fuel fill door release NISSAN NOTE 2016 Service Repair Manual

DLK-8
HOOD LOCK RELEASE CABLE ............................293
HOOD LOCK RELEASE CABLE : Removal and
Installation .............................................................
293
HOOD LOCK RELEASE HANDLE ........................ ..294
HOOD LOCK RELEASE HANDLE : Removal and
Installation ........................................................... ..
294
FRONT DOOR LOCK ......................................295
Exploded View ..................................................... ..295
DOOR LOCK .......................................................... ..295
DOOR LOCK : Removal and Installation ...............295
INSIDE HANDLE .................................................... ..296
INSIDE HANDLE : Removal and Installation .........296
OUTSIDE HANDLE ................................................ ..297
OUTSIDE HANDLE : Removal and Installation .....297
REAR DOOR LOCK ....................................... .299
Exploded View ..................................................... ..299
DOOR LOCK .......................................................... ..299
DOOR LOCK : Removal and Installation ...............299
INSIDE HANDLE .................................................... ..300
INSIDE HANDLE : Removal and Installation .........300
OUTSIDE HANDLE ................................................ ..301
OUTSIDE HANDLE : Removal and Installation .....301
BACK DOOR LOCK ....................................... .303
Exploded View ..................................................... ..303
BACK DOOR LOCK ............................................... .303
BACK DOOR LOCK : Removal and Installation ...303
OUTSIDE HANDLE ................................................ .303
OUTSIDE HANDLE : Removal and Installation ....303
FUEL FILLER LID OPENER ............................305
Exploded View ..................................................... .305
FUEL FILLER LID .................................................. .305
FUEL FILLER LID : Removal and Installation .......305
FUEL FILLER OPENER CABLE ........................... .306
FUEL FILLER OPENER CABLE : Removal and
Installation .............................................................
306
FUEL FILLER LID LOCK ....................................... .306
FUEL FILLER LID LOCK : Removal and Installa-
tion ........................................................................
307
DOOR SWITCH ................................................308
Removal and Installation .......................................308
REMOTE KEYLESS ENTRY RECEIVER ...... ..309
Removal and Installation .......................................309
KEYFOB BATTERY .........................................310
Removal and Installation .......................................310
STEERING LOCK UNIT ...................................311
Exploded View ..................................................... .311
Removal and Installation - Steering lock unit ........311
Removal and Installation - Ignition switch ............ .312
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-166
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
HOOD LOCK
• After installation, perform hood assembl
y adjustment procedure. Refer to DLK-141, "HOOD ASSEM-
BLY : Adjustment".
• After adjustment, perform hood lock control inspection. Refer to DLK-166, "
HOOD LOCK : Inspec-
tion".
HOOD LOCK : InspectionINFOID:0000000012430120
HOOD LOCK INSPECTION
NOTE:
If hood lock cable is bent or deformed, replace it. Refer to DLK-165, "
HOOD LOCK : Removal and Installa-
tion".
1. Check that secondary latch is properly engage with secondary striker with hoods own weight.
2. While operating hood lock release lever, carefully check that the front end of hood assembly is raised by approximately 20.0 mm (0.79 in). Also check that hood lock release lever returns to original position.
3. Check that hood lock release lever operates at 49 N (5.0 kg-m, 11.0 ft-lb) or below.
4. Install so that static closing force of hood is 315-490 N (32.1-50.0 kg-m, 70.8-110.2 ft-lb).
5. Check hood lock assembly lubrication condition. If necessary, apply a suitable multi-purpose grease.
HOOD LOCK RELEASE CABLE
HOOD LOCK RELEASE CABLE : Removal and InstallationINFOID:0000000012430121
REMOVAL
1. Disconnect hood lock release cable from hood lock. Refer to DLK-165, "Exploded View".
2. Remove radiator cap adapter bracket bolt (A) and radiator reser- voir tank bolt (B).
3. Remove fender protector (LH). Refer to EXT-38, "
Removal and Installation".
4. Release hood lock control cable clips using a suitable tool.
5. Remove hood lock/fuel filler door release handle. Refer to DLK-167, "
HOOD LOCK RELEASE HANDLE :
Removal and Installation".
6. Remove dash side finisher (LH). Refer to INT-24, "
DASH SIDE FINISHER : Removal and Installation".
7. Remove grommet on the lower dash and pull the hood lock release cable into the passenger compart- ment.
CAUTION:
While pulling, be careful no t to damage (peel) the outsid e of the hood lock release cable.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Be careful not to bend cable too much, keep the radius 100 mm (3.94 in) or more.
• Check that hood lock release cable is properly engaged with hood lock.
JMKIA8027ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

