engine NISSAN LATIO 2011 Service Repair Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2011, Model line: LATIO, Model: NISSAN LATIO 2011Pages: 3787, PDF Size: 78.35 MB
Page 1270 of 3787
WARNING LAMPSDI-31
< SERVICE INFORMATION >
C
DE
F
G H
I
J
L
M A
B
DI
N
O P
2.CHECK IPDM E/R INPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage between IPDM E/R harness connector and ground.
OK or NG
OK >> Replace IPDM E/R. Refer to PG-28, "Removal and
Installation of IPDM E/R".
NG >> GO TO 3.
3.CHECK OIL PRESSURE SWITCH
1. Turn ignition switch OFF.
2. Disconnect oil pressure switch connector.
3. Check oil pressure switch. Refer to DI-32, "
Component Inspection".
OK or NG
OK >> GO TO 4.
NG >> Replace oil pressure switch.
4.CHECK OIL PRESSURE SWITCH CIRCUIT
1. Disconnect IPDM E/R connector.
2. Check continuity between IPDM E/R harness connector (A) and oil pressure switch harness connector (B).
OK or NG
OK >> Replace IPDM E/R. Refer to PG-28, "Removal and
Installation of IPDM E/R".
NG >> Repair harness or connector.
5.CHECK CAN COMMUNICATION
Select “METER/M&A” on CONSULT-III, and per form self-diagnosis of combination meter.
Self
-diagnostic results content
No malfunction detected>> GO TO 6.
Malfunction detected>> Check applicable parts, and repair or replace as necessary.
6.CHECK COMBINATION METER INPUT SIGNAL
Select “METER/M&A” on CONS ULT-III. Operate ignition switch with “OIL W/L” of “DATA MONITOR” and
check operation status.
OK or NG
OK >> Replace combination meter. Refer to IP-12, "Removal and Installation".
NG >> Replace IPDM E/R. Refer to PG-28, "
Removal and Installation of IPDM E/R".
Te r m i n a l s
ConditionVoltage (Ap-
prox.)
(+)
(–)
IPDM E/R
connector Te r m i n a l
E46 37 Ground Engine stopped 0 V
WKIA5458E
AB
Continuity
Connector Terminal Connector Terminal
E46 37 F32 1 Yes
WKIA5459E
“OIL W/L”
When ignition switch is in ON
position (Engine stopped.) : ON
When engine running : OFF
Revision: May 2010 2011 Versa
Page 1272 of 3787
![NISSAN LATIO 2011 Service Repair Manual WARNING LAMPSDI-33
< SERVICE INFORMATION >
C
DE
F
G H
I
J
L
M A
B
DI
N
O P
Check continuity between oil pressure switch and ground.
Condition Oil pressure [kPa (bar, kg/cm2, psi)]Continuity
Engine sto](/img/5/57357/w960_57357-1271.png "NISSAN LATIO 2011 Service Repair Manual WARNING LAMPSDI-33
< SERVICE INFORMATION >
C
DE
F
G H
I
J
L
M A
B
DI
N
O P
Check continuity between oil pressure switch and ground.
Condition Oil pressure [kPa (bar, kg/cm2, psi)]Continuity
Engine sto")
WARNING LAMPSDI-33
< SERVICE INFORMATION >
C
DE
F
G H
I
J
L
M A
B
DI
N
O P
Check continuity between oil pressure switch and ground.
Condition Oil pressure [kPa (bar, kg/cm2, psi)]Continuity
Engine stopped Less than 29 (0.3, 0.3, 4) Yes
Engine running More than 29 (0.3, 0.3, 4) No
ELF0044D
Revision: May 2010 2011 Versa
Page 1295 of 3787
EC-1
ENGINE
C
DE
F
G H
I
J
K L
M
SECTION EC
A
EC
N
O P
CONTENTS
ENGINE CONTROL SYSTEM
HR16DE
BASIC INSPECTION ....... ............................
