tire pressure NISSAN NOTE 2016 Service Repair Manual

BCS-8
< SYSTEM DESCRIPTION >[WITH INTELLIGENT KEY SYSTEM]
SYSTEM
BODY CONTROL SYSTEM : Fail-safe
INFOID:0000000012432307
BCM performs fail-safe control when the following DTCs are detected.
Intelligent Key system/engine start system Door lock function
DLK-23, "
DOOR LOCK FUNCTION : System De scription"
Warning functionDLK-27, "WARNING FUNCTION : System Description"
Key reminder functionDLK-27, "KEY REMINDER FUNCTION : System Descrip-
tion"
Engine start functionSEC-12, "INTELLIGENT KEY SYSTEM/ENGINE START
FUNCTION : System Description"
Power window system
PWC-8, "System Description"
RAP (retained accessory power) systemBCS-28, "RETAINED PWR : CONSULT Function (BCM - RE-
TAINED PWR)"
TPMS (tire pressure monito
ring system) (if equipped) WT-8, "TIRE PRESSURE MONITORING SYSTEM : System
Description"
System
Reference
CONSULT DisplayFail-safe Cancellation
B2192: ID DISCORD BCM-ECM Inhibit engine cranking Erase DTC
B2193: CHAIN OF BCM-ECM Inhibit engine cranking Erase DTC
B2195: ANTI SCANNING Inhibit engine cranking Ignition switch ON → OFF
B2196: DONGLE NG Inhibit engine cranking Erase DTC
B2198: NATS ANTENNA AMP Inhibit engine cranking Erase DTC
B2557: VEHICLE SPEED —When the following CAN signal status (vehicle speed signal) becomes
consistent
• Vehicle speed signal (ABS)
• Vehicle speed signal (Meter)
B2601: SHIFT P SIGNAL —500 ms after the following signal reception status becomes consistent
• Park position switch signal
• P range signal (CAN)
B2602: SHIFT P DIAG —5 seconds after the following BCM recognition conditions are fulfilled
• Ignition switch is in the ON position
• Park position switch signal: P position (push selector button) or ex-
cept P position (9 – 16 V)
• Vehicle speed: 4 km/h (2.5 MPH) or more
B2603: SHIFT POSITION —500 ms after any of the following BCM recognition conditions are fulfilled
•Status 1
- Ignition switch is in the ON position
- Park position switch signal: P position (push selector button) or ex-
cept P position (9 – 16 V)
- P/N position signal: Except P and N positions (0 – 1.5 V)
•Status 2
- Ignition switch is in the ON position
- Park position switch signal: P position (release selector button) (0 – 1.5 V)
- P/N position signal: P or N positions (9 – 16 V)
B2604: SHIFT PN DIAG CAN —500 ms after any of the following BCM recognition conditions are fulfilled
•Status 1
- Ignition switch is in the ON position
- P/N position signal: P or N position (9 – 16 V)
- Shift position signal (CAN): P or N position
•Status 2
- Ignition switch is in the ON position
- P/N position signal: Except P and N positions (0 – 1.5 V)
- Shift position signal (CAN): Except P and N position
Revision: August 2015
2016 Versa Note

cardiagn.com

BCS-14
< SYSTEM DESCRIPTION >[WITH INTELLIGENT KEY SYSTEM]
SYSTEM
• BCM switches the status (control mode) by itself wit
h the power saving control function. It performs the sleep
request to each unit (IPDM E/R and combination mete r) that operates with the ignition switch OFF.
Normal mode (wake-up)- CAN communication is normally performed with other units
- Each control with BCM is operating properly
CAN communication sleep mode (CAN sleep)- CAN transmission is stopped
- Control with BCM only is operating
Low power consumption mode (BCM sleep)- Low power consumption control is active
- CAN transmission is stopped
LOW POWER CONSUMPTION CONTROL WITH BCM
BCM reduces the power consumption with the following operation in the low power consumption mode.