HOOD LOCKDLK-167
< REMOVAL AND INSTALLATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
• Check that cable is not offset from the positioning grommet, and apply the sealant to the grommet (at * mark).
HOOD LOCK RELEASE HANDLE
HOOD LOCK RELEASE HANDLE : Removal and InstallationINFOID:0000000012430122
REMOVAL
1. Remove hood lock/fuel filler door release handle bolts (A).
2. Disconnect hood lock release cable from hood lock/fuel filler door release handle and remove.
INSTALLATION
Installation is in the reverse order of removal.
PIIB5801E
AWKIA2498ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

HOOD LOCKDLK-293
< REMOVAL AND INSTALLATION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
• After installation, perform hood assem bly adjustment procedure. Refer to DLK-269, "HOOD ASSEM-
BLY : Adjustment".
• After adjustment, perform hood lo ck control inspection. Refer to DLK-293, "
HOOD LOCK : Inspec-
tion".
HOOD LOCK : InspectionINFOID:0000000012430266
HOOD LOCK INSPECTION
NOTE:
If hood lock cable is bent or deformed, replace it. Refer to DLK-292, "
HOOD LOCK : Removal and Installa-
tion".
1. Check that secondary latch is properly engage with secondary striker with hoods own weight.
2. While operating hood lock release lever, carefully check that the front end of hood assembly is raised by approximately 20.0 mm (0.79 in). Also check that hood lock release lever returns to original position.
3. Check that hood lock release lever operates at 49 N (5.0 kg-m, 11.0 ft-lb) or below.
4. Install so that static closing force of hood is 315-490 N (32.1-50.0 kg-m, 70.8-110.2 ft-lb).
5. Check hood lock assembly lubrication condition. If necessary, apply a suitable multi-purpose grease.
HOOD LOCK RELEASE CABLE
HOOD LOCK RELEASE CABLE : Removal and InstallationINFOID:0000000012430267
REMOVAL
1. Disconnect hood lock release cable from hood lock. Refer to DLK-292, "Exploded View".
2. Remove radiator cap adapter bracket bolt (A) and radiator reser- voir tank bolt (B).
3. Remove fender protector (LH). Refer to EXT-38, "
Removal and Installation".
4. Release hood lock control cable clips using a suitable tool.
5. Remove hood lock/fuel filler door release handle. Refer to DLK-167, "
HOOD LOCK RELEASE HANDLE :
Removal and Installation".
6. Remove dash side finisher (LH). Refer to INT-24, "
DASH SIDE FINISHER : Removal and Installation".
7. Remove grommet on the lower dash and pull the hood lock release cable into the passenger compart- ment.
CAUTION:
While pulling, be caref ul not to damage (peel) the outsi de of the hood lock release cable.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Be careful not to bend cable too much, keep the radius 100 mm (3.94 in) or more.
• Check that hood lock release cable is properly engaged with hood lock.
JMKIA8027ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-294
< REMOVAL AND INSTALLATION >[WITHOUT INTELLIGENT KEY SYSTEM]
HOOD LOCK
• Check that cable is not offset
from the positioning grommet,
and apply the sealant to the grommet (at * mark).
HOOD LOCK RE LEASE HANDLE
HOOD LOCK RELEASE HANDLE : Removal and InstallationINFOID:0000000012430268
REMOVAL
1. Remove hood lock/fuel filler door release handle bolts (A).
2. Disconnect hood lock release cable from hood lock/fuel filler door release handle and remove.
INSTALLATION
Installation is in the reverse order of removal.
PIIB5801E
AWKIA2498ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

IP-24
< REMOVAL AND INSTALLATION >
INSTRUMENT LOWER PANEL LH
INSTRUMENT LOWER PANEL LH
Removal and InstallationINFOID:0000000012430786
REMOVAL
1. Remove data link connector from instrument lower panel LH.
2. Remove bolts (A) and position hood lock/fuel filler door releasehandle aside.
3. Remove instrument lower panel LH.
a. Release instrument lower panel LH metal clips and pawls using a suitable tool. CAUTION:
Release pawls and metal clips slowly so that they are not damaged.
b. Disconnect the harness connectors from instrument lower panel LH and remove.
INSTALLATION
Installation is in the reverse order of removal.
JMKIA7998ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com