15
DIAGNOSIS AND REPAIR WORK FLOW .... ....15
Work Flow ........................................................... ....15
Diagnostic Work Sheet ............................................18
INSPECTION AND ADJUSTMENT ....................20
BASIC INSPECTION .................................................20
BASIC INSPECTION : Spec ial Repair Require-
ment .................................................................... ....
20
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT .................................................... ....
23
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description ................................
23
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement .....
23
IDLE SPEED .......................................................... ....24
IDLE SPEED : Description ........................ ..............24
IDLE SPEED : Special R epair Requirement ...........24
IGNITION TIMING .................................................. ....24
IGNITION TIMING : Description ..............................24
IGNITION TIMING : Special Repair Requirement ....24
VIN REGISTRATION ............................................. ....24
VIN REGISTRATION : Description .........................24
VIN REGISTRATION : Special Repair Require-
ment ........................................................................
25
ACCELERATOR PEDAL RELEASED POSITION
LEARNING ............................................................ ....
25
ACCELERATOR PEDAL RELEASED POSITION
LEARNING : Description .........................................
25
ACCELERATOR PEDAL RELEASED POSITION
LEARNING : Special Repair Requirement ..............
25
THROTTLE VALVE CLOSED POSITION LEARN-
ING ......................................................................... ....
25
THROTTLE VALVE CLOSED POSITION
LEARNING : Description .........................................
25
THROTTLE VALVE CLOSED POSITION
LEARNING : Special Repair Requirement ..............
25
IDLE AIR VOLUME LEARNING ............................ ....25
IDLE AIR VOLUME LEARNING : Description .........25
IDLE AIR VOLUME LEARNI NG : Special Repair
Requirement ........................................................ ....
26
MIXTURE RATIO SELF-LEARNING VALUE
CLEAR ................................................................... ....
27
MIXTURE RATIO SELF-LEARNING VALUE
CLEAR : Description ................................................
27
MIXTURE RATIO SELF-LEARNING VALUE
CLEAR : Special Repair Requirement .....................
27
HOW TO SET SRT CODE ................................29
Description ...............................................................29
SRT Set Driving Pattern ..........................................30
Work Procedure .......................................................32
HOW TO ERASE PERMANENT DTC ..............34
Description ...............................................................34
Work Procedure (Group A) ......................................35
Work Procedure (Group B) ......................................37
FUNCTION DIAGNOSIS ..............................40
ENGINE CONTRO L SYSTEM ..........................40
System Diagram ................................................. ....40
System Description ..................................................41
Component Parts Location ....................................41
Component Description ...........................................45
MULTIPORT FUEL INJECTION SYSTEM .......47
System Diagram .....................................................47
System Description ..................................................47
Component Parts Location ....................................50
Component Description ...........................................54
ELECTRIC IGNITION SYSTEM ........................56
Revision: May 2010 2011 Versa
Page 1299 of 3787
EC-5
C
DE
F
G H
I
J
K L
M
EC A
N
O P
Component Inspection (Fuel filler cap) ...............
..