• The reading interval of each switch changes from 10 ms interval to 60 ms interval.
Sleep mode activation
• BCM receives the sleep-ready signal (ready) from IPDM E/R and combination meter via CAN communica-
tion.
• BCM transmits the sleep wake up signal (sleep) to each unit when all of the CAN sleep conditions are ful- filled.
• Each unit stops the transmission of CAN communication with the sleep wakeup signal. BCM is in CAN com- munication sleep mode.
• BCM is in the low power consumption mode and perform s the low power consumption control when all of the
BCM sleep conditions are fulfilled with CAN sleep condition.
Sleep condition
Wake-up operation
• BCM transmits the sleep wake up signal (wake up) to each unit when any of the CAN wake-up conditions are fulfilled. It changes from the low power consumption mode or the CAN communication sleep mode to the
normal mode.
• Each unit starts the transmission of CAN communication with the sleep wake up signal. In addition, the com- bination meter transmits the wake up signal to BCM via CAN communication to report the CAN communica-
tion start.
CAN sleep condition BCM sleep condition
• Receiving the sleep-ready signal (ready) from all units
• Ignition switch: OFF
• Vehicle security system alarm: No operation
• Warning lamp: Not operation
• Intelligent Key system buzzer: No operation
• Brake switch: OFF
• Turn signal indicator lamp: No operation
•Exterior lamp: OFF
• Door lock status: No change
• CONSULT communication status: No communication
• Meter display signal: Non-transmission
• Door switch status: No change
• Rear window defogger: OFF • Interior room lamp battery saver: Time out
• RAP system: OFF
• Push-button ignition switch (push switch) illumination: OFF
• NATS: No operation
• Remote keyless entry receiver communication status: No com-
munication
• Tire pressure monitoring system:Stop
BCM wake-up condition CAN wake-up condition
• Front door lock assembly LH (key cylinder switch): Lock or unlock
• Door lock switch: OFF →ON
• Door unlock switch: OFF→ON
• Remote keyless entry receiver: Receiving valid keyfob • Receiving the sleep-ready signal (Not-ready) from any units
• Push-button ignition switch (push switch): OFF
→ON
• Hazard switch: OFF →ON
• PASSING switch: OFF →ON, ON →OFF
• TAIL LAMP switch: OFF →ON
• Front door switch LH: OFF →ON, ON→OFF
• Front door switch RH: OFF → ON, ON → OFF
• Front outside handle LH request switch: OFF →ON
• Front outside handle RH request switch: OFF→ON
• Stop lamp switch 2 signal: ON
• Remote keyless entry receiver: Receiving valid keyfob
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS-28
< SYSTEM DESCRIPTION >[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
RETAINED PWR
RETAINED PWR : CONSULT Function (BCM - RETAINED PWR)INFOID:0000000012432328
DATA MONITOR
SIGNAL BUFFER
SIGNAL BUFFER : CONSULT Func
tion (BCM - SIGNAL BUFFER)INFOID:0000000012432329
DATA MONITOR
AIR PRESSURE MONITOR
AIR PRESSURE MONITOR : CONSULT Fu nction (BCM - AIR PRESSURE MONI-
TOR)
INFOID:0000000012432330
NOTE:
The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions. Refer to the Signal Tech
II User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
• Check Intelligent Key relative signal strength
• Confirm vehicle Intelligent Key antenna signal strength
SELF DIAGNOSTIC RESULT
NOTE:
Before performing self diagnostic result, be sure to register the ID, or else the actual malfunction may be differ-
ent from that displayed on CONSULT.
Refer to BCS-50, "
DTCIndex".
DATA MONITOR
ACTIVE TEST
Monitor Item [Unit] Description
DOOR SW-DR [On/Off] Indicates condition of front door switch LH.
DOOR SW-AS [On/Off] Indicates condition of front door switch RH.
