lock NISSAN NOTE 2016 Service Owner's Manual

BCS
DIAGNOSIS SYSTEM (BCM)BCS-25
< SYSTEM DESCRIPTION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
*: Initial Setting
COMB SW
COMB SW : CONSULT Function (BCM - COMB SW)INFOID:0000000012432323
DATA MONITOR
BCM
BCM : CONSULT Function (BCM - BCM)INFOID:0000000012432324
ECU IDENTIFICATION
The BCM part number is displayed.
SELF DIAGNOSTIC RESULT
Refer to
BCS-50, "DTCIndex".
WORK SUPPORT
CONFIGURATION
Refer to BCS-59, "Description".
AUTO LOCK SET MODE7 5 min
Auto door lock time setting.
MODE6 4 min
MODE5 3 min
MODE4 2 min
MODE3* 1 min
MODE2 30 sec
MODE1 Off
Support Item
Setting Description
Monitor Item [Unit] Description
FR WIPER HI [On/Off]
Indicates condition of wiper operation of combination switch.
FR WIPER LOW [On/Off]
FR WASHER SW [On/Off]
FR WIPER INT [On/Off]
INT VOLUME [1 - 7]
Indicates condition of intermittent wiper operation of combination switch.
RR WIPER ON [On/Off] Indicates condition of rear wiper operation of combination switch.
RR WIPER INT [On/Off]
RR WASHER SW [On/Off]
TURN SIGNAL R [On/Off] Indicates condition of right turn signal op eration of combination switch.
TURN SIGNAL L [On/Off] Indicates condition of left turn signal op eration of combination switch.
TAIL LAMP SW [On/Off] Indicates condition of tail lamp switch operation of combination switch.
HI BEAM SW [On/Off] Indicates condition of Hi beam switch operation of combination switch.
HEAD LAMP SW 1 [On/Off] Indicates condition of head lamp switch 1 operation of combination switch.
HEAD LAMP SW 2 [On/Off] Indicates condition of head lamp switch 2 operation of combination switch.
PASSING SW [On/Off] Indicates condition of passing switch operation of combination switch.
FR FOG SW [On/Off] Indicates condition of front fog lamp switch operation of combination switch.
Support ItemSetting Description
RESET SETTING VALUE Reset Returns BCM to initial value in factory shipment.
Cancel Cancels the reset function.
Revision: August 2015
2016 Versa Note

cardiagn.com

BCS-26
< SYSTEM DESCRIPTION >[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
CAN DIAG SUPPORT MNTR
Refer to
LAN-13, "CAN Diagnostic Support Monitor".
IMMU
IMMU : CONSULT Function (BCM - IMMU)INFOID:0000000012432325
SELF DIAGNOSTIC RESULT
Refer to BCS-50, "DTCIndex".
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
BATTERY SAVER
BATTERY SAVER : CONSULT Func tion (BCM - BATTERY SAVER)INFOID:0000000012432326
DATA MONITOR
Monitor Item [Unit] Description
CONFRM ID ALL [Yet/DONE]
Switches to DONE when an Intelligent Key is registered.
CONFIRM ID4 [Yet/DONE]
CONFIRM ID3 [Yet/DONE]
CONFIRM ID2 [Yet/DONE]
CONFIRM ID1 [Yet/DONE]
TP 4 [Yet/DONE]
DONE indicates the number of Intelligent Key ID which has been registered.
TP 3 [Yet/DONE]
TP 2 [Yet/DONE]
TP 1 [Yet/DONE]
PUSH SW [On/Off]
Indicates condition of push-button ignition switch.
Test Item Description
THEFT IND This test is able to check security indicator operation [On/Off].
Support ItemSetting Description
CONFIRM DONGLE ID —Dongle ID code can be read.
Monitor Item [Unit] Description
REQ SW -DR [On/Off] Indicates condition of door request switch LH.
REQ SW -AS [On/Off] Indicates condition of door request switch RH.
PUSH SW [On/Off] Indicates condition push-button ignition switch.