344
Component Inspection (Drain filter) ......................345
P0460 FUEL LEVEL SENSOR ...................... ..346
Description .......................................................... ..346
DTC Logic .............................................................346
Diagnosis Procedure .............................................346
P0461 FUEL LEVEL SENSOR ........................347
Description .......................................................... ..347
DTC Logic .............................................................347
Component Function Check ..................................347
Diagnosis Procedure .............................................348
P0462, P0463 FUEL LEVEL SENSOR ............349
Description .......................................................... ..349
DTC Logic .............................................................349
Diagnosis Procedure .............................................349
P0500 VSS .......................................................351
Description .......................................................... ..351
DTC Logic .............................................................351
Component Function Check ..................................352
Diagnosis Procedure .............................................352
P0506 ISC SYSTEM .........................................353
Description .......................................................... ..353
DTC Logic .............................................................353
Diagnosis Procedure .............................................353
P0507 ISC SYSTEM .........................................355
Description .......................................................... ..355
DTC Logic .............................................................355
Diagnosis Procedure .............................................355
P0603 ECM POWER SUPPLY .........................357
Description .......................................................... ..357
DTC Logic .............................................................357
Diagnosis Procedure .............................................357
P0605 ECM .......................................................359
Description ............................................................359
DTC Logic .............................................................359
Diagnosis Procedure .............................................360
P0607 ECM .......................................................361
Description ............................................................361
DTC Logic .............................................................361
Diagnosis Procedure .............................................361
P0643 SENSOR POWER SUPPLY .................362
DTC Logic ........................................................... ..362
Wiring Diagram .....................................................363
Diagnosis Procedure .............................................363
P0850 PNP SWITCH ........................................366
Description ............................................................366
DTC Logic .............................................................366
Component Function Check ..................................367
Wiring Diagram .....................................................368
Diagnosis Procedure .............................................368
P1148 CLOSED LOOP CONTROL ................371
DTC Logic ............................................................ ..371
P1217 ENGINE OVER TEMPERATURE ........372
DTC Logic ..............................................................372
Component Function Check ..................................372
Diagnosis Procedure .............................................373
P1225 TP SENSOR .........................................376
Description .............................................................376
DTC Logic ..............................................................376
Diagnosis Procedure .............................................376
Special Repair Requirement ..................................377
P1226 TP SENSOR .........................................378
Description .............................................................378
DTC Logic ..............................................................378
Diagnosis Procedure .............................................378
Special Repair Requirement ..................................379
P1421 COLD START CONTROL ...................380
Description .............................................................380
DTC Logic ..............................................................380
Diagnosis Procedure .............................................380
P1715 INPUT SPEED SENSOR (PRIMARY
SPEED SENSOR) ...........................................
382
Description ........................................................... ..382
DTC Logic ..............................................................382
Diagnosis Procedure .............................................382
P1805 BRAKE SWITCH .................................383
Description .............................................................383
DTC Logic ..............................................................383
Wiring Diagram ......................................................384
Diagnosis Procedure .............................................384
Component Inspection (Stop Lamp Switch) ..........386
P2100, P2103 THROTTLE CONTROL MO-
TOR RELAY ....................................................
387
Description .............................................................387
DTC Logic ..............................................................387
Wiring Diagram ......................................................388
Diagnosis Procedure .............................................388
P2101 ELECTRIC THROTTLE CONTROL
FUNCTION ......................................................
391
Description ........................................................... ..391
DTC Logic ..............................................................391
Wiring Diagram ......................................................392
Diagnosis Procedure .............................................392
Component Inspection ...........................................395
Special Repair Requirement ..................................395
P2118 THROTTLE CONTROL MOTOR .........396
Description .............................................................396
DTC Logic ..............................................................396
Wiring Diagram ......................................................397
Diagnosis Procedure .............................................397
Component Inspection ...........................................398
Special Repair Requirement ..................................399
Revision: May 2010 2011 Versa
Page 1300 of 3787
EC-6
P2119 ELECTRIC THROTTLE CONTROL
ACTUATOR .....................................................