Monitor Item [Unit] Description
PUSH SW [On/Off] Indicates condition of the push-button ignition switch.
Monitor Item [Unit] Description
AIR PRESS FL [kPa, kg/cm
2 or Psi] Indicates air pressure of front LH tire.
AIR PRESS FR [kPa, kg/cm
2 or Psi] Indicates air pressure of front RH tire.
AIR PRESS RR [kPa, kg/cm
2 or Psi] Indicates air pressure of rear RH tire.
AIR PRESS RL [kPa, kg/cm
2 or Psi] Indicates air pressure of rear LH tire.
ID REGST FL1 [Done/Yet] Indicates ID registration status of front LH transmitter.
ID REGST FR1 [Done/Yet] Indicates ID registration status of front RH transmitter.
ID REGST RR1 [Done/Yet] Indicates ID registration status of rear RH transmitter.
ID REGST RL1 [Done/Yet] Indicates ID registration status of rear LH transmitter.
WARNING LAMP [Off/On] Indicates condition of low tire pressure warning lamp in combination meter.
BUZZER [Off/On] Indicates condition of buzzer in combination meter.
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
DIAGNOSIS SYSTEM (BCM)BCS-29
< SYSTEM DESCRIPTION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
NWORK SUPPORT
PANIC ALARM
PANIC ALARM : CONSULT Function (BCM - PANIC ALARM)INFOID:0000000012432331
ACTIVE TEST
Test Item
Description
HORN This test is able to check horn operation [On].
FLASHER This test is able to check turn signal lamp operation [Off/LH/RH].
ID REGIST WARNING This test is able to check ID registration warning chime operation [On/Off].
WARNING LAMP This test is able to check tire pressure warning lamp operation [On/Off].
Support Item Description
ID READ The registered ID number is displayed.
ID REGIST Refer to WT-22, "
Description".
Test Item Description
VEHICLE SECURITY HORN This te st is able to check panic alarm operation [On].
HEAD LAMP (HI) This test is able to check head lamp HI operation [On].
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS-30
< ECU DIAGNOSIS INFORMATION >[WITH INTELLIGENT KEY SYSTEM]
BCM
ECU DIAGNOSIS INFORMATION
BCM
Reference ValueINFOID:0000000012432332
NOTE:
The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions. Refer to the Signal Tech
II User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
• Check Intelligent Key relative signal strength
• Confirm vehicle Intelligent Key antenna signal strength
VALUES ON THE DIAGNOSIS TOOL
Monitor Item
Condition Value/Status
AIR COND SW A/C switch OFF
Off
A/C switch ON On
AIR PRESS FL Front left tire air pressure value
kPa, kg/cm
2, psi
AIR PRESS FR Front right tire air pressure value
kPa, kg/cm
2, psi
AIR PRESS RL Rear left tire air pressure value
kPa, kg/cm
2, psi
AIR PRESS RR Rear right tire air pressure value
kPa, kg/cm
2, psi
BRAKE SW 1 When the brake pedal is released
On
When the brake pedal is depressed Off
BRAKE SW2 Brake pedal released
Off
Brake pedal depressed On
BUZZER Buzzer in combination meter OFF
Off
Buzzer in combination meter ON On
CDL LOCK SW Door lock/unlock switch does not operate
Off
Press door lock/unlock switch to the LOCK side On
CDL UNLOCK SW Door lock/unlock switch does not operate
Off
Press door lock/unlock switch to the UNLOCK side On
CLUCH SW Clutch pedal depressed
On
Clutch pedal released Off
CONFRM ID ALL The key ID does not match any key ID registered to BCM. Yet
The key ID matches any key ID registered to BCM.
DONE
CONFIRM ID4 The key ID does not match the fourth key ID registered to BCM. Yet
The key ID matches the fourth key ID registered to BCM.
DONE
CONFIRM ID3 The key ID does not match the third key ID registered to BCM. Yet
The key ID matches the third key ID registered to BCM.
