service indicator NISSAN NOTE 2016 Service Owner's Manual

ADDITIONAL SERVICE WHEN REPLACING TCMTM-125
< BASIC INSPECTION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
ADDITIONAL SERVICE WHEN REPLACING TCM
DescriptionINFOID:0000000012431042
When replacing the TCM, perform the following work. For work procedure, refer to TM-125, "Work Procedure".
TCM PROGRAMMING• Since vehicle specifications are not yet written in a new TCM, it is necessary to write them with CONSULT.
CAUTION:
When replacing TCM, save TCM data on CONSULT before removing TCM.
LOADING AND STORING OF CALIBRATION DATA• The TCM acquires calibration data (individual characteristic value) of each solenoid that is stored in the
ROM assembly (in the control valve). This enables the TCM to perform accurate control. After the TCM is
replaced, check that the calibrati on data is correctly loaded and stored.
CALIBRATION OF G SENSOR
• TCM stores calibration data (inherent characteristic value) of G sensor to provide accurate control. There-
fore, it is required to perform calibration of G sensor after the replacement of TCM.
CAUTION:
When replacing TCM and transaxle assembly simultaneously, replace transaxle assembly first and
then replace TCM.
Work ProcedureINFOID:0000000012431043
1.CHECK NEW TCM PART NUMBER
Check new TCM part number to see whether it is blank TCM or not.
NOTE:
• Part number of blank TCM is 310F6-XXXXX.
• Check the part number when ordering TCM or with the one included in the label on the container box.
Is the new TCM a blank TCM?
YES >> GO TO 2.
NO >> GO TO 3.
2.SAVING TCM DATA (VEHICLE SPECIFICATIONS)
NOTE:
Save necessary data stored in TCM in CONSULT according to the following instructions: With CONSULT
1. Turn ignition switch OFF.
2. Turn ignition switch ON.
3. Select “Re/programming, Configuration”.
4. Select “AT/CVT”.
NOTE:
If “AT/CVT” is not displayed and TCM data cannot be saved on CONSULT, GO TO 3.
5. Select “Programming”.
6. Save TCM data on CONSULT according to the CONSULT display.
>> GO TO 3.
3.REPLACE TCM
1. Turn ignition switch OFF and wait for 10 seconds.
2. Replace TCM. Refer to TM-239, "
Removal and Installation".
>> GO TO 4.
4.LOAD CALIBRATION DATA
1. Shift the selector lever to the “P” position.
2. Turn ignition switch ON.
3. Check that "P" is displayed on shift position indicator on combination meter. NOTE:
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-126
< BASIC INSPECTION >[CVT: RE0F11A]
ADDITIONAL SERVICE WHEN REPLACING TCM
Displayed approximately 4 – 5 seconds after the
selector lever is moved to the “P” position.
Does the shift position indicator display
“P”?
YES >> GO TO 5.
NO >> GO TO 8.
5.STORE CALIBRATION DATA
1. Turn ignition switch OFF and wait for 5 seconds.
2. Turn ignition switch ON.
Does the shift position indicator display
“P” at the same time when turning ON the ignition switch?
YES-1 (New TCM is blank)>>GO TO 6.
YES-2 (New TCM is not blank)>>GO TO 7.
NO >> Check harness between battery and TCM harness connector terminal. Refer to TM-182, "
Diagno-
sis Procedure".
6.WRITE TCM DATA (VEHICLE SPECIFICATIONS)
NOTE:
Write data saved in CONSULT into a new TCM according to the following instructions: With CONSULT
1. Select “Programming”.
2. Perform programming according to the CONSULT display.
>> GO TO 7.
7.CALIBRATE G SENSOR
Refer to TM-130, "
Description".
>> WORK END
8.DETECT MALFUNCTIONING ITEM
Check the following items:
• Harness between the TCM and the ROM assembly insi de the transaxle assembly is open or shorted.
• Disconnected, loose, bent, collapsed, or otherwise abnormal connector housing terminals
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace the malfunctioning parts.
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-128
< BASIC INSPECTION >[CVT: RE0F11A]
ADDITIONAL SERVICE WHEN REPLACING
CONTROL VALVE OR TRANSAXLE
ASSEMBLY
Is the indicated value of “CALIB DATA” equal to the value shown in the table?
YES >> GO TO 3.
NO >> GO TO 1.
3.LOAD CALIBRATION DATA
1. Shift the selector lever to the “P” position.
2. Check that “P” is displayed on shift position indicator on combination meter. NOTE:
Displayed approximately 4 – 5 seconds after the selector lever is moved to the “P” position.
Does shift position indicator display
“P”?
YES >> GO TO 5.
NO >> GO TO 4.
4.DETECT MALFUNCTIONING ITEMS
Check the following items:
• Harness between the TCM and the ROM assembly insi de the transaxle assembly is open or shorted.
• Disconnected, loose, bent, collapsed, or otherwise abnormal connector housing terminals
Is the inspection result normal?
YES >> GO TO 1.
NO >> Repair or replace the malfunctioning parts.
5.STORE CALIBRATION DATA
1. Turn ignition switch OFF and wait for 5 seconds.
2. Turn ignition switch ON.
Does the shift position indicator display
“P” at the same time when turning ON the ignition switch?
YES >> GO TO 6.
NO >> Check harness between battery and TCM harness connector terminal.
6.ERASE THE CVT FLUID DEGRADATION LEVEL DATA
With CONSULT
1. Select “WORK SUPPORT” in “TRANSMISSION”.
UNIT CLB ID5 00OFFSET2 PRI 0
UNIT CLB ID6 00OFFSET2 H/R 0
UNIT CLB ID7 00OFFSET2 L/B 0
UNIT CLB ID8 00INIT OFFSET H/R A 0
UNIT CLB ID9 00INIT OFFSET H/R B 0
UNIT CLB ID10 00INIT OFFSET H/R C 0
UNIT CLB ID11 00INIT OFFSET H/R D 0
GAIN LU 256INIT OFFSET H/R E 0
GAIN PL 256INIT OFFSET H/R F 0
GAIN PRI 256INIT OFSET LB A 0
GAIN HC/RB 256INIT OFSET LB B 0
GAIN L/B 256INIT OFSET LB C 0
OFFSET LU 0INIT OFSET LB D 0
OFFSET PL 0INIT OFSET LB E 0
OFFSET PRI 0INIT OFSET LB F 0
OFFSET HC/RB 0LB INITIALIZE LEARN −1
OFFSET L/B 0HC INITIALIZE LEARN −1
MAP NO LU 00LB INITIALIZE TEMP FF
MAP NO PL 00LB INITIALIZE TEMP FF
MAP NO PRI 00
Item name
Display value Item nameDisplay value
Revision: August 2015 2016 Versa Note

cardiagn.com