UNLK SEN -DR [On/Off] Indicates condition of door unlock sensor.
DOOR SW-DR [On/Off] Indicates condition of front door switch LH.
DOOR SW-AS [On/Off] Indicates condition of front door switch RH.
DOOR SW-RR [On/Off] Indicates condition of rear door switch RH.
DOOR SW-RL [On/Off] Indicates condition of rear door switch LH.
DOOR SW-BK [On/Off] Indicates condition of back door switch.
CDL LOCK SW [On/Off] Indicates condition of lock signal from door lock and unlock switch.
CDL UNLOCK SW [On/Off] Indicates condition of unlock signal from door lock and unlock switch.
KEY CYL LK-SW [On/Off] Indicates condition of lock signal from door key cylinder switch.
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
DIAGNOSIS SYSTEM (BCM)BCS-27
< SYSTEM DESCRIPTION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
ACTIVE TEST
WORK SUPPORT
*: Initial setting
THEFT ALM
THEFT ALM : CONSULT Fu
nction (BCM - THEFT)INFOID:0000000012432327
DATA MONITOR
ACTIVE TEST
KEY CYL UN-SW [On/Off] Indicates condition of unlock signal from door key cylinder switch.
RKE-LOCK [On/Off] Indicates condition of lock signal from Intelligent Key.
RKE-UNLOCK [On/Off] Indicates condition of unlock signal from Intelligent Key.
Monitor Item [Unit]
Description
Test itemDescription
BATTERY SAVER This test is able to check battery saver operation [On/Off].
Support ItemSetting Description
BATTERY SAVER SET ON*
Exterior lamp battery saver function ON.
OFF Exterior lamp battery saver function OFF.
ROOM LAMP TIMER SET MODE 3* 10 min.
Sets interior room lamp battery saver timer operating time.
MODE 2 60 min.
MODE 1 15 min.
Monitored Item Description
REQ SW -DR [On/Off] Indicates condition of door request switch LH.
REQ SW -AS [On/Off] Indicates condition of door request switch RH.
REQ SW -BD/TR [On/Off] Indicates condition of back door request switch.
PUSH SW [On/Off] Indicates condition of push-button ignition switch.
UNLK SEN -DR [On/Off] Indicates condition of door unlock sensor.
DOOR SW-DR [On/Off] Indicates condition of front door switch LH.
DOOR SW-AS [On/Off] Indicates condition of front door switch RH.
DOOR SW-RR [On/Off] Indicates condition of rear door switch RH.
DOOR SW-RL [On/Off] Indicates condition of rear door switch LH.
DOOR SW-BK [On/Off] Indicates condition of back door switch.
CDL LOCK SW [On/Off] Indicates condition of lock signal from door lock and unlock switch.
CDL UNLOCK SW [On/Off] Indicates condition of unlock signal from door lock and unlock switch.
KEY CYL LK-SW [On/Off] Indicates condition of lo ck signal from door key cylinder switch.
KEY CYL UN-SW [On/Off] Indicates condition of unlock signal from door key cylinder switch.
RKE-LOCK [On/Off] Indicates condition of lock signal from Intelligent Key.
RKE-UNLOCK [On/Off] Indicates condition of unlock signal from Intelligent Key.
Test Item Description
VEHICLE SECURITY HORN This test is able to check vehicle security horn operation [On].
FLASHER This test is able to check turn signal lamp operation [LH/RH/Off].
THEFT IND This test is able to check security indicator lamp operation [On/Off].
HEAD LAMP(HI) This test is able to check vehicle security lamp operation [On].
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS-30
< ECU DIAGNOSIS INFORMATION >[WITH INTELLIGENT KEY SYSTEM]
BCM
ECU DIAGNOSIS INFORMATION
BCM
Reference ValueINFOID:0000000012432332
NOTE:
The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions. Refer to the Signal Tech
II User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
• Check Intelligent Key relative signal strength
• Confirm vehicle Intelligent Key antenna signal strength
VALUES ON THE DIAGNOSIS TOOL
Monitor Item
Condition Value/Status
AIR COND SW A/C switch OFF
Off
A/C switch ON On
AIR PRESS FL Front left tire air pressure value
kPa, kg/cm
2, psi
AIR PRESS FR Front right tire air pressure value
kPa, kg/cm
2, psi
AIR PRESS RL Rear left tire air pressure value
kPa, kg/cm
2, psi
AIR PRESS RR Rear right tire air pressure value
kPa, kg/cm
2, psi
BRAKE SW 1 When the brake pedal is released
On
When the brake pedal is depressed Off
BRAKE SW2 Brake pedal released
Off
Brake pedal depressed On
BUZZER Buzzer in combination meter OFF
Off
Buzzer in combination meter ON On
CDL LOCK SW Door lock/unlock switch does not operate
Off
Press door lock/unlock switch to the LOCK side On
CDL UNLOCK SW Door lock/unlock switch does not operate
Off
Press door lock/unlock switch to the UNLOCK side On
CLUCH SW Clutch pedal depressed
On
Clutch pedal released Off
CONFRM ID ALL The key ID does not match any key ID registered to BCM. Yet
The key ID matches any key ID registered to BCM.
DONE
CONFIRM ID4 The key ID does not match the fourth key ID registered to BCM. Yet
The key ID matches the fourth key ID registered to BCM.
DONE
CONFIRM ID3 The key ID does not match the third key ID registered to BCM. Yet
The key ID matches the third key ID registered to BCM.
DONE
CONFIRM ID2 The key ID does not match the second key ID registered to BCM. Yet
The key ID matches the second key ID registered to BCM. DONE
CONFIRM ID1 The key ID does not match the first key ID registered to BCM. Yet
The key ID matches the first key ID registered to BCM.
DONE
DETE SW -IPDM When selector lever is in P position
Off
When selector lever is in any position other than P On
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
BCM
BCS-31
< ECU DIAGNOSIS INFORMATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
DETE/CANCL SW
When selector lever is in P position Off
When selector lever is in any position other than P
On
DOOR STAT-AS Passenger door LOCK status
LOCK
Passenger door UNLOCK status UNLK
Wait with selective UNLOCK operation (5 seconds) READY
DOOR STAT-DR Driver door LOCK status
LOCK
Driver door UNLOCK status UNLK
Wait with selective UNLOCK operation (5 seconds) READY
DOOR SW-AS Front door RH closed
Off
Front door RH opened On
DOOR SW-BK Back door closed
Off
Back door opened On
DOOR SW-DR Front door LH closed
Off
Front door LH opened On
DOOR SW-RL Rear door LH closed
Off
Rear door LH opened On
DOOR SW-RR Rear door RH closed
Off
Rear door RH opened On
ENGINE STATE Engine stopped
Stop
While the engine stalls Stall
At engine cranking Crank
Engine running Run
FAN O N SIG Blower motor fan switch OFF
Off
Blower motor fan switch ON On
FR FOG SW Front fog lamp switch OFF
Off
Front fog lamp switch ON On
FR WASHER SW Front washer switch OFF
Off
Front washer switch ON On
FR WIPER LOW Front wiper switch OFF
Off
Front wiper switch LO On
FR WIPER HI Front wiper switch OFF
Off
Front wiper switch HI On
FR WIPER INT Front wiper switch OFF
Off
Front wiper switch INT On
FR WIPER STOP Any position other than front wiper stop position
Off
Front wiper stop position On
HAZARD SW When hazard switch is not pressed
Off
When hazard switch is pressed On
HEAD LAMP SW 1 Headlamp switch OFF
Off
Headlamp switch 1st On
HEAD LAMP SW 2 Headlamp switch OFF
Off
Headlamp switch 1st On
HI BEAM SW High beam switch OFF
Off
High beam switch HI On
Monitor Item
Condition Value/Status
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS-32
< ECU DIAGNOSIS INFORMATION >[WITH INTELLIGENT KEY SYSTEM]
BCM
ID OK FLAGIgnition switch ACC or ON Reset
Ignition switch OFF
Set
ID REGST FL1 ID registration of front left tire incomplete
YET
ID registration of front left tire complete DONE
ID REGST FR1 ID registration of front right tire incomplete
YET
ID registration of front right tire complete DONE
ID REGST RL1 ID registration of rear left tire incomplete
YET
ID registration of rear left tire complete DONE
ID REGST RR1 ID registration of rear
right tire incomplete YET
ID registration of rear right tire complete DONE
IGN RLY1 F/B Ignition switch OFF or ACC
Off
Ignition switch ON On
INT VOLUME Wiper intermittent dial is in a dial position 1 - 7 1 - 7
KEY CYL LK-SW Door key cylinder LOCK position
On
Door key cylinder other than LOCK position Off
KEY CYL UN-SW Door key cylinder UNLOCK position
On
Door key cylinder other than UNLOCK position Off
PASSING SW Other than lighting switch PASS
Off
Lighting switch PASS On
PRMT ENG STRT When the engine start is prohibited
Reset
When the engine start is permitted Set
PUSH SW Return ignition switch to LOCK position
Off
Press ignition switch On
PUSH SW-IPDM When engine switch (push switch) is not pressed
Off
When engine switch (push switch) is pressed On
REAR DEF SW Rear window defogger switch OFF
Off
Rear window defogger switch ON On
REQ SW -AS When passenger door request switch is not pressed
Off
When passenger door request switch is pressed On
REQ SW -BD/TR When back door request switch is not pressed
Off
When back door request switch is pressed On
REQ SW -DR When driver door request switch is not pressed
Off
When driver door request switch is pressed On
RKE-LOCK When LOCK button of Intelligent Key is not pressed
Off
When LOCK button of Intelligent Key is pressed On
RKE-MODE CHG When LOCK/UNLOCK button of Intelligent Key is not pressed and
held simultaneously
Off
When LOCK/UNLOCK button of Intelligent Key is pressed and held
simultaneously On
RKE OPE COUN1 Operation frequency of Intelligent Key 0-19
RKE OPE COUN2 Operation frequency of Intelligent Key 0-19
RKE-PANIC When PANIC button of Intelligent Key is not pressed
Off
When PANIC button of Intelligent Key is pressed On
RKE-UNLOCK When UNLOCK button of Intelligent Key is not pressed
Off
When UNLOCK button of Intelligent Key is pressed On
Monitor Item
Condition Value/Status
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
BCM
BCS-33
< ECU DIAGNOSIS INFORMATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
RR WASHER SW
Rear washer switch OFF Off
Rear washer switch ON
On
RR WIPER INT Rear wiper switch OFF
Off
Rear wiper switch INT On
RR WIPER ON Rear wiper switch OFF
Off
Rear wiper switch ON On
RR WIPER STOP Any position other than rear wiper stop position
Off
Rear wiper stop position On
SFT N-MET When selector lever is in any position other than N
Off
When selector lever is in N position On
SFT P-MET When selector lever is in any position other than P
Off
When selector lever is in P position On
SFT PN -IPDM When selector lever is in any position other than P or N
Off
When selector lever is in P or N position On
SFT PN/N SW When selector lever is in any position other than P or N
Off
When selector lever is in P or N position On
TAIL LAMP SW Other than lighting switch 1ST and 2ND
Off
Lighting switch 1ST or 2ND On
TP 4 The ID of fourth key is not registered to BCM
Yet
The ID of fourth key is registered to BCM DONE
TP 3 The ID of third key is not registered to BCM
Yet
The ID of third key is registered to BCM DONE
TP 2 The ID of second key is not registered to BCM
Yet
The ID of second key is registered to BCM DONE
TP 1 The ID of first key is not registered to BCM
Yet
The ID of first key is registered to BCM DONE
TURN SIGNAL L Turn signal switch OFF
Off
Turn signal switch LH On
TURN SIGNAL R Turn signal switch OFF
Off
Turn signal switch RH On
UNLK SEN-DR Driver door UNLOCK status
Off
Driver door LOCK status On
VEH SPEED 1 While driving, equivalent to speedometer reading mph, km/h
VEH SPEED 2 While driving, equivalent to speedometer reading mph, km/h
WARNING LAMP Low tire pressure warning lamp in combination meter OFF Off
Low tire pressure warning lamp in combination meter ON
On
Monitor Item
Condition Value/Status
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
BCM
BCS-35
< ECU DIAGNOSIS INFORMATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N3
(Y) Ground INPUT 4 signal Input Combination
switchOFF
0 V
TURN LH
1.0 V
PASSING
HEADLAMP 2
FR FOG
4
(L) Ground INPUT 3 signal Input Combination
switchOFF
0 V
FR WIPER LO
1.0 V
FR WIPER INT
(any intermittent position)
5
(G) Ground INPUT 2 signal Input Combination
switchOFF
0 V
FR WASHER
1.0 V
RR WASHER
Wiper intermittent dial 1
Wiper intermittent dial 5
Wiper intermittent dial 6
RR WIPER ON
6
(R) Ground INPUT 1 signal Input Combination
switchOFF
0 V
FR WIPER HI
1.0 V
Wiper intermittent dial 1
Wiper intermittent dial 2
Wiper intermittent dial 3
Wiper intermittent dial 6
Wiper intermittent dial 7
RR WIPER INT
7
(W) Ground
Key cylinder unlock
sw signal Input
Key cylinder
switch N position
7.0 - 8.0 V
UNLOCK position 0 V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
PKIB4958J
PKIB4958J
PKIB4958J
PKIB4958J
PKIB4960J
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS-36
< ECU DIAGNOSIS INFORMATION >[WITH INTELLIGENT KEY SYSTEM]
BCM
8
(GR) Ground Key cylinder lock sw
signal
InputKey cylinder
switch N position
7.0 - 8.0 V
LOCK position 0 V
9
(LG) Ground Stop lamp switch 1 Input Stop lamp
switchOFF (Brake pedal
released)
0 V
ON (Brake pedal
depressed) Battery voltage
12
(GR) Ground
Central door lock sw
signal Input
Door lock and
unlock switch NEUTRAL position
1.0 - 1.5 V
LOCK position 0 V
13
(BR) Ground
Central door unlock
sw signal Input
Door lock and
unlock switch NEUTRAL position
1.0 - 1.5 V
UNLOCK position 0 V
15
(G) Ground Rear defogger
switch signal
InputRear window
defogger switch Not pressed
1.0 - 1.5 V
Pressed 0 V
18
(V) Ground
Keyless tuner
ground Input Push-button ignition switch ON
0 V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
PKIB4960J
JPMIA0012GB
JPMIA0012GB
JPMIA0012GB
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
BCM
BCS-37
< ECU DIAGNOSIS INFORMATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N19
(LG) Ground
Keyless tuner power
supply OutputPush-button ignition switch OFF
Push-button ignition switch ACC or ON
5 V
20
(G) Ground Keyless tuner signal Input Push-button ig-
nition switch
OFFWaiting
When operating either
button on Intelligent Key
21
(P) Ground Immobilizer one way
communication
(CLOCK) signal Input/
Output Intelligent Key
battery is re-
moved Brake pedal depressed
NOTE:
Waveform varies each
time when brake pedal is
depressed
Brake pedal released
Battery voltage
22
(W) Ground Keyless tuner RSSI
signal
InputPush-button ig-
nition switch
OFF Waiting
When pressing and hold-
ing either button on Intelli-
gent Key
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
JMKIA3838GB
JMKIA3838GB
JMKIA3841GB
JMKIA6232JP
JMKIA5952GB
JMKIA5953GB
Revision: August 2015 2016 Versa Note

cardiagn.com