ignition NISSAN NOTE 2016 Service Repair Manual

BCS-108
< ECU DIAGNOSIS INFORMATION >[WITHOUT INTELLIGENT KEY SYSTEM]
BCM
20
(G) Ground Keyless tuner signal Input Ignition switch
OFFKey inserted into ignition
key cylinder
0 V
Waiting
Signal receiving
21
(P) Ground Immobilizer one way
communication
(clock) signal Input/
Output While waiting Turn ignition switch ON.
Turn ignition switch ON: Pointer
of tester should move.
23
(GR) Ground Security indicator
output signal
InputSecurity indica-
tor ON
0 V
Blinking (Ignition switch
OFF) 11.3 V
OFF Battery voltage
24
(SB) Ground Audio/dongle link
(serial) signal Input/
Output Ignition switch OFF.
5 V
25
(LG) Ground Immobilizer two way
communication sig-
nal Input/
Output While waiting Turn ignition switch ON. Turn ignition switch ON: Pointer
of tester should move.
26
(O) Ground
THERMO amp. sig-
nal InputPush-button ig-
nition switch ON
and blower fan
switch ON A/C switch OFF
Battery voltage
A/C switch ON 0 V
27
(V) Ground
Air conditioner
switch signal Input A/C switch OFF
Battery voltage
ON 0 V
28
(SB) Ground Blower fan sw signal Input Fan switch OFF
0 V
I, II, III or IIII 7.0 - 8.0 V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
PIIB7728J
PIIB7729J
JPMIA0014GB
PKIB4960J
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS-112
< ECU DIAGNOSIS INFORMATION >[WITHOUT INTELLIGENT KEY SYSTEM]
BCM
36
(LG) Ground Output 1 signal Output
Combination
switchOFF
7.0 - 8.0 V
FR WASHER
1.2 V
FR WIPER LOW
TURN LH
TURN RH
37
(Y) Ground Key sw signal Input Ignition switch Ignition key inserted into
ignition key cylinder
Battery voltage
Ignition key removed from
ignition key cylinder 0 V
38
(O) Ground Ign sw signal
Input Ignition switchOFF or ACC
0 V
ON or START Battery voltage
39
(L) Ground CAN high
Input/
Output ——
40
(P) Ground CAN low Input/
Output ——
41
(G) Ground Door unlock output
(DR) signal OutputFront door lock
actuator LH Actuated to UNLOCK po-
sition
Battery voltage
Other than actuated to
UNLOCK position 0 V
42
(Y) Ground Battery (FUSE) Input Ignition switch OFF
Battery voltage
43
(W) Ground Battery saver output
signal
OutputInterior room lamp battery saver activated
0 V
Interior room lamp battery saver not activat-
ed Battery voltage
44
(GR) Ground Rear defogger relay
output signal InputRear window
defogger switch OFF
Battery voltage
ON 0 – 0.5 V
45
(R) Ground Room lamp output
signal OutputInterior room
lamp or map
lamp OFF
Battery voltage
ON Battery voltage
DOOR 0 – 1 V
48
(L) Ground A/C indicator
Input— —
50
(G) Ground Battery (F/L)
Input Ignition switch OFF Battery voltage
52
(L) Ground Power window pow-
er supply (RAP) sig-
nal Output Ignition switch ON
Battery voltage
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx. )
Sign al

name Input/
Output
+ −
PKIB4960J
PKIB4958J
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
BCM
BCS-113
< ECU DIAGNOSIS INFORMATION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
53
(G) Ground Door unlock output
signal
OutputFront door lock
actuator RH,
rear door lock
actuator RH,
rear door lock
actuator LH and
back door lock
actuator Actuated to UNLOCK po-
sition
Battery voltage
Other than actuated to
UNLOCK position 0 V
54
(SB) Ground Door lock output sig-
nal
OutputAll door lock ac-
tuators Actuated to LOCK posi-
tion
Battery voltage
Other than actuated to
LOCK position 0 V
55
(B) Ground Gnd
Output Ignition switch ON 0 V
56
(LG) Ground Rear wiper auto stop
switch Input Rear wiper OFF (stopped)
0V
ON (activated) Battery voltage
57
(BR) Ground Door sw (RR) signal Input Rear door
switch RHOFF (rear door RH
closed)
7.0 - 8.0 V
ON (rear door RH open) 0 V
58
(W) Ground Door sw (RL) signal Input Rear door
switch LHOFF (rear door LH closed)
7.0 - 8.0 V
ON (rear door LH open) 0 V
59
(SB) Ground Door sw (DR) signal Input Front door
switch LHOFF (front door LH
closed)
7.0 - 8.0 V
ON (front door LH open) 0 V
Terminal No.
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
PKIB4960J
PKIB4960J
PKIB4960J
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS-114
< ECU DIAGNOSIS INFORMATION >[WITHOUT INTELLIGENT KEY SYSTEM]
BCM
1: With variable intermittent wipers
2: Without variable intermittent wipers60
(BG) Ground Door sw (AS) signal Input Front door
switch RHOFF (front door RH
closed)
7.0 - 8.0 V
ON (front door RH open) 0 V
62
(P) Ground Door switch (Back)
signal InputBack door
switch OFF (back door closed)
7.0 - 8.0 V
ON (back door open) 0 V
63
(W) Ground Flasher output
(RIGHT) signal
OutputIgnition switch
ON Turn signal switch OFF
0 V
Turn signal switch RH 6.5 V
(Turn signal lamp turn on: 9 - 16
V)
64
(V) Ground
Flasher output
(LEFT) signal Output
Ignition switch
ON Turn signal switch OFF
0 V
Turn signal switch LH 6.5 V
(Turn signal lamp turn on: 9 - 16 V)
68
(R) Ground Rear wiper motor
output 1
OutputPush-button ig-
nition switch ON Rear wiper stop position
Battery voltage
Any position other than
rear wiper stop position 0V
70
(L) Ground
Cargo lamp output
signal Output Back door Closed (cargo lamp OFF)
Battery voltage
Open (cargo lamp ON) 0 – 1 V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
PKIB4960J
PKIB4960J
PKIC6370E
PKIC6370E
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
BCM
BCS-115
< ECU DIAGNOSIS INFORMATION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
Fail-safeINFOID:0000000012432390
FAIL-SAFE CONTROL BY DTC
BCM performs fail-safe control when any DTC are detected.
FAIL-SAFE CONTROL OF COMBINATION SWIT
CH READING FUNCTION CAUSED BY LOW
POWER SUPPLY VOLTAGE
If voltage of battery power supply lower, BCM maintains combination switch reading to the status when input
voltage is less than approximately 9 V.
NOTE:
When voltage of battery power supply is approximately 9 V or more, combination switch reading function
returns to normal operation.
DTC Inspection Priority ChartINFOID:0000000012432391
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
DTC IndexINFOID:0000000012432392
NOTE: Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni- tion switch OFF → ON again.
• 1 - 39: Displayed if any previous ma lfunction is present when current conditi on is normal. It increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF → ON after returning to the normal condi tion if the malfunction is detected again.
Display contents of CONSULT Fail-safe Cancellation
B2190: NATS ANTENNA AMP Inhibit engine cranking Erase DTC
B2191: DIFFERENCE OF KEY Inhibit engine cranking Erase DTC
B2192: ID DISCORD BCM-ECM Inhibit engine cranking Erase DTC
B2193: CHAIN OF BCM-ECM Inhibit engine cranking Erase DTC
B2195: ANTI SCANNING Inhibit engine cranking Ignition switch ON → OFF
B2196: DONGLE NG Inhibit engine cranking Erase DTC
Priority DTC
1 • U1000: CAN COMM
• U1010: CONTROL UNIT (CAN)
2 • B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
• B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
• B2195: ANTI SCANNING
• B2196: DONGLE NG
3 • C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL
• C1708: [NO DATA] FL
• C1709: [NO DATA] FR
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL
• C1716: [PRESS DATA ERR] FL
• C1717: [PRESS DATA ERR] FR
• C1718: [PRESS DATA ERR] RR
• C1719: [PRESS DATA ERR] RL
• C1729: VHCL SPEED SIG ERR
Revision: August 2015
2016 Versa Note

cardiagn.com

BCS
ADDITIONAL SERVICE WHEN REPLACING BCMBCS-121
< BASIC INSPECTION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
BASIC INSPECTION
ADDITIONAL SERVICE WHEN REPLACING BCM
DescriptionINFOID:0000000012432394
BEFORE REPLACEMENT
When replacing BCM, save or print current vehicle s
pecification with CONSULT configuration before replace-
ment.
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after
replacing BCM.
AFTER REPLACEMENT
CAUTION:
When replacing BCM, always perform “WRITE CONFIGURATION” with CONSULT. Or not doing so,
BCM control function do es not operate normally.
• Complete the procedure of “WRITE CONFIGURATION” in order.
• Configuration is different for each vehicle model. Confirm conf iguration of each vehicle model.
• If you set incorrect “WRITE CONF IGURATION”, incidents might occur.
NOTE:
When replacing BCM, perform the system initialization (NATS) (if equipped).
Work ProcedureINFOID:0000000012432395
1.SAVING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “READ CONFIGURATION” to save or prin t current vehicle specification. Refer to BCS-123, "
Descrip-
tion".
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after
replacing BCM.
>> GO TO 2.
2.REPLACE BCM
Replace BCM. Refer to BCS-137, "
Removal and Installation".
>> GO TO 3.
3.WRITING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “WRITE CONFIGURATION - Config file” or “W RITE CONFIGURATION - Manual selection” to write
vehicle specification. Refer to BCS-123, "
Work Procedure".
>> GO TO 4 (with remote keyless entry system).
>> GO TO 6 (without remote keyless entry system).
4.REGISTER IGNITION KEYS
For initialization and registration of ignition keys, refer to CONSULT Immobilizer mode and follow the on-
screen instructions.
>> GO TO 5.
5.REGISTER KEYFOB ID
For registration of keyfob ID, refer to DLK-257, "
ID Code Entry Procedure".
>> Work End.
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
SHIPPING MODE CANCEL OPERATION
BCS-125
< BASIC INSPECTION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
SHIPPING MODE CANCEL OPERATION
Work ProcedureINFOID:0000000012432399
1.SHIPPING MODE CANCEL OPERATION
1. Turn ignition switch OFF.
2. Press in (turn on) the extended storage switch. Refer to PG-65, "
How To Check".
3. Turn ignition switch ON.
4. Turn ignition switch OFF and wait at least 2 seconds.
>> GO TO 2.
2.SHIPPING MODE CANCEL CHECK
1. Turn ignition switch ON.
2. Check that extended storage warning message is not displayed in combination meter or display.
>> WORK END
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS-126
< BASIC INSPECTION >[WITHOUT INTELLIGENT KEY SYSTEM]
TRANSIT MODE CANCEL OPERATION
TRANSIT MODE CANCEL OPERATION
Work ProcedureINFOID:0000000012432400
1.TRANSIT MODE CANCEL OPERATION
1. Turn ignition switch OFF.
2. Do the following at the same time for 2 seconds:
- Move front wiper switch to HI position (all the way down)
- Move turn signal switch to left position (all the way down)
>> GO TO 2.
2.TRANSIT MODE CANCEL CHECK
1. Turn front wiper switch and turn signal switch OFF.
2. Turn ignition switch ON.
3. Check that turn signal indicators in combination meter do not turn ON.
>> Work End.
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
U1000 CAN COMMBCS-127
< DTC/CIRCUIT DIAGNOSIS > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM
DescriptionINFOID:0000000012432401
Refer to
LAN-7, "CAN COMMUNICATION SYSTEM : System Description".
DTC LogicINFOID:0000000012432402
DTC DETECTION LOGIC
NOTE:
U1000 can be set if a module harness was disconnected and reconnected, perhaps during a repair. Confirm
that there are actual CAN diagnostic symptoms and a present DTC by performing the Self Diagnostic Result
procedure.
Diagnosis ProcedureINFOID:0000000012432403
1. PERFORM SELF DIAGNOSTIC RESULT
1. Turn ignition switch ON and wait for 2 second or more.
2. Check “Self Diagnostic Result” of “BCM” using CONSULT.
Is
“CAN COMM CIRCUIT” displayed?
YES >> Perform CAN Diagnosis as described in DI AGNOSIS section of CONSULT Operation Manual.
NO >> Refer to GI-42, "
Intermittent Incident".
CONSULT Display DTC Detection Condition Possible Cause
CAN COMM CIRCUIT
[U1000] When any listed module cannot communicate
with CAN communication signal continuously for
2 seconds or more with ignition switch ON In CAN communication system, any item (or
items) of the following listed below is malfunc-
tioning.
•Transmission
• Receiving (ECM)
• Receiving (VDC/TCS/ABS)
• Receiving (METER/M&A)
• Receiving (TCM)
• Receiving (IPDM E/R)
Revision: August 2015
2016 Versa Note

cardiagn.com

BCS
POWER SUPPLY AND GROUND CIRCUITBCS-129
< DTC/CIRCUIT DIAGNOSIS > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis ProcedureINFOID:0000000012432406
Regarding Wiring Diagram information, refer to
BCS-117, "Wiring Diagram".
1.CHECK FUSES AND FUSIBLE LINK
Check that the following fuses and fusible link are not blown.
Is the fuse blown?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit.
NO >> GO TO 2.
2.CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connectors.
3. Check voltage between BCM connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK GROUND CIRCUIT
Check continuity between BCM connector and ground.
Is the inspection result normal?
YES >> Inspection End.
NO >> Repair harness or connector.
Terminal No. Signal nameFuses and fusible link No.
37 Battery power supply 8 (10A)
42 12 (10A)
50 G (40A)
11 Ignition switch ACC or ON 18 (10A)
38 Ignition switch ON or START 2 (10A)
BCMGround Ignition switch position
Connector Terminal
—OFF
ACC ON
M18 11
0 V
Battery voltage
Battery voltage
37
Battery voltage
38 0 V0 V
M19 42
Battery voltage Battery voltage
50
BCM GroundContinuity
Connector Terminal
M19 55—Yes
Revision: August 2015 2016 Versa Note

cardiagn.com