display NISSAN NOTE 2016 Service Repair Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2016, Model line: NOTE, Model: NISSAN NOTE 2016Pages: 3641, PDF Size: 28.72 MB
Page 719 of 3641
![NISSAN NOTE 2016 Service Repair Manual DLK-30
< SYSTEM DESCRIPTION >[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Fu
nction (BCM - COMMON ITEM)INFOID:0000000012542542
APPLICAT](/img/5/57363/w960_57363-718.png "NISSAN NOTE 2016 Service Repair Manual DLK-30
< SYSTEM DESCRIPTION >[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Fu
nction (BCM - COMMON ITEM)INFOID:0000000012542542
APPLICAT")
DLK-30
< SYSTEM DESCRIPTION >[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Fu
nction (BCM - COMMON ITEM)INFOID:0000000012542542
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
Direct Diagnostic Mode Description
ECU Identification The BCM part number is displayed.
Self Diagnostic Result The BCM self diagnostic results are displayed.
Data Monitor The BCM input/output data is displayed in real time.
Active Test The BCM activates outputs to test components.
Work support The settings for BCM functions can be changed.
Configuration • The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing BCM.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication is displayed.
System Sub System Direct Diagnostic Mode
ECU Identification
Self Diagnostic Result
Data Monitor
Active Test
Work support
Configuration
CAN DIAG SUPPORT MNTR
Door lock
DOOR LOCK ×××
Rear window defogger REAR DEFOGGER ××
Warning chime BUZZER ××
Interior room lamp timer INT LAMP ×××
Exterior lamp HEAD LAMP ×××
Wiper and washer WIPER ×××
Turn signal and hazard warning lamps FLASHER ×××
Air conditioner AIR CONDITIONER ×
Intelligent Key system INTELLIGENT KEY ××××
Combination switch COMB SW ×
BCM BCM× × ×××
Immobilizer IMMU ××××
Interior room lamp battery saver BATTERY SAVER ×××
Vehicle security system THEFT ALM ××
RAP system RETAINED PWR ×
Signal buffer system SIGNAL BUFFER ×
TPMS AIR PRESSURE MONITOR ××××
Panic alarm system PANIC ALARM ×
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 721 of 3641
![NISSAN NOTE 2016 Service Repair Manual DLK-32
< SYSTEM DESCRIPTION >[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
DATA MONITOR
ACTIVE TEST
Monitor Item [Unit]
Main Description
REQ SW -DR [On/Off] ×Indicates condition of door reques](/img/5/57363/w960_57363-720.png "NISSAN NOTE 2016 Service Repair Manual DLK-32
< SYSTEM DESCRIPTION >[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
DATA MONITOR
ACTIVE TEST
Monitor Item [Unit]
Main Description
REQ SW -DR [On/Off] ×Indicates condition of door reques")
DLK-32
< SYSTEM DESCRIPTION >[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
DATA MONITOR
ACTIVE TEST
Monitor Item [Unit]
Main Description
REQ SW -DR [On/Off] ×Indicates condition of door request switch LH.
REQ SW -AS [On/Off] ×Indicates condition of door request switch RH.
REQ SW -BD/TR [On/Off] ×Indicates condition of back door request switch.
PUSH SW [On/Off] Indicates condition of push-button ignition switch.
CLUCH SW [On/Off] ×Indicates condition of clutch interlock switch.
BRAKE SW 1 [On/Off] ×Indicates condition of brake switch.
BRAKE SW 2 [On/Off] Indicates condition of brake switch.
DETE/CANCL SW [On/Off] ×Indicates condition of P (park) position.
SFT PN/N SW [On/Off] ×Indicates condition of P (park) or N (neutral) position.
UNLK SEN -DR [On/Off] ×Indicates condition of door unlock sensor.
PUSH SW -IPDM [On/Off] Indicates condition of push-button ignition switch received from IPDM E/R on
CAN communication line.
IGN RLY1 -F/B [On/Off] Indicates condition of ignition relay 1 received from IPDM E/R on CAN commu-
nication line.
DETE SW -IPDM [On/Off] Indicates condition of detent switch received from TCM on CAN communication
line.
SFT PN -IPDM [On/Off] Indicates condition of P (park) or N (neutral) position from TCM on CAN com-
munication line.
SFT P -MET [On/Off] Indicates condition of P (park) position from TCM on CAN communication line.
SFT N -MET [On/Off] Indicates condition of N (neutral) position from IPDM E/R on CAN communica-
tion line.
ENGINE STATE [Stop/Start/Crank/Run] ×Indicates condition of engine state from ECM on CAN communication line.