DONE
CONFIRM ID2 The key ID does not match the second key ID registered to BCM. Yet
The key ID matches the second key ID registered to BCM. DONE
CONFIRM ID1 The key ID does not match the first key ID registered to BCM. Yet
The key ID matches the first key ID registered to BCM.
DONE
DETE SW -IPDM When selector lever is in P position
Off
When selector lever is in any position other than P On
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
BCM
BCS-33
< ECU DIAGNOSIS INFORMATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
RR WASHER SW
Rear washer switch OFF Off
Rear washer switch ON
On
RR WIPER INT Rear wiper switch OFF
Off
Rear wiper switch INT On
RR WIPER ON Rear wiper switch OFF
Off
Rear wiper switch ON On
RR WIPER STOP Any position other than rear wiper stop position
Off
Rear wiper stop position On
SFT N-MET When selector lever is in any position other than N
Off
When selector lever is in N position On
SFT P-MET When selector lever is in any position other than P
Off
When selector lever is in P position On
SFT PN -IPDM When selector lever is in any position other than P or N
Off
When selector lever is in P or N position On
SFT PN/N SW When selector lever is in any position other than P or N
Off
When selector lever is in P or N position On
TAIL LAMP SW Other than lighting switch 1ST and 2ND
Off
Lighting switch 1ST or 2ND On
TP 4 The ID of fourth key is not registered to BCM
Yet
The ID of fourth key is registered to BCM DONE
TP 3 The ID of third key is not registered to BCM
Yet
The ID of third key is registered to BCM DONE
TP 2 The ID of second key is not registered to BCM
Yet
The ID of second key is registered to BCM DONE
TP 1 The ID of first key is not registered to BCM
Yet
The ID of first key is registered to BCM DONE
TURN SIGNAL L Turn signal switch OFF
Off
Turn signal switch LH On
TURN SIGNAL R Turn signal switch OFF
Off
Turn signal switch RH On
UNLK SEN-DR Driver door UNLOCK status
Off
Driver door LOCK status On
VEH SPEED 1 While driving, equivalent to speedometer reading mph, km/h
VEH SPEED 2 While driving, equivalent to speedometer reading mph, km/h
WARNING LAMP Low tire pressure warning lamp in combination meter OFF Off
Low tire pressure warning lamp in combination meter ON
On
Monitor Item
Condition Value/Status
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS-50
< ECU DIAGNOSIS INFORMATION >[WITH INTELLIGENT KEY SYSTEM]
BCM
DTC Index
INFOID:0000000012432335
NOTE:
The details of time display are as follows.
• CRNT: A malfunction is detected now.
• PAST: A malfunction was detected in the past.
IGN counter is displayed on Freeze Frame Data.
5 • B2621: INSIDE ANTENNA 1
• B2622: INSIDE ANTENNA 2
• B2623: INSIDE ANTENNA 3
6 • B2626: OUTSIDE 1 ANTENNA
• B2627: OUTSIDE 2 ANTENNA
• B2628: OUTSIDE 3 ANTENNA
7 • C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL
• C1708: [NO DATA] FL
• C1709: [NO DATA] FR
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL
• C1716: [PRESS DATA ERR] FL
• C1717: [PRESS DATA ERR] FR
• C1718: [PRESS DATA ERR] RR
• C1719: [PRESS DATA ERR] RL
• C1729: VHCL SPEED SIG ERR
Priority DTC
CONSULT display Fail-safe
Freeze Frame Data
•Vehicle Speed
•Odo/Trip Meter
•Vehicle Condition Intelligent Key
warning lamp
ON Tire pressure monitor
warning lamp ON Reference page
No DTC is detected.
further testing
may be required. —— — — —
U1000: CAN COMM CIRCUIT — —— — BCS-63
U1010: CONTROL UNIT (CAN) — —— — BCS-64
U0415: VDC CAN CIR2 ×— ×— BCS-65
B2192: ID DISCORD BCM-ECM ×—— — SEC-54
B2193: CHAIN OF BCM-ECM×—— — SEC-55
B2195: ANTI SCANNING×—— — SEC-56
B2196: DONGLE NG×—— — SEC-57
B2198: NATS ANTENNA AMP×—— — SEC-59
B2555: STOP LAMP CIRCUIT —××—SEC-62
B2556: ENG START SW —×× —SEC-65
B2557: VEHICLE SPEED ×× × —SEC-67
B2562: LOW VOLTAGE —× —— BCS-66
B2601: SHIFT P SIGNAL×× × —SEC-68
B2602: SHIFT P DIAG ×× × —SEC-70
B2603: SHIFT POSITION ×× × —SEC-73
B2604: SHIFT PN DIAG CAN ×× × —SEC-77
B2605: SHIFT PN DIAG IPDM ×× × —SEC-80
B2608: STARTER RELAY ×× × —SEC-82
B260F: ECM CAN COMM ×× × —SEC-84
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
BCM
BCS-51
< ECU DIAGNOSIS INFORMATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
B2614: ACC RELAY REQ FB —
××—PCS-56
B2615: IGN RELAY3 REQ FB — ××—PCS-58
B2616: IGN RELAY2 REQ FB — ××—PCS-60
B2618: IGN RELAY1 REQ FB — ××—PCS-62
B261A: ENGINE SW —×× —PCS-63
B261F: ASCD CANCEL SW —×× —SEC-85
B2620: NEUTRAL SW —×× —SEC-88
B2621: INSIDE ANTENNA 1 —× —— DLK-65
B2622: INSIDE ANTENNA 2—× —— DLK-67
B2623: INSIDE ANTENNA 3—× —— DLK-69
B2626: OUTSIDE 1 ANTENNA — ×—— DLK-73
B2627: OUTSIDE 2 ANTENNA — ×—— DLK-71
B2628: OUTSIDE 3 ANTENNA — ×—— DLK-75
B26E8: CLUTCH SW×× × —SEC-91
B26F1: IGN RELAY OFF ×× × —PCS-65
B26F2: IGN RELAY ON ×× × —PCS-66
B26F3: START CONT RLY ON ×× × —SEC-94
B26F4: START CONT RLY OFF ×× × —SEC-95
B26F6: BCM —×× —PCS-68
B26F7: BCM ×× × —SEC-96
B26FB: CLUTCH SWITCH —×× —SEC-97
B26FC: KEY REGISTRATION — ××—SEC-98
C1704: LOW PRESSURE FL — —— ×
WT-25
C1705: LOW PRESSURE FR — —— ×
C1706: LOW PRESSURE RR — —— ×
C1707: LOW PRESSURE RL — —— ×
C1708: [NO DATA] FL —— — ×
WT-27
C1709: [NO DATA] FR —— — ×
C1710: [NO DATA] RR —— — ×
C1711: [NO DATA] RL —— — ×
C1716: [PRESS DATA ERR] FL — —— ×
WT-30
C1717: [PRESS DATA ERR] FR — —— ×
C1718: [PRESS DATA ERR] RR — —— ×
C1719: [PRESS DATA ERR] RL — —— ×
C1729: VHCL SPEED SIG ERR — —— ×WT-32
CONSULT display Fail-safe Freeze Frame Data
•Vehicle Speed
•Odo/Trip Meter
•Vehicle Condition Intelligent Key
warning lamp ON Tire pressure monitor
warning lamp ON Reference page
Revision: August 2015
2016 Versa Note

cardiagn.com

BCS
SYSTEMBCS-79
< SYSTEM DESCRIPTION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
BODY CONTROL SYSTEM : Fail-safeINFOID:0000000012432364
FAIL-SAFE CONTROL BY DTC
BCM performs fail-safe control when any DTC are detected.
