USB NISSAN NOTE 2016 Service User Guide

AV
COMPONENT PARTSAV-129
< SYSTEM DESCRIPTION > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts LocationINFOID:0000000012432999
A. Front of headliner B. View with passenger seat removed C. Center of back door
AWNIA3648ZZ
No.Component Function
1. Rod antenna Refer to AV- 1 3 2 , "
Rod Antenna, Antenna Amp., Satellite Antenna and Antenna
Feeder".
2. Antenna base (antenna amp. and satellite
antenna)
3. Rear door speaker RH Refer to AV- 1 3 0 , "
Spe ak ers".
4. Front door speaker RH
5. Front camera Refer to AV- 1 3 2 , "
Front Camera".
6. Front door speaker LH Refer to AV- 1 3 0 , "
Spe ak ers".
7. Side camera Refer to AV- 1 3 2 , "
Side Cameras".
8. Rear door speaker LH Refer to AV- 1 3 0 , "
Spe ak ers".
9. AV control unit Refer to AV- 1 3 0 , "
AV Control Unit".
10. GPS antenna Refer to AV- 1 3 4 , "
GPS Antenna".
11. Steering wheel audio control switches Refer to AV- 1 3 1 , "
Steering Wheel Audio Control Switches".
12. Steering angle sensor Refer to AV- 1 3 2 , "
Steering Angle Sensor".
13. USB interface and AUX in jack Refer to AV- 1 3 1 , "
USB Interface and AUX In Jack".
14. Microphone Refer to AV- 1 3 1 , "
Microphone".
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-130
< SYSTEM DESCRIPTION >[NAVIGATION]
COMPONENT PARTS
*: Around View Monitor is a parking aid/convenience feature. Around View Monitor cannot completely eliminate
blind spots. Around View Monitor may not detect ever y object and does not warn of moving objects. Always
check surroundings before moving vehicle. Around View Monitor is not a substitute for proper backing proce-
dures. Always turn to check what is behind you before backing up.
AV Control UnitINFOID:0000000012433000
Description
• A 5.8-inch QVGA display, an AM/FM electronic tuner radio, CD
drive, audio amplifier, Bluetooth
® module, camera controller and
navigation unit are integrated into the AV control unit.
• The 5.8-inch display is a high resolution monitor that includes touch panel functions.
• Music files stored in iPod
®*/USB memory can be played using the
separate USB interface.
*: iPod® is a registered trademark of Apple, Inc. All rights reserved.
SpeakersINFOID:0000000012433001
FRONT DOOR SPEAKER
• 16.5 cm (6.5 in) speakers are installed in the bottom of the front doors.
• Sound signals are input from the AV control unit to output high, mid and low range sounds.
REAR DOOR SPEAKER
• 16.5 cm (6.5 in) speakers are installed in the bottom of the rear doors.
• Sound signals are input from the AV control unit to output high, midand low range sounds.
15. Around View®* Monitor control unit (if
equipped) Refer to AV- 1 3 1 , "Around View Monitor Control Unit".
16. Rear view camera Refer to AV- 1 3 2 , "
Rear View Camera".
No.
Component Function
ALNIA1524ZZ
JPNIA1454ZZ
JPNIA1454ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
COMPONENT PARTSAV-131
< SYSTEM DESCRIPTION > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
USB Interface and AUX In JackINFOID:0000000012433002
• USB Interface and AUX in jack is installed in the console.
•iPod
® and USB memory can be connected to the AV control unit
through the USB interface.
• An external audio device can be connected to the AV control unit through the AUX in jack.
Steering Wheel Audio Control SwitchesINFOID:0000000012433003
• Steering wheel audio control switches are installed in the steering
wheel.
• Operations for audio and hands-free phone are possible.
• Switch is connected to the AV control unit.
MicrophoneINFOID:0000000012433004
• The microphone is installed in the roof in front of the map lamp
assembly.
• Power is supplied from the AV control unit.
Around View Monitor Control UnitINFOID:0000000012433005
• The around view monitor control unit is installed underneath the passenger seat.
• Vehicle width guide lines, predicted course line, vehicle front guid- ing line and vehicle side line, and vehicle icon are displayed and
combined with camera images.
ALNIA1523ZZ
ALNIA1659ZZ
JPNIA1448ZZ
JSNIA5395ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
SYSTEMAV-135
< SYSTEM DESCRIPTION > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
SYSTEM
System DescriptionINFOID:0000000012433013
SYSTEM DIAGRAM
AUDIO SYSTEM
The audio system consists of the following component:
• AV control unit
• Front door speakers
• Rear door speakers
• Steering wheel audio control switches
• USB interface and AUX in jack
• Antenna base (antenna amp. and satellite antenna)
• Rod antenna
When the audio system is on, AM/FM signals received by the rod antenna are amplified by the antenna amp.
and sent to the AV control unit. The AV control unit then sends audio signals to the front door speakers and
rear door speakers.
Refer to Owner's Manual for audio system operating instructions.
NAVIGATION SYSTEM
Description
• The navigation system can be operated by control panel of the AV control unit and display (touch panel) of
the AV control unit.
• Guide sound during the operation of the navigation system is output from AV control unit to front speakers.
AWNIA4136GB
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
SYSTEMAV-137
< SYSTEM DESCRIPTION > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
• In map-matching, alternative routes to reach the destination will be shown and prioritized, after the road on which the vehicle is cur-
rently driven has been judged and the vehicle mark has been repo-
sitioned.
Alternative routes will be shown in different order of priority, and
the incorrect road can be avoided if there is an error in distance
and/or direction.
Routes are of the same priority if two roads are running in parallel.
Therefore, the vehicle mark may appear on either of them alter-
nately, depending on maneuvering of the steering wheel and con-
figuration of the road.
• Map-matching does not function correctly when a road on which the vehicle is driving is new and not recorded in the map SD-card,
or when road pattern stored in the map data and the actual road
pattern are different due to repair.
The map-matching function may find another road and position the
vehicle mark on it when driving on a road not present in the map.
Then, the vehicle mark may change to it when the correct road is
detected.
• Effective range for comparing the vehicle position and travel direc-
tion calculated by the distance and direction with the road data
read from the map SD-card is limited. Therefore, correction by
map-matching is not possible when there is an excessive gap
between current vehicle position and the position on the map.
GPS (Global Posi tioning System)
GPS (Global Positioning System) is developed for and is controlled
by the US Department of Defense. The system utilizes GPS satel-
lites (NAVSTAR), transmitting out radio waves while flying on an orbit
around the earth at an altitude of approximately 21,000 km (13,049
mile).
The receiver calculates the travel position in three dimensions (lati-
tude/longitude/altitude) according to the time lag of the radio waves
that four or more GPS satellites transmit (three-dimensional position-
ing). The GPS receiver calculates the travel position in two dimen-
sions (latitude/longitude) with the previous altitude data if the GPS
receiver receives only three radio waves (two-dimensional position-
ing). GPS position correction is not performed while stopping the
vehicle.
Accuracy of the GPS will deteriorate under the following conditions:
• In two-dimensional positioning, GPS accuracy will deteriorate when altitude of the vehicle position changes.
• The position of GPS satellite affects GPS detection pr ecision. The position detection may not be precisely
performed.
• The position detection is not performed if GPS receiver does not receive radio waves from GPS satellites. (Inside a tunnel, parking in a building, under an elevated highway etc.) GPS receiver may not receive radio
waves from GPS satellites if any object is placed on the GPS antenna.
NOTE:
• The detection result has an error of approximately 10 m (32.81 ft) even with a high-precision three dimen-
sional positioning.
• There may be cases when the accuracy is lowered and radio waves are stopped intentionally because the GPS satellite signal is controlled by the US trace control center.
USB INTERFACE AND AUX IN JACK
•iPod® or music files in USB memory can be played.
• Sound signals are transmitted from USB interface to the AV control unit and output to each speaker.
•iPod
® is recharged when connected to USB interface.
• Sound can be output from an external device by connecting a device to the AUX in jack.
• AUX sound signals are transmitted to each speaker via AV control unit.
SEL686V
SKIA0613E
SEL526V
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)AV-143
< SYSTEM DESCRIPTION > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
DescriptionINFOID:0000000012433014
The AV control unit on board diagnosis performs the functions listed in the table below:
Perform CONSULT diagnosis if the AV control unit on board diagnosis does not start or the screen does not
display anything.
On Board Diagnosis FunctionINFOID:0000000012433015
METHOD OF STARTING
1. Turn the ignition ON.
2. Turn the audio system OFF.
Mode ItemContent
Ve r s i o n —Version data of the AV control unit is dis-
played.
User Configuration Touch Display Calibration
—Calibration of the touch panel display
can be performed.
Screenshot to USB —A screenshot of the display can be
saved to USB memory.
Time Interval —Destination time interval can be select-
ed.
Radio FM monitor
—
Monitors the dynamic values of the cur-
rent tuner
AM monitor —
SXM monitor —Version data is displayed.
System State Running System Status • SD card slot acces.
• Power Supply
• Speed Signal
• Direction Signal
• Illumination Signal
• GPS Antenna
• GPS tracking
• Satellites visible
• Satellites tracked
• Microphone Current
• Steer. wheel key
• Radio Antenna
• SXM Antenna
• USB Device
• iPod firmware ver.
• BT Status The current system status is displayed.
Sp ea ke r Tes t 4 kH z —This activates a sequence of test tone
outputs to the audio circuits one after the
other for 1 second.
Speaker Test 100Hz
Display-Test
—This provides a test sequence where
test displays (plain colored display: e.g.
white, black, red, blue, green) are shown
one after the other.
The respective color is shown for an in-
dicated period of time (parameter). After
the display test, the design of the display
previously available is stored. While the
screen shows a plain colored display, a
pixel malfunction may be detected.
Self Test • SD Card Access
• BT Module Access
• GPS Antenna
• Radio Antenna
• SXM Antenna A system self test is executed and the
results are stored into the error memory.
Revision: August 2015
2016 Versa Note

cardiagn.com

AV-150
< ECU DIAGNOSIS INFORMATION >[NAVIGATION]
AV CONTROL UNIT
28
(Y) Ground Reverse signal
Input ONSelector lever in R (re-
verse)
Battery voltage
Selector lever in any posi-
tion other than R (reverse) 0 V
30
(Y) Ground AUX jack audio signal LH Input ON Received audio signal
(AUX input)
31
(G) Ground AUX ground
— ON— 0V
32
(L) Ground AUX jack audio signal RH Input ON Received audio signal
(AUX input)
33
(B) Ground Camera ground
— ON — 0 V
34
(L) Ground Camera power supply Output ON Camera image displayed
6.0 V
Except for above 0 V
35
(Shield) —Camera image signal
shield —— —
—
36
1
(Y)
Ground Camera image signal Input ON When camera image is dis-
played
36
2
(G)
37
(BG) Ground Ignition power supply Input ON
—Battery voltage
42
(L) Ground MIC VCC
Output ON—5 V
43
(P) 41
(Shield) Microphone signal
Input ONWhile speaking into micro-
phone.
45
(W) — V BUS signal
— —— —
46
(G) — USB ground
— —— —
Te r m i n a l
(Wire color) Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output Ignition
switch Operation
SKIB3609E
SKIB3609E
SKIB2251J
SKIB3609E
Revision: August 2015
2016 Versa Note

cardiagn.com

AV
AV CONTROL UNITAV-151
< ECU DIAGNOSIS INFORMATION > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
1: Without around view monitor
2: With around view monitor
DTC IndexINFOID:0000000012433019
47
(L) — USB D+ signal
— —— —
48
(R) — USB D
− signal — — — —
49
(Shield) — USB shield
— —— —
50
(B) Ground Antenna amp. ON signal Output ON
AV control unit ON, FM-AM
selected.Battery voltage
51
(B) Ground AM-FM main antenna Input ON AV control unit ON, FM-AM
selected.5.0 V
52
(Shield) —AM-FM main antenna
shield
—— —
—
55
(B) Ground GPS antenna signal Input ON
AV control unit ON, NAV se-
lected.5.0 V
56
(Shield) — GPS antenna shield
— —— —
57
(B) Ground Satellite antenna signal Input ON AV control unit ON, XM se-
lected.
5.0 V
58
(Shield) — Satellite antenna shield — —
——
Te r m i n a l
(Wire color) Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output Ignition
switch Operation
CONSULT Display
Reference Page
U1000: CAN COMM CIRCUIT AV-186, "
AV CONTROL UNIT : DTC Logic"
U1010: CONTROL UNIT (CAN)AV-187, "AV CONTROL UNIT : DTC Logic"
U1200: Cont Unit AV- 1 9 8 , "DTC Logic"
U1217: BLUETOOTH MODULEAV- 1 9 9 , "DTC Logic"
U1229: iPod CERTIFICATIONAV- 2 0 0 , "DTC Logic"
U122F: Digital broadcasting connection errorAV- 2 0 1 , "DTC Logic"
U1244: GPS ANTENNA CONNAV- 2 0 3 , "DTC Logic"
U1258: XM ANTENNA CONNAV- 2 0 4 , "DTC Logic"
U1263: USB OVERCURRENTAV- 2 0 5 , "DTC Logic"
U1264: ANTENNA AMP TERMINALAV- 2 0 6 , "DTC Logic"
U12AA: Configuration ErrorAV- 2 0 7 , "DTC Logic"
U12AC: Display Temperature too High AV- 2 0 8 , "DTC Logic"
U12AD: ECU Temperature too High AV- 2 0 9 , "DTC Logic"
U12AE: Internal Amplifier temperature WarningAV- 2 1 0 , "DTC Logic"
U12AF: CD Mechanism Temperature Warning AV- 2 11 , "DTC Logic"
U12B0: Supply Voltage Goes below 9V > 20sAV- 2 1 2 , "DTC Logic"
U12B1: Supply Voltage Goes High > 16V for 20sAV- 2 1 3 , "DTC Logic"
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
U1263 USBAV-205
< DTC/CIRCUIT DIAGNOSIS > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
U1263 USB
DTC LogicINFOID:0000000012433066
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM SELF DIAGNOSTIC RESULT
1. If there is a device connected to the USB interface, disconnect it.
2. Turn ignition switch ON and wait for 2 seconds or more.
3. Perform Self Diagnostic Result for MULTI AV.
Is DTC U1263 displayed?
YES >> Refer to AV-205, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis ProcedureINFOID:0000000012433067
1.CHECK USB INTERFACE HARNESS
Visually inspect USB interface harness. Refer to AV-245, "
Removal and Installation".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace USB interface harness. Refer to AV-245, "
Removal and Installation".
2.CHECK USB INTERFACE HARNESS
Check USB interface harness. Refer to AV-226, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> Replace AV control unit. Refer to AV-241, "Removal and Installation".
NO >> Replace USB interface harness. Refer to AV-245, "
Removal and Installation".
CONSULT Display DTC Detection Condition Possible Cause
USB OVERCURRENT
[U1263] Overcurrent in USB harness is detected. • Device connected to USB interface.
• Harness between the AV control unit and USB
interface.
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-226
< DTC/CIRCUIT DIAGNOSIS >[NAVIGATION]
USB CONNECTOR
USB CONNECTOR
Diagnosis ProcedureINFOID:0000000012433090
Regarding Wiring Diagram information, refer to
AV-155, "Wiring Diagram".
1.CHECK USB INTERFACE HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect AV control unit connector M76 and USB interface connector M47.
3. Check continuity between AV control unit connector M76 and USB interface connector M47.
4. Check continuity between AV control unit connector M76 and ground.
Is the inspection result normal?
YES >> Replace the USB interface. Refer to AV-245, "Removal and Installation".
NO >> Repair or replace harness or connectors.
AV control unit USB interface
Continuity
Connector TerminalConnector Terminal
M76 45
M47 1
Ye s
46
5
47 3
48 2
49 6
AV control unit
—Continuity
Connector Terminal
M76 45
Ground No
47
Revision: August 2015 2016 Versa Note

cardiagn.com