VEH SPEED 1 [mph/km/h] ×Indicates condition of ve
hicle speed signal receiv ed from ABS on CAN commu-
nication line.
VEH SPEED 2 [mph/km/h] ×Indicates condition of vehicle speed signal received from combination meter on
CAN communication line.
DOOR STAT -DR [LOCK/READY/UNLK] ×Indicates condition of driver side door status.
DOOR STAT -AS [LOCK/READY/UNLK] ×Indicates condition of passenger side door status.
ID OK FLAG [Set/Reset] Indicates condition of Intelligent Key ID.
PRMT ENG STRT [Set/Reset] Indicates condition of engine start possibility.
RKE OPE COUN1 [0-19] ×When remote keyless entry receiver receives the signal transmitted while oper-
ating on Intelligent Key, the numerical value start changing.
RKE OPE COUN2 [0-19] ×When remote keyless entry receiver receives the signal transmitted while oper-
ating on Intelligent Key, the numerical value start changing.
RKE-LOCK [On/Off] Indicates condition of lock signal from Intelligent Key.
RKE-UNLOCK [On/Off] Indicates condition of unlock signal from Intelligent Key.
RKE-PANIC [On/Off] Indicates condition of panic signal from Intelligent Key.
RKE-MODE CHG [On/Off] Indicates condition of mode change signal from Intelligent Key.
Test Item Description
INSIDE BUZZER This test is able to check combination meter warning chime operation [Take Out/Knob/Key/
Off].
LCD This test is able to check combination meter display in
formation [Off/LK WN/OUTKEY/NO
KY/BATT/INSRT/SFT P/ROTAT/ID NG/B&P I/B&P N].
BATTERY SAVER This test is able to check battery saver operation [On/Off].
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 754 of 3641
![NISSAN NOTE 2016 Service Repair Manual B2621 INSIDE ANTENNADLK-65
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
DTC/CIRCUIT DIAGNOSIS
B2621 INSIDE ANTENNA
DTC LogicINFOID:0000000012429997
DTC DET](/img/5/57363/w960_57363-753.png "NISSAN NOTE 2016 Service Repair Manual B2621 INSIDE ANTENNADLK-65
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
DTC/CIRCUIT DIAGNOSIS
B2621 INSIDE ANTENNA
DTC LogicINFOID:0000000012429997
DTC DET")
B2621 INSIDE ANTENNADLK-65
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
DTC/CIRCUIT DIAGNOSIS
B2621 INSIDE ANTENNA
DTC LogicINFOID:0000000012429997
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “INSIDE ANT DIAG NOSIS” in “Work support”.
3. Perform inside key antenna “INSIDE ANT DIAGNOSIS”.
4. Check BCM for DTC.
Is inside key antenna DTC detected?
YES >> Refer to DLK-65, "Diagnosis Procedure".
NO >> Inside key antenna (instrument center) is OK.
Diagnosis ProcedureINFOID:0000000012429998
Regarding Wiring Diagram information, refer to DLK-46, "Wiring Diagram".
1.CHECK INSIDE KEY ANTENNA INPUT SIGNAL 1
1. Turn ignition switch ON.
2. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-74, "Removal and Installation".
DTCCONSULT display
description DTC detecting condition
Possible cause
B2621 INSIDE ANTENNA 1 An excessive high or low voltage from inside anten-
na (instrument center) is sent to BCM. • Inside key antenna (instrument
center)
• Between BCM Inside key antenna (instrument center)
(+)
(–)Condition Signal
(Reference value)
BCM
Connector Terminal
M98 84
85GroundWhen Intelligent Key is in the an-
tenna detection area.
When Intelligent Key is not in the
antenna detection area.
JMKIA3839GB
JMKIA5951GB
Revision: August 2015
2016 Versa Note
cardiagn.com
Page 756 of 3641
![NISSAN NOTE 2016 Service Repair Manual B2622 INSIDE ANTENNADLK-67
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
B2622 INSIDE ANTENNA
DTC LogicINFOID:0000000012429999
DTC DETECTION LOGIC
DTC CONFI](/img/5/57363/w960_57363-755.png "NISSAN NOTE 2016 Service Repair Manual B2622 INSIDE ANTENNADLK-67
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
B2622 INSIDE ANTENNA
DTC LogicINFOID:0000000012429999
DTC DETECTION LOGIC
DTC CONFI")
B2622 INSIDE ANTENNADLK-67
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
B2622 INSIDE ANTENNA
DTC LogicINFOID:0000000012429999
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “INSIDE ANT DIAG NOSIS” in “Work support”.
