than 0.24 in (6 mm)
(up/down) and more than 0.20 in (5
mm) (left/right).
. Inspect the dust boot of the drive
shaft universal joint for cracks or
damage.Suspension and wheel alignmentThe information and specifications in
this section apply only when engaging
in performance driving.
.Check the steering and suspension
system and other links for loose and/
or damaged parts.
. Measure and adjust the wheel align-
ment. (
“Wheel alignment” page
GTR-10) It is recommended you con-
tact a GT-R certified NISSAN dealer to
adjust the wheel alignment to the
recommended setting for high perfor-

.You can also check the pressure of all
tires on the touch screen display.
Refer to the separate Multi Function
Display Owner’s Manual.
. The tire pressure sensor should be
reset anytime the wheels or tires are
removed or replaced.
. If the tire is removed in order to
replace the tire pressure sensor bat-
tery, it may not be possible to reuse
the removed tire from the wheel. To
replace the tire pressure sensor bat-
tery, it is recommended you contact a
GT-R certified NISSAN dealer.
WARNING
.If the low tire pressure warning
light illuminates while driving,
avoid sudden steering maneu-
vers or abrupt braking, reduce
vehicle speed, pull off the road
to a safe location and stop the
vehicle as soon as possible. Driv-
ing with under-inflated tires may
permanently damage the tires
and increase the likelihood of tire
failure. Serious vehicle damage
could occur and may lead to an
accident and could result in ser-
ious personal injury. Check the tire pressure for all four tires.
Adjust the tire pressure to the
recommended COLD tire pressure
shown on the Tire and Loading
Information label to turn the low
tire pressure warning light off. If
the light still illuminates while
driving after adjusting the tire
pressure, a tire may be flat
(
“Run-flat tires” page 6-4) or
the TPMS may be malfunctioning.
If no tire is flat and all tires are
properly inflated, have the vehicle
checked. It is recommended you
have the vehicle checked by a
GT-R certified NISSAN dealer.
. Although you can continue driv-
ing with a punctured run-flat tire,
remember that vehicle handling
stability is reduced, which could
lead to an accident and personal
injury. Also, driving a long dis-
tance at high speeds may da-
mage the tires.
. Do not drive at speeds above 50
MPH (80 km/h) and do not drive
more than 50 miles (80 km) with a
punctured run-flat tire. The actual
distance the vehicle can be driven
on a flat tire depends on outside
temperature, vehicle load, road conditions and other factors.
. When a wheel is replaced, the
TPMS will not function and the
low tire pressure warning light
will flash for approximately 1
minute. The light will remain on
after 1 minute. It is recommended
you contact your GT-R certified
NISSAN dealer as soon as possi-
ble for tire replacement and/or
system resetting.
. Replacing tires with those not
originally specified by NISSAN
could affect the proper operation
of the TPMS.
. Do not inject any tire liquid or
aerosol tire sealant into the tires,
as this may cause a malfunction
of the tire pressure sensors.
NOTICE
.The TPMS may not function prop-
erly when the wheels are
equipped with tire chains or the
wheels are buried in snow.
. The TPMS may not function prop-
erly if the TPMS sensor is not
reset and when wheels/tires from