400
Description ........................................................... ..400
DTC Logic ..............................................................400
Diagnosis Procedure .............................................400
Special Repair Requirement ..................................401
P2122, P2123 APP SENSOR ......................... .402
Description ........................................................... ..402
DTC Logic ..............................................................402
Wiring Diagram ......................................................403
Diagnosis Procedure .............................................403
Component Inspection ...........................................405
Special Repair Requirement ..................................405
P2127, P2128 APP SENSOR ......................... .406
Description ........................................................... ..406
DTC Logic ..............................................................406
Wiring Diagram ......................................................407
Diagnosis Procedure .............................................407
Component Inspection ...........................................409
Special Repair Requirement ..................................410
P2135 TP SENSOR ........................................ .411
Description ........................................................... ..411
DTC Logic ..............................................................411
Wiring Diagram ......................................................412
Diagnosis Procedure .............................................412
Component Inspection ...........................................414
Special Repair Requirement ..................................414
P2138 APP SENSOR ..................................... .415
Description ........................................................... ..415
DTC Logic ..............................................................415
Wiring Diagram ......................................................416
Diagnosis Procedure .............................................416
Component Inspection ...........................................419
Special Repair Requirement ..................................419
P2A00 A/F SENSOR 1 ................................... .420
Description ........................................................... ..420
DTC Logic ..............................................................420
Wiring Diagram ......................................................421
Diagnosis Procedure .............................................422
COOLING FAN ................................................425
Description ........................................................... ..425
Component Function Check ..................................425
Wiring Diagram ......................................................426
Diagnosis Procedure .............................................427
Component Inspection ...........................................429
ELECTRICAL LOAD SIGNAL .........................431
Description ........................................................... ..431
Component Function Check ..................................431
Diagnosis Procedure .............................................431
FUEL INJECTOR .............................................433
Description ........................................................... ..433
Component Function Check ..................................433
Wiring Diagram ......................................................434
Diagnosis Procedure ............................................ .434
Component Inspection ..........................................435
FUEL PUMP .....................................................437
Description ........................................................... .437
Component Function Check .................................437
Wiring Diagram .....................................................438
Diagnosis Procedure .............................................438
Component Inspection ..........................................440
IGNITION SIGNAL ............................................442
Description ........................................................... .442
Component Function Check .................................442
Wiring Diagram .....................................................443
Diagnosis Procedure .............................................444
Component Inspection (Ignition Coil with Power
Transistor) ............................................................ .
447
Component Inspection (Condenser-2) ..................448
MALFUNCTION INDICATOR LAMP ................449
Description ........................................................... .449
Component Function Check .................................449
Wiring Diagram .....................................................450
Diagnosis Procedure .............................................451
ON BOARD REFUELING VAPOR RECOV-
ERY (ORVR) .....................................................
453
Description ........................................................... .453
Component Function Check .................................453
Diagnosis Procedure .............................................453
Component Inspection (Refueling EVAP vapor cut
valve) ................................................................... .
456
Component Inspection (Drain filter) ......................458
POSITIVE CRANKCASE VENTILATION .........459
Description ........................................................... .459
Component Inspection ..........................................459
REFRIGERANT PRESSURE SENSOR ...........460
Description ........................................................... .460
Component Function Check .................................460
Wiring Diagram .....................................................461
Diagnosis Procedure .............................................461
ECU DIAGNOSIS ......................................464
ECM ................................................................ ..464
Reference Value .................................................. .464
Wiring Diagram — ENGINE CONTROL SYSTEM
— ..........................................................................
474
Fail Safe ...............................................................475
DTC Inspection Priority Chart .............................477
DTC Index ............................................................478
Test Value and Test Limit .....................................481
SYMPTOM DIAGNOSIS ...........................488
ENGINE CONTROL SYSTEM SYMPTOMS .. ..488
Symptom Table .................................................... .488
NORMAL OPERATING CONDITION ...............492
Revision: May 2010 2011 Versa
Page 1301 of 3787
EC-7
C
DE
F
G H
I
J
K L
M
EC A
N
O P
Description ..........................................................
..
492
PRECAUTION ............................................493
PRECAUTIONS .............................................. ..493
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ..
493
Precaution for Procedure without Cowl Top Cover ..493
On Board Diagnosis (OBD) System of Engine and
A/T .........................................................................
493
General Precautions .............................................494
PREPARATION .........................................497
PREPARATION .............................................. ..497
Special Service Tools .......................................... ..497
Commercial Service Tools ....................................497
ON-VEHICLE MAINTENANCE ..................499
FUEL PRESSURE .......................................... ..499
Inspection ............................................................ ..499
EVAP LEAK CHECK ........................................501
Inspection ............................................................ ..501
SERVICE DATA AND SPECIFICATIONS
(SDS) ......... ................................. ................
503
SERVICE DATA AND SPECIFICATIONS
(SDS) .............................................................. ..
503
Idle Speed ........................................................... ..503
Ignition Timing .......................................................503
Calculated Load Value ..........................................503
Mass Air Flow Sensor ...........................................503
MR18DE
SERVICE INFORMATION .. .......................