FAIL-SAFE CONTROL OF COMBINATION SWIT
CH READING FUNCTION CAUSED BY LOW
POWER SUPPLY VOLTAGE
If voltage of battery power supply lower, BCM maintains combination switch reading to the status when input
voltage is less than approximately 9 V.
NOTE:
When voltage of battery power supply is approximately 9 V or more, combination switch reading function
returns to normal operation.
COMBINATION SWITCH READING SYSTEM
COMBINATION SWITCH READING SYSTEM : System DescriptionINFOID:0000000012432365
SYSTEM DIAGRAM
Combination Switch Circuit (With Variable Intermittent Wipers)
RAP (retained accessory power) system BCS-98, "RETAINED PWR : CONSULT Function (BCM - RE-
TAINED PWR)"
Tire pressure monitoring system (if equipped)WT-8, "TIRE PRESSURE MONITORING SYSTEM : System
Description"
System
Reference
Display contents of CONSULTFail-safe Cancellation
B2190: NATS ANTENNA AMP Inhibit engine cranking Erase DTC
B2191: DIFFERENCE OF KEY Inhibit engine cranking Erase DTC
B2192: ID DISCORD BCM-ECM Inhibit engine cranking Erase DTC
B2193: CHAIN OF BCM-ECM Inhibit engine cranking Erase DTC
B2195: ANTI SCANNING Inhibit engine cranking Ignition switch ON → OFF
B2196: DONGLE NG Inhibit engine cranking Erase DTC
AWMIA1427GB
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
DIAGNOSIS SYSTEM (BCM)BCS-99
< SYSTEM DESCRIPTION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
AIR PRESSURE MONITOR
AIR PRESSURE MONITOR : CONSULT Function (BCM - AIR PRESSURE MONI-
TOR)
INFOID:0000000012432387
NOTE:
The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions. Refer to the Signal Tech
II User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure repor
ted by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
• Test remote keyless entry keyfob relative signal strength
SELF DIAGNOSTIC RESULT
NOTE:
Before performing self diagnostic result, be sure to register the ID, or else the actual malfunction may be differ-
ent from that displayed on CONSULT.
Refer to BCS-115, "
DTCIndex".
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
PANIC ALARM
Monitor Item [Unit] Description
BRAKE SW [On/Off] Indicates condition of stop lamp
switch signal received from ABS actuator and electric unit
(control unit) on CAN communication line.
Monitor Item [Unit] Description
AIR PRESS FL [kPa, kg/cm
2 or Psi] Indicates air pressure of front LH tire.
AIR PRESS FR [kPa, kg/cm
2 or Psi] Indicates air pressure of front RH tire.
AIR PRESS RR [kPa, kg/cm
2 or Psi] Indicates air pressure of rear RH tire.
AIR PRESS RL [kPa, kg/cm
2 or Psi] Indicates air pressure of rear LH tire.
ID REGST FL1 [Done/Yet] Indicates ID registration status of front LH transmitter.
ID REGST FR1 [Done/Yet] Indicates ID registration status of front RH transmitter.
ID REGST RR1 [Done/Yet] Indicates ID registration status of rear RH transmitter.
ID REGST RL1 [Done/Yet] Indicates ID registration status of rear LH transmitter.
WARNING LAMP [Off/On] Indicates condition of low tire pressure warning lamp in combination meter.
BUZZER [Off/On] Indicates condition of buzzer in combination meter.
Test Item Description
HORN This test is able to check horn operation [On].
WARNING LAMP This test is able to check tire pressure warning lamp operation [On/Off].
ID REGIST WARNING This test is able to check ID registration warning chime operation [On/Off].
FLASHER This test is able to check turn signal lamp operation [Off/LH/RH].
Support Item Description
ID READ The registered ID number is displayed.
ID REGIST Refer to WT-22, "
Description".
Revision: August 2015 2016 Versa Note

cardiagn.com