lock NISSAN MURANO 2013 2.G User Guide

Black plate (29,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SSS1028
Lumbar support (if so equipped):GUID-D73A39BF-43C8-459F-9C24-47B7F579C407The lumbar support feature provides lower back
support to the driver.
Push the front
*1or back*2end of the switch
to adjust the seatback lumbar area.
SSS1172
Front passenger’s seatback switch
SSS1175
Remote walk-in switch
Walk-in function (front passenger seat,
CrossCabriolet models):
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
CAUTION
. When operating the walk-in func-
tion, be sure not to contact any
moving parts to avoid possible in-
juries and/or damages.
. When operating the walk-in func-
tion, be sure that the front passen-
ger seat is not occupied by a
passenger and/or any objects to
avoid possible injuries and/or da-
mages.
. After operating the walk-in function,
be sure to return the seat to the
rearmost position and then tilt up
the seatback until it latches.
This feature makes it easier to get in and out of
the rear seat. Use the following procedure when
getting in and out of the rear seat on the
passenger’s side. If the sun visor is used, close it
to the original position before operating the
walk-in feature.
1. Push the front passenger’s seatback switch to fold down the seatback and unlock the
seat position.
Safety — Seats, seat belts and supplemental restraint system1-7
Condition:

Black plate (30,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
1-8Safety — Seats, seat belts and supplemental restraint system
Alternatively, you can push the remote walk-
in switch located on the instrument panel to
fold down the front passenger’s seatback
and unlock the seat position.
2. Slide the seat forward to the foremost
position manually.
3. Get in or out the vehicle.
4. Return the front passenger seat to the
rearmost position. To slide the front passen-
ger seat, see “Manual seat adjustment”
earlier in this section.
SSS1173
Driver’s seatback release (CrossCabrio-
let models)
GUID-116F27BD-8437-47A9-8270-AD99D91FA75DTo exit the rear seat from the driver’s side, pull
the strap behind the driver’s seat to release the
driver’s seatback. The driver’s seatback will tilt
forward so that you can exit the vehicle.
NOTE:
Pulling the strap behind the driver’s seat
does not slide the driver’s seat forward.
You cannot slide the driver’s seat manu-
ally.
WARNING
Before using the driver’s seatback re-
lease, be sure that the driver’s seat is
not occupied by a driver and/or any
objects to avoid possible injuries and/
or damage.
Condition:

Black plate (33,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SSS0227A
RecliningGUID-1BFE5C97-1FC3-4054-A6B3-17A9466D0C05Pull the reclining strap*Aand position the
seatback at the desired angle. Release the
reclining strap after positioning the seat at the
desired angle.
The reclining feature allows adjustment of the
seatback for occupants of different sizes to help
obtain proper seat belt fit. (See “Precautions on
seat belt usage” later in this section.) The
seatback may also be reclined to allow occu-
pants to rest when the vehicle is parked.
WARNING
. Do not ride in a moving vehicle
when the seatback is reclined. This
can be dangerous. The shoulder belt
will not be against your body. In an
accident, you could be thrown into it
and receive neck or other serious
injuries. You could also slide under
the lap belt and receive serious
internal injuries.
. For the most effective protection
when the vehicle is in motion, the
seat should be upright. Always sit
well back in the seat with both feet
on the floor and adjust the seat belt
properly. See “Precautions on seat
belt usage” later in this section.
. After adjustment, check to be sure
the seat is securely locked.
HEAD RESTRAINTSGUID-5E605952-D804-4293-B401-616CD7C38955
WARNING
Head restraints supplement the other
vehicle safety systems. They may pro-
vide additional protection against injury
in certain rear end collisions. Adjust the
head restraints properly, as specified in
this section. Check the adjustment after
someone else uses the seat. Do not
attach anything to the head restraint
stalks or remove the head restraint. Do
not use the seat if the head restraint
has been removed. If the head restraint
was removed, install and properly ad-
just the head restraint before an occu-
pant uses the seating position. Failure
to follow these instructions can reduce
the effectiveness of the head restraints.
This may increase the risk of serious
injury or death in a collision.
Safety — Seats, seat belts and supplemental restraint system1-11
Condition:

Black plate (34,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
1-12Safety — Seats, seat belts and supplemental restraint system
JVR0140X
The illustration shows the seating positions
equipped with head restraints and headrest.
For Hardtop models, the head restraints and the
headrest are adjustable.
For CrossCabriolet models, the front head
restraints are adjustable and the rear head
restraints are not removable or adjustable.
Indicates the seating position is equipped
with a head restraint.
Indicates the seating position is equipped
with an adjustable headrest (for Hardtop mod-
els) .
SSS0992
ComponentsGUID-D58E33DF-16BC-41B1-B4C5-AA96E133EBC71. Head restraint
2. Adjustment notches
3. Lock knob
4. Stalks
SSS0997
AdjustmentGUID-ACB994E3-70CF-4004-BDD8-BB431714EC1EAdjust the head restraint so the center is level
with the center of your ears.
Condition:

Black plate (35,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SSS0993
To raise the head restraint, pull it up.
SSS0994
To lower, push and hold the lock knob and push
the head restraint down.
SSS0995
RemovalGUID-FC0E7C18-BEC7-4083-8503-66512F55EE99Use the following procedure to remove the
adjustable head restraints.
1. Pull the head restraint up to the highestposition.
2. Push and hold the lock knob.
3. Remove the head restraint from the seat.
4. Store the head restraint properly in a secure place so it is not loose in the vehicle.
5. Reinstall and properly adjust the head
restraint before an occupant uses the
seating position.
Safety — Seats, seat belts and supplemental restraint system1-13
Condition:

Black plate (36,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
1-14Safety — Seats, seat belts and supplemental restraint system
SSS0996
InstallGUID-10B7C451-D81D-4E42-9DB2-2C10EBE1FF751. Align the head restraint stalks with the holesin the seat. Make sure that the head restraint
is facing the correct direction. The stalk with
the adjustment notches
*1must be in-
stalled in the hole with the lock knob
*2.
2. Push and hold the lock knob and push the head restraint down.
3. Properly adjust the head restraint before an occupant uses the seating position.
SSS0508
Front-seat Active Head RestraintGUID-3164FE3F-22C1-4D05-B110-75CFEC562928The Active Head Restraint moves forward
utilizing the force that the seatback receives
from the occupant in a rear-end collision. The
movement of the head restraint helps support
the occupant’s head by reducing its backward
movement and helping absorb some of the
forces that may lead to whiplash-type injuries.
Active Head Restraints are effective for colli-
sions at low to medium speeds in which it is said
that whiplash injury occurs most.
Active Head Restraints operate only in certain
rear-end collisions. After the collision, the head
restraints return to their original position. Adjust the Active Head Restraints properly as
described earlier in this section.
Condition:

Black plate (40,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
1-18Safety — Seats, seat belts and supplemental restraint system
damaged.
PREGNANT WOMENGUID-92E572E7-A7ED-4EC2-8824-E9C667CD8A35NISSAN recommends that pregnant women use
seat belts. The seat belt should be worn snug,
and always position the lap belt as low as
possible around the hips, not the waist. Place
the shoulder belt over your shoulder and across
your chest. Never run the lap/shoulder belt over
your abdominal area. Contact your doctor for
specific recommendations.
INJURED PERSONSGUID-B47CCE32-408A-4E62-B891-7EBBE28DCC23NISSAN recommends that injured persons use
seat belts. Check with your doctor for specific
recommendations.
THREE-POINT TYPE SEAT BELTGUID-F9647E3B-7CCB-4333-9D53-DBFEBA7433EC
WARNING
.Every person who drives or rides in
this vehicle should use a seat belt at
all times.
. Do not ride in a moving vehicle
when the seatback is reclined. This
can be dangerous. The shoulder belt
will not be against your body. In an
accident, you could be thrown into it
and receive neck or other serious injuries. You could also slide under
the lap belt and receive serious
internal injuries.
. For the most effective protection
when the vehicle is in motion, the
seat should be upright. Always sit
well back in the seat with both feet
on the floor and adjust the seat belt
properly.
. Do not allow children to play with
the seat belts. Most seating posi-
tions are equipped with Automatic
Locking Retractor (ALR) mode seat
belts. If the seat belt becomes
wrapped around a child’s neck with
the ALR mode activated, the child
can be seriously injured or killed if
the seat belt retracts and becomes
tight. This can occur even if the
vehicle is parked. Unbuckle the seat
belt to release the child. For the
center of the rear seat, the connec-
tor tongue may also be released.
Release the connector tongue by
inserting a suitable tool (such as a
key) into the connector buckle. If the
seat belt can not be unbuckled or is
already unbuckled, release the child
by cutting the seat belt with a suitable tool (such as a knife or
scissors) to release the seat belt.
Condition:

Black plate (41,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SSS0292
Fastening the seat beltsGUID-4C4C9056-82D7-4B6A-80A4-9DBA4C079A821. Adjust the seat. (See “Seats” earlier in thissection.)
2. Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until
you hear and feel the latch engage.
.The retractor is designed to lockduring a sudden stop or on impact.
A slow pulling motion permits the
belt to move and allows you some
freedom of movement in the seat.
.If the seat belt cannot be pulled from its fully retracted position, firmly pull
the belt and release it. Then
smoothly pull the belt out of the retractor.
SSS0290
3. Position the lap belt portion
low and snug
on the hips as shown.
4. Pull the shoulder belt portion toward the retractor to take up extra slack. Be sure the
shoulder belt is routed over your shoulder
and across your chest.
The front passenger seat and the rear seating
positions three-point seat belts have two modes
of operation:
. Emergency Locking Retractor (ELR)
. Automatic Locking Retractor (ALR)
The Emergency Locking Retractor (ELR) mode
allows the seat belt to extend and retract to
allow the driver and passengers some freedom
Safety — Seats, seat belts and supplemental restraint system1-19
Condition:

Black plate (42,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
1-20Safety — Seats, seat belts and supplemental restraint system
of movement in the seat. The ELR locks the seat
belt when the vehicle slows down rapidly or
during certain impacts.
The Automatic Locking Retractor (ALR) mode
(child restraint mode) locks the seat belt for
child restraint installation.
When ALR mode is activated the seat belt
cannot be extended again until the seat belt
tongue is detached from the buckle and fully
retracted. The seat belt returns to the ELR mode
after the seat belt fully retracts. For additional
information, see “Child restraints” later in this
section.
The ALR mode should be used only for
child restraint installation. During normal
seat belt use by an occupant, the ALR
mode should not be activated. If it is
activated, it may cause uncomfortable seat
belt tension.
WARNING
When fastening the seat belts, be
certain that seatbacks are completely
secured in the latched position. If they
are not completely secured, passengers
may be injured in an accident or sudden
stop.
SSS0326
Unfastening the seat beltsGUID-313FD5EC-9489-4699-B4F1-98B31FED4129To unfasten the seat belt, push the button on the
buckle. The seat belt automatically retracts.
Checking seat belt operationGUID-AED6BCDC-CBDB-4FCF-9DB2-9B060E99627ASeat belt retractors are designed to lock seat
belt movement by two separate methods:
.When the belt is pulled quickly from the
retractor.
. When the vehicle slows down rapidly.
To increase your confidence in the seat belts,
check the operation as follows:
. Grasp the shoulder belt and pull forward
quickly. The retractor should lock and restrict further belt movement.
If the retractor does not lock during this check or
if you have any question about seat belt
operation, see a NISSAN dealer.
Condition:

Black plate (43,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SSS1181
Seat belt guide (front seats, CrossCab-
riolet models)
GUID-3EF9ED5F-135A-43B1-8954-CAD684674E27When the seat belt guide is used with the front
seat, the seat belt can easily be pulled out.
Release the seat belt guide, clip the seat belt
and install the seat belt guide again.
When using the seat belt guide, do not allow it
to twist.
WARNING
When using the seat belt guide, make
sure that the seat belt guide is securely
installed to the seat. Otherwise, theseat belt may slip and result in personal
injury.
CAUTION
.
When entering or exiting the rear
seat, or inserting or retrieving lug-
gage with the seatback folded
down, always release the seat belt
guide. Otherwise, the seat belt
guide may be damaged.
. Do not fold the seat forward or pull
it backward by holding the seat belt
guide in your hand. Doing so may
damage the seat belt guide.
SSS0351A
Shoulder belt height adjustment (Hard-
top models)
GUID-E8DCDEEB-44E6-4A0A-B2D9-EB6DBF18146CThe shoulder belt anchor height should be
adjusted to the position best for you. (See
“Precautions on seat belt usage” earlier in this
section.)
To adjust, pull the adjustment button
*1, and
then move the shoulder belt anchor to the
desired position
*2, so that the belt passes
over the center of the shoulder. The belt should
be away from your face and neck, but not falling
off of your shoulder. Release the adjustment
button to lock the shoulder belt anchor into
position.
Safety — Seats, seat belts and supplemental restraint system1-21
Condition: