phone NISSAN NOTE 2016 Service Owner's Manual

AV-78
< ECU DIAGNOSIS INFORMATION >[DISPLAY AUDIO]
AUDIO UNIT
37
(P) 39
(Shield) Microphone signal
Input ONWhile speaking into micro-
phone.
38
(L) Ground MIC VCC
Output ON—5 V
44
(B) Ground Camera detection
— ON— 0 V
46
(B) Ground EQ02 Ground
— ON— 0 V
48
(B/W) Ground EQ04 Ground
— ON— 0 V
50
(Y) Ground Reverse signal
Input ONSelector lever in R (re-
verse)
Battery voltage
Selector lever in any posi-
tion other than R (reverse) 0 V
53
(B) — USB ground
— —— —
55
(G) — USB D+ signal
— —— —
56
(W) — USB D
− signal — — — —
57
(R) — V BUS signal
— —— —
58
(Shield) — USB shield
— —— —
60
(G) Ground AUX jack audio signal LH Input ON Received audio signal
(AUX input)
61
(L) Ground AUX jack audio signal RH Input ON Received audio signal
(AUX input)
62
(Y) Ground AUX ground
— ON— 0V
67
(B) Ground Antenna amp. ON signal Output ON Audio unit ON, FM-AM se-
lected.
Battery voltage
68
(B) Ground AM/FM antenna signal Input ON
Audio unit ON, FM-AM se-
lected.5.0 V
Te r m i n a l
(Wire color) Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output Ignition
switch Operation
SKIB3609E
SKIB3609E
SKIB3609E
Revision: August 2015
2016 Versa Note

cardiagn.com

AV-102
< DTC/CIRCUIT DIAGNOSIS >[DISPLAY AUDIO]
MICROPHONE SIGNAL CIRCUIT
MICROPHONE SIGNAL CIRCUIT
Diagnosis ProcedureINFOID:0000000012432971
Regarding Wiring Diagram information, refer to
AV-80, "Wiring Diagram".
1.CHECK HARNESS BETWEEN AUDIO UNIT AND MICROPHONE
1. Turn ignition switch OFF.
2. Disconnect audio unit connector M40 and microphone connector R15.
3. Check continuity between audio unit connector M40 and microphone connector R15.
4. Check continuity between audio unit connector M40 and ground.
Are continuity results as specified?
YES >> GO TO 2.
NO >> Repair harness or connectors.
2.CHECK MICROPHONE POWER SUPPLY
1. Connect audio unit connector M40 and microphone connector R15.
2. Turn ignition switch ON.
3. Check voltage between microphone connector R15 and ground.
Is the voltage reading as specified?
YES >> GO TO 3.
NO >> Replace audio unit. Refer to AV-113, "
Removal and Installation".
3.CHECK MICROPHONE SIGNAL
Check signal between terminals of audio unit connector M40.
Audio unit Microphone
Continuity
Connector TerminalConnector Terminal
M40 37
R15 1
Ye s
38 4
39 2
Audio unit
Ground Continuity
Connector Terminal
M40 37
—N o
38
Microphone Ground
Vol tag e
(Approx.)
(+)
(-)
Connector Terminal
R15 4— 5V
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
MICROPHONE SIGNAL CIRCUITAV-103
< DTC/CIRCUIT DIAGNOSIS > [DISPLAY AUDIO]
C
D
E
F
G H
I
J
K L
M B A
O P
Were voltage readings as specified?
YES >> Replace audio unit. Refer to AV-113, "Removal and Installation".
NO >> Replace microphone. Refer to AV-122, "
Removal and Installation".
Audio unit connector M40
ConditionReference value
(+) (-)
Terminal Terminal
37 39Speak into microphone.
SKIB3609E
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
AUDIO SYSTEMAV-109
< SYMPTOM DIAGNOSIS > [DISPLAY AUDIO]
C
D
E
F
G H
I
J
K L
M B A
O P
RELATED TO HANDS-FREE PHONE
• Before performing diagnosis, confirm that the cellular phone being used by the customer is compatible with the vehicle.
• It is possible that a malfunction is occurring due to a version change of the phone even thoug\
h the phone is a compatible type. This can be confirmed by changing the cellular phone to another compatible type, and
check that it operates normally. It is important to determine whether the c ause of the malfunction is the vehi-
cle or the cellular phone.
Check Compatibility
1. Make sure the customer’s Bluetooth® related concern is understood.
2. Verify the customer’s concern. NOTE:
The customer’s phone may be required, depending upon their concern.
3. Write down the customer’s phone brand, model and service provider. NOTE:
It is necessary to know the service provider. On occasion, a given phone may be on the approved list with
one provider, but may not be on the approved list with other providers.
4. Go to “www.nissanusa.com/bluetooth/”.
a. Using the website’s search engine, find out if the customer’s phone is on the approved list.
b. If the customer’s phone is NOT on the approved list: Stop diagnosis here. The customer needs to obtain a Bluetooth
® phone that is on the approved list before
any further action.
c. If the feature related to the customer’s concern shows as “N” (not compatible):
Stop diagnosis here. If the customer still wants the feature to function, they will need to get an approved
phone showing the feature as “Y” (compatible) in the “Basic Features”.
d. If the feature related to the customer ’s concern shows as “Y” (compatible):
Perform diagnosis as per the following table.
No radio reception or poor reception. • Other audio sounds are normal.
• Any radio station cannot be received or
poor reception is caused even after mov-
ing to a service area with good reception
(e.g. a place with clear view and no ob-
stacles generating external noises). • Antenna amp. ON signal circuit malfunc-
tion.
Refer to AV- 7 6 , "Reference Value".
• Poor connector connection of antenna or antenna feeder.
Refer to AV- 1 2 4 , "
Feeder Layout".
No satellite radio reception. Satellite radio antenna malfunction. • Poor continuity in antenna feeder.
• Poor connector connection of antenna or
antenna feeder.
• Loose satellite radio antenna mounting nut.
Refer to AV- 1 2 4 , "
Feeder Layout".
Buzz/rattle sound from speaker The majority of buzz/rattle sounds are not
indicative of an issue with the speaker, usu-
ally something nearby the speaker is caus-
ing the buzz/rattle.Refer to "SQUEAK AND RATTLE TROU-
BLE DIAGNOSIS" in the appropriate interi-
or trim section.
Symptoms
Check itemsProbable malfunction location
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-110
< SYMPTOM DIAGNOSIS >[DISPLAY AUDIO]
AUDIO SYSTEM
RELATED TO REAR VIEW CAMERA
Symptoms
Check itemsProbable malfunction location
Does not recognize cellular phone connec-
tion (no connection is displayed on the dis-
play at the guide). Repeat the registration of cellular phone.
Malfunction in audio unit.
Refer to AV- 7 1 , "
On Board Diagnosis Func-
tion".
Hands-free phone cannot be established. • Hands-free phone operation can be
made, but the communication cannot be
established.
• Hands-free phone operation can be per-
formed, however, voice between each
other cannot be heard during the conver-
sation.
The other party’s voice cannot be heard by
hands-free phone. Check the “microphone speaker” in Inspec-
tion & Adjustment Mode if sound is heard.
Originating sound is not heard by the other
party with hands-free phone communica-
tion. Sound operation function is normal.
Sound operation function does not work.
Microphone signal circuit malfunction.
Refer to
AV- 1 0 2 , "
Diagnosis Procedure".
The system cannot be operated. Steering switch’s , , and
switch works, but does not work.
Steering switch malfunction.
Replace steering switch. Refer to
AV- 1 2 1 ,
"Removal and Installation".
Steering switch’s , , , and switches do not work. Steering switch signal circuit malfunction.
Refer to
AV- 1 0 4 , "
Diagnosis Procedure".
All steering switches do not work. Steering switch ground circuit malfunction.
Refer to
AV- 1 0 4 , "
Diagnosis Procedure".
Symptoms Check itemsProbable malfunction location
Rear view camera is inoperative. Reverse signal circuit malfunction.
Reverse signal circuit malfunction between
transmission range switch (with CVT) or
park/neutral position
(PNP) switch (back-
up) (with M/T) and audio unit.
Refer to AV- 1 0 0 , "
Diagnosis Procedure".
Camera image signal circuit malfunction. Camera image signal circuit malfunction
between rear view camera and audio unit.
Refer to AV- 1 0 0 , "
Diagnosis Procedure".
Rear view camera malfunction. Replace rear view camera.
Refer to AV- 11 8 , "
Removal and Installa-
tion".
Revision: August 2015
2016 Versa Note

cardiagn.com

AV
NORMAL OPERATING CONDITIONAV-111
< SYMPTOM DIAGNOSIS > [DISPLAY AUDIO]
C
D
E
F
G H
I
J
K L
M B A
O P
NORMAL OPERATING CONDITION
DescriptionINFOID:0000000012432976
RELATED TO NOISE
The majority of the audio concerns are the result of outside causes (bad CD, electromagnetic interference,
etc.).
The following noise results from variations in field strength, such as fading noise and multi-path noise, or
external noise from trains and other sources. It is not a malfunction.
• Fading noise: This noise occurs because of variations in the field strength in a narrow range due to moun-
tains or buildings blocking the signal.
• Multi-path noise: This noise results from the waves sent directly from the broadcast station arriving at the antenna at a different time from the waves which reflect off mountains or buildings.
The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunctioning.
Check if noise is caused and/or changed by engine speed, ignition switch turned to each position, and opera-
tion of each piece of electrical equipment, and determine the cause.
NOTE:
The source of the noise can be found easily by listening to the noise while removing the fuses of electrical
components, one by one.
Type of Noise and Possible Cause
RELATED TO HANDS-FREE PHONE
Occurrence condition Possible cause
Occurs only when engine is ON. A continuous growling noise occurs. The speed of
the noise varies with changes in the engine speed.
• Ignition components
The occurrence of the noise is linked with the operation of the fuel pump. • Fuel pump condenser
Noise only occurs when various
electrical components are oper-
ating. A cracking or snapping sound occurs with the op-
eration of various switches.
• Relay malfunction, audio unit malfunction
The noise occurs when various motors are operat-
ing. • Motor case ground
•Motor
The noise occurs constantly, not just under certain conditions. • Rear defogger coil malfunction
• Open circuit in printed heater
• Poor ground of antenna feeder line
A cracking or snapping sound occurs while the vehicle is being driven, especially when
it is vibrating excessively. • Ground wire of body parts
• Ground due to improper part installation
• Wiring connections or a short circuit
Symptom
Cause and Counter measure
Does not recognize cellular phone connection (No connection is
displayed on the display at the guide). Some Bluetooth
® enabled cellular phones may not be recognized
by the in-vehicle phone module.
Refer to “RELATED TO HANDS-FREE PHONE (Check Compati-
bility)” in AV- 1 0 8 , "
Symptom Table".
Cannot use hands-free phone. Customer will not be able to use a hands-free phone under the fol-
lowing conditions:
• The vehicle is outside of the telephone service area.
• The vehicle is in an area where it is difficult to receive radio
waves; such as in a tunnel, in an underground parking garage,
near a tall building or in a mountainous area.
• The cellular phone is locked to prevent it from being dialed.
NOTE:
While a cellular phone is connected through the Bluetooth
® wire-
less connection, the battery power of the cellular phone may dis-
charge quicker than usual. The Bluetooth
® Hands-Free Phone
System cannot charge cellular phones.
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-112
< SYMPTOM DIAGNOSIS >[DISPLAY AUDIO]
NORMAL OPERATING CONDITION
The other party’s voice cannot be heard by hands-free phone.When the radio wave condition is not ideal or ambient sound is too
loud, it may be difficult to hear the other person’s voice during a
call.
Poor sound quality. Do not place the cellular phone in an area surrounded by metal or
far away from the in-vehicle phone module to prevent tone quality
degradation and wireless connection disruption.
Symptom
Cause and Counter measure
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-122
< REMOVAL AND INSTALLATION >[DISPLAY AUDIO]
MICROPHONE
MICROPHONE
Removal and InstallationINFOID:0000000012432987
REMOVAL
1. Remove the microphone finisher from the headlining by releas-
ing pawls (A) using a suitable tool.
2. Disconnect the harness connector from microphone and remove.
3. Separate the microphone from the finisher by releasing pawls (A) using a suitable tool.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
• Make sure to align the rib on the finisher with the slot in the microphone.
• Make sure to install the microphone with the arro ws pointing toward the RH side of the vehicle.
AWNIA3153ZZ
AWNIA3154ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
COMPONENT PARTSAV-129
< SYSTEM DESCRIPTION > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts LocationINFOID:0000000012432999
A. Front of headliner B. View with passenger seat removed C. Center of back door
AWNIA3648ZZ
No.Component Function
1. Rod antenna Refer to AV- 1 3 2 , "
Rod Antenna, Antenna Amp., Satellite Antenna and Antenna
Feeder".
2. Antenna base (antenna amp. and satellite
antenna)
3. Rear door speaker RH Refer to AV- 1 3 0 , "
Spe ak ers".
4. Front door speaker RH
5. Front camera Refer to AV- 1 3 2 , "
Front Camera".
6. Front door speaker LH Refer to AV- 1 3 0 , "
Spe ak ers".
7. Side camera Refer to AV- 1 3 2 , "
Side Cameras".
8. Rear door speaker LH Refer to AV- 1 3 0 , "
Spe ak ers".
9. AV control unit Refer to AV- 1 3 0 , "
AV Control Unit".
10. GPS antenna Refer to AV- 1 3 4 , "
GPS Antenna".
11. Steering wheel audio control switches Refer to AV- 1 3 1 , "
Steering Wheel Audio Control Switches".
12. Steering angle sensor Refer to AV- 1 3 2 , "
Steering Angle Sensor".
13. USB interface and AUX in jack Refer to AV- 1 3 1 , "
USB Interface and AUX In Jack".
14. Microphone Refer to AV- 1 3 1 , "
Microphone".
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
COMPONENT PARTSAV-131
< SYSTEM DESCRIPTION > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
USB Interface and AUX In JackINFOID:0000000012433002
• USB Interface and AUX in jack is installed in the console.
•iPod
® and USB memory can be connected to the AV control unit
through the USB interface.
• An external audio device can be connected to the AV control unit through the AUX in jack.
Steering Wheel Audio Control SwitchesINFOID:0000000012433003
• Steering wheel audio control switches are installed in the steering
wheel.
• Operations for audio and hands-free phone are possible.
• Switch is connected to the AV control unit.
MicrophoneINFOID:0000000012433004
• The microphone is installed in the roof in front of the map lamp
assembly.
• Power is supplied from the AV control unit.
Around View Monitor Control UnitINFOID:0000000012433005
• The around view monitor control unit is installed underneath the passenger seat.
• Vehicle width guide lines, predicted course line, vehicle front guid- ing line and vehicle side line, and vehicle icon are displayed and
combined with camera images.
ALNIA1523ZZ
ALNIA1659ZZ
JPNIA1448ZZ
JSNIA5395ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com