3. Perform “INSIDE ANT DIAGNOSIS”.
4. Check BCM for DTC.
Is inside key antenna DTC detected?
YES >> Refer to DLK-67, "Diagnosis Procedure".
NO >> Inside key antenna (console) is OK.
Diagnosis ProcedureINFOID:0000000012430000
Regarding Wiring Diagram information, refer to DLK-46, "Wiring Diagram".
1.CHECK INSIDE KEY ANTENNA INPUT SIGNAL 1
1. Turn ignition switch ON.
2. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-74, "Removal and Installation".
NO >> GO TO 2.
2.CHECK INSIDE KEY ANTENNA CIRCUIT
DTC CONSULT display
description DTC detecting condition
Possible cause
B2622 INSIDE ANTENNA 2 An excessive high or low voltage from inside anten-
na (console) is sent to BCM. • Inside key antenna (console)
• Between BCM Inside key antenna
(console)
(+)
(–) Condition Signal
(Reference value)
BCM
Connector Terminal
M98 86
87GroundWhen Intelligent Key is in the anten-
na detection area.
When Intelligent Key is not in the an-
tenna detection area.
JMKIA3839GB
JMKIA5951GB
Revision: August 2015
2016 Versa Note
cardiagn.com
Page 758 of 3641
![NISSAN NOTE 2016 Service Repair Manual B2623 INSIDE ANTENNADLK-69
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
B2623 INSIDE ANTENNA
DTC LogicINFOID:0000000012430001
DTC DETECTION LOGIC
DTC CONFI](/img/5/57363/w960_57363-757.png "NISSAN NOTE 2016 Service Repair Manual B2623 INSIDE ANTENNADLK-69
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
B2623 INSIDE ANTENNA
DTC LogicINFOID:0000000012430001
DTC DETECTION LOGIC
DTC CONFI")
B2623 INSIDE ANTENNADLK-69
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
B2623 INSIDE ANTENNA
DTC LogicINFOID:0000000012430001
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “INSIDE ANT DIAG NOSIS” in “Work support”.
3. Perform “INSIDE ANT DIAGNOSIS”.
4. Check BCM for DTC.
Is inside key antenna DTC detected?
YES >> Refer to DLK-69, "Diagnosis Procedure".
NO >> Inside key antenna (trunk room) is OK.
Diagnosis ProcedureINFOID:0000000012430002
Regarding Wiring Diagram information, refer to DLK-46, "Wiring Diagram".
1.CHECK INSIDE KEY ANTENNA INPUT SIGNAL 1
1. Turn ignition switch ON.
2. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-74, "Removal and Installation".
NO >> GO TO 2.
2.CHECK INSIDE KEY ANTENNA CIRCUIT
DTC CONSULT display
description DTC detecting condition
Possible cause
B2623 INSIDE ANTENNA 3 An excessive high or low voltage from inside anten-
na (trunk room)
is sent to BCM. • Inside key antenna (trunk room)
• Between BCM Inside key antenna
(trunk room)
(+)
(–) Condition Signal
(Reference value)
BCM
Connector Terminal
M98 88
89GroundWhen Intelligent Key is in the anten-
na detection area.
When Intelligent Key is not in the an-
tenna detection area.
JMKIA3839GB
JMKIA5951GB
Revision: August 2015
2016 Versa Note
cardiagn.com
Page 760 of 3641
![NISSAN NOTE 2016 Service Repair Manual B2626 OUTSIDE ANTENNADLK-71
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
B2626 OUTSIDE ANTENNA
DTC LogicINFOID:0000000012430005
DTC DETECTION LOGIC
DTC CON](/img/5/57363/w960_57363-759.png "NISSAN NOTE 2016 Service Repair Manual B2626 OUTSIDE ANTENNADLK-71
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
B2626 OUTSIDE ANTENNA
DTC LogicINFOID:0000000012430005
DTC DETECTION LOGIC
DTC CON")
B2626 OUTSIDE ANTENNADLK-71
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
B2626 OUTSIDE ANTENNA
DTC LogicINFOID:0000000012430005
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check “Self Diagnostic Result” of “BCM” using CONSULT.
Is outside key antenna DTC detected?
YES >> Refer to DLK-71, "Diagnosis Procedure".
NO >> Outside key antenna (LH) is OK.
Diagnosis ProcedureINFOID:0000000012430006
Regarding Wiring Diagram information, refer to DLK-46, "Wiring Diagram".
1.CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 1
1. Turn ignition switch ON.
2. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-74, "Removal and Installation".
NO >> GO TO 2.
2.CHECK OUTSIDE KEY ANTENNA CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector and outside key antenna (LH) connector.
DTC CONSULT display de-
scription DTC detecting condition
Possible cause
B2626 OUTSIDE ANTENNA
1 An excessive high or low voltage from outside key an-
tenna (LH) is sent to BCM. • Outside key antenna (LH)
• Between BCM and Outside key an-
tenna (LH)
(+)
(–) Condition Signal
(Reference value)
BCM
Connector Terminal
M98 78
79Ground When the driver side
door request switch is
operated with ignition
switch OFF. When Intelligent
Key is in the an-
tenna detection
area. (The dis-
tance between
Intelligent Key
and antenna: 80
cm or less.)
When Intelligent
Key is not in the
antenna detec-
tion area. (The
distance between
Intelligent Key
and antenna: Ap-
prox. 2 m.)
JMKIA5955GB
JMKIA5954GB
Revision: August 2015
2016 Versa Note
cardiagn.com
Page 762 of 3641
![NISSAN NOTE 2016 Service Repair Manual B2627 OUTSIDE ANTENNADLK-73
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
B2627 OUTSIDE ANTENNA
DTC LogicINFOID:0000000012430003
DTC DETECTION LOGIC
DTC CON](/img/5/57363/w960_57363-761.png "NISSAN NOTE 2016 Service Repair Manual B2627 OUTSIDE ANTENNADLK-73
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
B2627 OUTSIDE ANTENNA
DTC LogicINFOID:0000000012430003
DTC DETECTION LOGIC
DTC CON")
B2627 OUTSIDE ANTENNADLK-73
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
B2627 OUTSIDE ANTENNA
DTC LogicINFOID:0000000012430003
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check “Self Diagnostic Result” of “BCM” using CONSULT.
Is DTC detected?
YES >> Refer to DLK-73, "Diagnosis Procedure".
NO >> Outside key antenna (RH) is OK.
Diagnosis ProcedureINFOID:0000000012430004
Regarding Wiring Diagram information, refer to DLK-46, "Wiring Diagram".
1.CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 1
1. Turn ignition switch ON.
2. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-74, "Removal and Installation".
NO >> GO TO 2.
2.CHECK OUTSIDE KEY ANTENNA CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector and outside key antenna (RH) connector.
DTC CONSULT display de-
scription DTC detecting condition
Possible cause
B2627 OUTSIDE ANTENNA
2 An excessive high or low voltage from outside key an-
tenna (RH) is sent to BCM. • Outside key antenna (RH)
• Between BCM and Outside key an-
tenna (RH)
(+)
(–) Condition Signal
(Reference value)
BCM
Connector Terminal
M98 80
81Ground When the passenger
door request switch is
operated with ignition
switch OFF. When Intelligent
Key is in the an-
tenna detection
area. (The dis-
tance between In-
telligent Key and
antenna: 80 cm
or less.)
When Intelligent
Key is not in the
antenna detec-
tion area. (The
distance between
Intelligent Key
and antenna: Ap-
prox. 2 m.)
JMKIA5955GB
JMKIA5954GB
Revision: August 2015
2016 Versa Note
cardiagn.com
Page 764 of 3641
![NISSAN NOTE 2016 Service Repair Manual B2628 OUTSIDE ANTENNADLK-75
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
B2628 OUTSIDE ANTENNA
DTC LogicINFOID:0000000012430007
DTC DETECTION LOGIC
DTC CON](/img/5/57363/w960_57363-763.png "NISSAN NOTE 2016 Service Repair Manual B2628 OUTSIDE ANTENNADLK-75
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
B2628 OUTSIDE ANTENNA
DTC LogicINFOID:0000000012430007
DTC DETECTION LOGIC
DTC CON")
B2628 OUTSIDE ANTENNADLK-75
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
B2628 OUTSIDE ANTENNA
DTC LogicINFOID:0000000012430007
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check “Self Diagnostic Result” of “BCM” using CONSULT.
Is outside key antenna DTC detected?
YES >> Refer to DLK-75, "Diagnosis Procedure".
NO >> Outside key antenna (rear bumper) is OK.
Diagnosis ProcedureINFOID:0000000012430008
Regarding Wiring Diagram information, refer to DLK-46, "Wiring Diagram".
1.CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 1
1. Turn ignition switch ON.
2. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-74, "Removal and Installation".
NO >> GO TO 2.
2.CHECK OUTSIDE KEY ANTENNA CIRCUIT
1. Turn ignition switch OFF.
DTC CONSULT display
description DTC detecting condition
Possible cause
B2628 OUTSIDE ANTENNA
3 An excessive high or low voltage from outside key
antenna (rear bumper) is sent to BCM. • Outside key antenna (rear
bumper)
• Between BCM – Outside key an- tenna (rear bumper)
(+)
(–) Condition Signal
(Reference value)
BCM
Connector Terminal
M98 82
83
Ground When the back
door request
switch is operat-
ed with ignition
switch OFF. When Intelligent
Key is in the an-
tenna detection
area. (The dis-
tance between
Intelligent Key
and antenna: 80
cm or less.)
When Intelligent
Key is not in the
antenna detec-
tion area. (The
distance be-
tween Intelli-
gent Key and
antenna: Ap-
prox. 2 m.)
JMKIA5955GB
JMKIA5954GB
Revision: August 2015
2016 Versa Note
cardiagn.com
Page 841 of 3641
![NISSAN NOTE 2016 Service Repair Manual DLK-152
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR
2. Adjust door striker so that it becomes parallel with front door lock
insertion direction.
3. Tighten door striker bolts](/img/5/57363/w960_57363-840.png "NISSAN NOTE 2016 Service Repair Manual DLK-152
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR
2. Adjust door striker so that it becomes parallel with front door lock
insertion direction.
3. Tighten door striker bolts")
DLK-152
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR
2. Adjust door striker so that it becomes parallel with front door lock
insertion direction.
3. Tighten door striker bolts to specification. Refer to DLK-149, "
Exploded View".
DOOR HINGE
DOOR HINGE : Removal and InstallationINFOID:0000000012430100
REMOVAL
CAUTION:
• Use two people when removing or installing front door due to its heavy weight
• When removing and installing front door assembly, support the door using a suitable tool.
• Use shops cloths to protect surrounding components from damage during removal and installation of front door assembly.
1. Remove front fender. Refer to DLK-147, "
Removal and Installation".
2. Remove front door assembly. Refer to DLK-149, "
DOOR ASSEMBLY : Removal and Installation".
3. Remove front door hinge bolts (body side) and front door hinge.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent to the hinge mating surface.
• After installation, perform the front door adjustment procedure. Refer to DLK-150, "
DOOR ASSEM-
BLY : Adjustment".
• Check door hinge rota ting point for poor lubrication. If neces-
sary, apply a suitable multi-purpose grease.
DOOR CHECK LINK
DOOR CHECK LINK : Re moval and InstallationINFOID:0000000012430101
REMOVAL
1. Remove front door speaker. Refer to AV-54, "Removal and Installation" (BASE AUDIO), AV-114,
"Removal and Installation" (DISPLAY AUDIO) or AV-243, "Removal and Installation" ( N AV I G AT I O N ) .
2. Remove door check link bolt (body side).
3. Remove door check link bolts (door side) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check rear door open/close, lock/ unlock operation.
PIIB2804J
JMKIA8072ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 847 of 3641
![NISSAN NOTE 2016 Service Repair Manual DLK-158
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR
3. Remove rear door hinge bolts and nuts (body side) and rear door hinge.
INSTALLATION
Installation is in the reverse order](/img/5/57363/w960_57363-846.png "NISSAN NOTE 2016 Service Repair Manual DLK-158
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR
3. Remove rear door hinge bolts and nuts (body side) and rear door hinge.
INSTALLATION
Installation is in the reverse order")
DLK-158
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR
3. Remove rear door hinge bolts and nuts (body side) and rear door hinge.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent to
the door hinge mating surface.
• After installation, perform the rear door adjustment procedure. Refer to DLK-156, "
DOOR ASSEMBLY
: Adjustment".
• After adjusting, apply touch-up paint (body color) to the head of door hinge bolts and nuts.
• Check door hinge rota ting point for poor lubrication. If neces-
sary, apply a suitable multi-purpose grease.
DOOR CHECK LINK
DOOR CHECK LINK : Re moval and InstallationINFOID:0000000012430108
REMOVAL
1. Remove rear door speaker. Refer to AV-55, "Removal and Installation" (BASE AUDIO), AV-115, "Removal
and Installation" (DISPLAY AUDIO) or AV-244, "Removal and Installation" (NAVIGATION).
2. Remove door check link bolt (body side).
3. Remove door check link bolts (door side) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check rear door open/close operation.
• Check door check link rotating point for poor lubrication. If
necessary, apply a suitable multi-purpose grease.
JMKIA8072ZZ
JMKIA8074ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com