504
INDEX FOR DTC ............................................ ..504
U0101-U1001 ...................................................... ..504
P0011-P0075 ........................................................504
P0101-P0128 ........................................................504
P0130-P0183 ........................................................505
P0222-P0420 ........................................................505
P0441-P0463 ........................................................506
P0500-P0643 ........................................................506
P0705-P0734 ........................................................507
P0740-P0840 ........................................................507
P0850-P1574 ........................................................508
P1610-P1615 ........................................................508
P1715-P1805 ........................................................508
P2100-P2A00 ........................................................509
PRECAUTIONS ................................................510
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ..
510
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect ............................... ..
510
Precaution for Procedure without Cowl Top Cover ..511
On Board Diagnosis (OBD) System of Engine and
A/T, CVT ................................................................
511
Precaution .............................................................511
PREPARATION ...............................................515
Special Service Tool ..............................................515
Commercial Service Tool ......................................515
ENGINE CONTROL SYSTEM ........................517
Schematic ............................................................ ..517
Multiport Fuel Injection (MFI) System ....................517
Electronic Ignition (EI) System ..............................520
Fuel Cut Control (at No Load and High Engine
Speed) ...................................................................
520
AIR CONDITIONING CUT CONTROL ............522
Input/Output Signal Chart ......................................522
System Description ................................................522
AUTOMATIC SPEED CONTROL DEVICE
(ASCD) ............................................................
523
System Description ................................................523
Component Description .........................................524
CAN COMMUNICATION .................................525
System Description ................................................525
EVAPORATIVE EMISSION SYSTEM .............526
Description .............................................................526
Component Inspection ...........................................528
How to Detect Fuel Vapor Leakage .......................530
ON BOARD REFUELING VAPOR RECOV-
ERY (ORVR) ....................................................
532
System Description ................................................532
Diagnosis Procedure .............................................532
Component Inspection ...........................................535
POSITIVE CRANKCASE VENTILATION .......538
Description .............................................................538
Component Inspection ...........................................538
NVIS (NISSAN VEHICLE IMMOBILIZER SYS-
TEM-NATS) .....................................................
540
Description .............................................................540
ON BOARD DIAGNOSTIC (OBD) SYSTEM ..541
Introduction ............................................................541
Two Trip Detection Logic .......................................541
Emission-related Diagnostic Information ...............542
Malfunction Indicator Lamp (MIL) ..........................565
OBD System Operation Chart ...............................568
BASIC SERVICE PROCEDURE .....................574
Basic Inspection ....................................................574
Idle Speed and Ignition Timing Check ...................578
Procedure After Replacing ECM ...........................579
VIN Registration ....................................................580
Accelerator Pedal Released Position Learning .....580
Throttle Valve Closed Position Learning ...............580
Revision: May 2010 2011 Versa
Page 1302 of 3787
EC-8
Idle Air Volume Learning .......................................580
Fuel Pressure Check .............................................582
TROUBLE DIAGNOSIS ...................................585
Trouble Diagnosis Introduction ............................ ..585
DTC Inspection Priority Chart ................................590
Fail-Safe Chart ......................................................590
Symptom Matrix Chart ...........................................592
Engine Control Component Parts Location ...........596
Vacuum Hose Drawing ..........................................602
Circuit Diagram .................................................... ..603
ECM Harness Connector Terminal Layout ............605
ECM Terminal and Reference Value ................... ..605
CONSULT-III Function (ENGINE) .........................612
Generic Scan Tool (GST) Function .......................618
CONSULT-III Reference Value in Data Monitor
Mode .................................................................... ..
620
TROUBLE DIAGNOSIS - SPECIFICATION
VALUE .............................................................
624
Description ........................................................... ..624
Testing Condition ...................................................624
Inspection Procedure .............................................624
Diagnosis Procedure .............................................624
TROUBLE DIAGNOSIS FOR INTERMITTENT
INCIDENT ........................................................
632
Description ........................................................... ..632
Diagnosis Procedure .............................................632
POWER SUPPLY AND GROUND CIRCUIT ...633
Wiring Diagram .................................................... ..633
Diagnosis Procedure .............................................634
Ground Inspection .................................................638
DTC U0101 CAN COMMUNICATION LINE ....639
Description ........................................................... ..639
On Board Diagnosis Logic .....................................639
DTC Confirmation Procedure ................................639
Wiring Diagram ......................................................640
Diagnosis Procedure .............................................640
DTC U0140 CAN COMMUNICATION LINE ....641
Description ........................................................... ..641
On Board Diagnosis Logic .....................................641
DTC Confirmation Procedure ................................641
Wiring Diagram ......................................................642
Diagnosis Procedure .............................................642
DTC U1001 CAN COMMUNICATION LINE ....643
Description ........................................................... ..643
On Board Diagnosis Logic .....................................643
DTC Confirmation Procedure ................................643
Wiring Diagram ......................................................644
Diagnosis Procedure .............................................644
DTC P0011 IVT CONTROL .............................645
Description ........................................................... ..645
CONSULT-III Reference Value in Data Monitor
Mode .................................................................... ..
645
On Board Diagnosis Logic .....................................646
DTC Confirmation Procedure ............................... .646
Diagnosis Procedure .............................................647
Component Inspection ..........................................648
Removal and Installation .......................................648
DTC P0031, P0032 A/F SENSOR 1 HEATER ..649
Description ........................................................... .649
CONSULT-III Reference Value in Data Monitor
Mode .................................................................... .
649
On Board Diagnosis Logic ....................................649
DTC Confirmation Procedure ................................649
Wiring Diagram .....................................................650
Diagnosis Procedure .............................................651
Component Inspection ..........................................652
Removal and Installation .......................................653
DTC P0037, P0038 HO2S2 HEATER ............ ..654
Description ........................................................... .654
CONSULT-III Reference Value in Data Monitor
Mode .................................................................... .
654
On Board Diagnosis Logic ....................................654
DTC Confirmation Procedure ................................654
Wiring Diagram .....................................................655
Diagnosis Procedure .............................................656
Component Inspection ..........................................658
Removal and Installation .......................................658
DTC P0075 IVT CONTROL SOLENOID
VALVE ............................................................ ..
659
Component Description ....................................... .659
CONSULT-III Reference Value in Data Monitor
Mode .................................................................... .
659
On Board Diagnosis Logic ....................................659
DTC Confirmation Procedure ................................659
Wiring Diagram .....................................................660
Diagnosis Procedure .............................................661
Component Inspection ..........................................662
Removal and Installation .......................................663
DTC P0101 MAF SENSOR ............................ ..664
Component Description ....................................... .664
CONSULT-III Reference Value in Data Monitor
Mode .................................................................... .
664
On Board Diagnosis Logic ....................................664
DTC Confirmation Procedure ................................664
Overall Function Check .........................................665
Wiring Diagram .....................................................667
Diagnosis Procedure .............................................668
Component Inspection ..........................................670
Removal and Installation .......................................671
DTC P0102, P0103 MAF SENSOR ................ ..672
Component Description ....................................... .672
CONSULT-III Reference Value in Data Monitor
Mode .................................................................... .
672
On Board Diagnosis Logic ....................................672
DTC Confirmation Procedure ................................672
Wiring Diagram .....................................................674
Diagnosis Procedure .............................................675
Component Inspection ..........................................677
Revision: May 2010 2011 Versa
Page 1306 of 3787
EC-12
Description .............................................................889
On Board Diagnosis Logic .....................................889
DTC Confirmation Procedure ................................889
Diagnosis Procedure .............................................889
DTC P0507 ISC SYSTEM ................................891
Description ........................................................... ..891
On Board Diagnosis Logic .....................................891
DTC Confirmation Procedure ................................891
Diagnosis Procedure .............................................891
DTC P050A, P050B, P050E COLD START
CONTROL ........................................................
893
Description ........................................................... ..893
On Board Diagnosis Logic .....................................893
DTC Confirmation Procedure ................................893
Diagnosis Procedure .............................................894
DTC P0605 ECM ..............................................895
Component Description ....................................... ..895
On Board Diagnosis Logic .....................................895
DTC Confirmation Procedure ................................895
Diagnosis Procedure .............................................896
DTC P0607 ECM ..............................................897
Description ........................................................... ..897
On Board Diagnosis Logic .....................................897
DTC Confirmation Procedure ................................897
Diagnosis Procedure .............................................897
DTC P0643 SENSOR POWER SUPPLY ........898
On Board Diagnosis Logic ................................... ..898
DTC Confirmation Procedure ................................898
Wiring Diagram ......................................................899
Diagnosis Procedure .............................................900
DTC P0850 PNP SWITCH ...............................903
Component Description ....................................... ..903
CONSULT-III Reference Value in Data Monitor
Mode .................................................................... ..
903
On Board Diagnosis Logic .....................................903
DTC Confirmation Procedure ................................903
Overall Function Check .........................................904
Wiring Diagram ......................................................905
Diagnosis Procedure .............................................906
DTC P1148 CLOSED LOOP CONTROL .........909
On Board Diagnosis Logic ................................... ..909
DTC P1211 TCS CONTROL UNIT ..................910
Description ........................................................... ..910
On Board Diagnosis Logic .....................................910
DTC Confirmation Procedure ................................910
Diagnosis Procedure .............................................910
DTC P1212 TCS COMMUNICATION LINE .....911
Description ........................................................... ..911
On Board Diagnosis Logic .....................................911
DTC Confirmation Procedure ................................911
Diagnosis Procedure .............................................911
DTC P1217 ENGINE OVER TEMPERATURE ..912
System Description .............................................. .912
CONSULT-III Reference Value in Data Monitor
Mode .................................................................... .
913
On Board Diagnosis Logic ....................................913
Overall Function Check .........................................913
Wiring Diagram .....................................................915
Diagnosis Procedure .............................................916
Main 13 Causes of Overheating ...........................919
Component Inspection ..........................................920
DTC P1225 TP SENSOR ..................................921
Component Description ....................................... .921
On Board Diagnosis Logic ....................................921
DTC Confirmation Procedure ................................921
Diagnosis Procedure .............................................921
Removal and Installation .......................................922
DTC P1226 TP SENSOR ................................ ..923
Component Description ....................................... .923
On Board Diagnosis Logic ....................................923
DTC Confirmation Procedure ................................923
Diagnosis Procedure .............................................923
Removal and Installation .......................................924
DTC P1564 ASCD STEERING SWITCH ........ ..925
Component Description ....................................... .925
CONSULT-III Reference Value in Data Monitor
Mode .................................................................... .
925
On Board Diagnosis Logic ....................................925
DTC Confirmation Procedure ................................926
Wiring Diagram .....................................................927
Diagnosis Procedure .............................................928
Component Inspection ..........................................930
DTC P1572 ASCD BRAKE SWITCH ...............931
Component Description ....................................... .931
CONSULT-III Reference Value in Data Monitor
Mode .................................................................... .
931
On Board Diagnosis Logic ....................................931
DTC Confirmation Procedure ................................932
Wiring Diagram .....................................................933
Diagnosis Procedure .............................................934
Component Inspection ..........................................938
DTC P1574 ASCD VEHICLE SPEED SEN-
SOR ..................................................................
940
Component Description ....................................... .940
On Board Diagnosis Logic ....................................940
DTC Confirmation Procedure ................................940
Diagnosis Procedure .............................................940
DTC P1715 INPUT SPEED SENSOR ..............942
A/T .......................................................................... .942
A/T : Description ...................................................942
A/T : CONSULT-III Reference Value in Data Mon-
itor Mode ...............................................................
942
A/T : On Board Diagnosis Logic ............................942
A/T : Diagnosis Procedure ....................................942
Revision: May 2010 2011 Versa
Page 1308 of 3787
EC-14
Wiring Diagram ....................................................1005
Diagnosis Procedure ...........................................1005
ELECTRICAL LOAD SIGNAL ........................1007
CONSULT-III Reference Value in Data Monitor
Mode ....................................................................
1007
Diagnosis Procedure ...........................................1007
FUEL INJECTOR ............................................1009
Component Description .......................................1009
CONSULT-III Reference Va lue in Data Monitor
Mode ....................................................................
1009
Wiring Diagram ....................................................1010
Diagnosis Procedure ...........................................1011
Component Inspection .........................................1013
Removal and Installation .....................................1013
FUEL PUMP ....................................................1014
Description ...........................................................1014
CONSULT-III Reference Va lue in Data Monitor
Mode ....................................................................
1014
Wiring Diagram ....................................................1015
Diagnosis Procedure ...........................................1016
Component Inspection .........................................1018
Removal and Installation .....................................1018
IGNITION SIGNAL ..........................................1019
Component Description .......................................1019
Wiring Diagram ....................................................1020
Diagnosis Procedure ............................................1023
Component Inspection .........................................1026
Removal and Installation ......................................1027
REFRIGERANT PRESSURE SENSOR .........1028
Component Description .......................................1028
Wiring Diagram ....................................................1029
Diagnosis Procedure ............................................1030
Removal and Installation ......................................1032
MIL AND DATA LINK CONNECTOR .............1033
Wiring Diagram ....................................................1033
SERVICE DATA AND SPECIFICATIONS
(SDS) ..............................................................
1035
Fuel Pressure .......................................................1035
Idle Speed and Ignition Timing ............................1035
Calculated Load Value .........................................1035
Mass Air Flow Sensor ..........................................1035
Intake Air Temperature Se nsor ............................1035
Engine Coolant Temperature Sensor ..................1035
Air Fuel Ratio (A/F) Sensor 1 Heater ...................1036
Heated Oxygen sensor 2 Heater .........................1036
Crankshaft Position Sensor (POS) ......................1036
Camshaft Position Sensor (PHASE) ....................1036
Throttle Control Motor ...... ....................................1036
Fuel Injector .........................................................1036
Fuel Pump ............................................................1036
Revision: May 2010 2011 Versa
Page 1312 of 3787
![NISSAN LATIO 2011 Service Repair Manual EC-18
< BASIC INSPECTION >[HR16DE]
DIAGNOSIS AND REPAIR WORK FLOW
NO-1 >> No request for I/M examination from the custom
er: Before returning the vehicle to the customer,
always erase unnecessary DTC](/img/5/57357/w960_57357-1311.png "NISSAN LATIO 2011 Service Repair Manual EC-18
< BASIC INSPECTION >[HR16DE]
DIAGNOSIS AND REPAIR WORK FLOW
NO-1 >> No request for I/M examination from the custom
er: Before returning the vehicle to the customer,
always erase unnecessary DTC")
EC-18
< BASIC INSPECTION >[HR16DE]
DIAGNOSIS AND REPAIR WORK FLOW
NO-1 >> No request for I/M examination from the custom
er: Before returning the vehicle to the customer,
always erase unnecessary DTC in ECM and TCM (Transmission Control Module). Refer to EC-
29, "Description".
NO-2 >> I/M examination, request ed from the customer: GO TO 13.
13.PREPARE FOR I/M EXAMINATION
1. Set SRT codes. Refer to EC-29, "
Description".
2. Erase permanent DTCs. Refer to EC-34, "
Description".
>> INSPECTION END
Diagnostic Work SheetINFOID:0000000005929745
DESCRIPTION
There are many operating conditions that lead to the malfunction of
engine components. A good grasp of such conditions can make trou-
bleshooting faster and more accurate.
In general, each customer feels differently about an incident. It is
important to fully understand the symptoms or conditions for a cus-
tomer complaint.
Utilize a diagnostic worksheet like the one on the WORKSHEET
SAMPLE in order to organize all the information for troubleshooting.
Some conditions may cause the MIL to come on steady or blink and
DTC to be detected. Examples:
• Vehicle ran out of fuel, which caused the engine to misfire.
• Fuel filler cap was left off or incorrectly screwed on, allowing fuel to evaporate into the atmosphere.
SEF907L
Revision: May 2010 2011 Versa