ignition switch NISSAN NOTE 2016 Service Owner's Guide

AV-100
< DTC/CIRCUIT DIAGNOSIS >[DISPLAY AUDIO]
REAR VIEW CAMERA IMAGE SIGNAL CIRCUIT
REAR VIEW CAMERA IMAGE SIGNAL CIRCUIT
Diagnosis ProcedureINFOID:0000000012432970
Regarding Wiring Diagram information, refer to
AV-80, "Wiring Diagram".
1.CHECK REVERSE INPUT SIGNAL
1. Turn ignition switch ON.
2. Shift the selector lever to R (reverse).
3. Check voltage between audio unit connector M40 and ground.
Is inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness or connectors.
2.CHECK CAMERA POWER SUPPLY CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect audio unit connector M40 and rear view camera connector.
3. Check continuity between audio unit connecto r M40 and rear view camera connector D501.
4. Check continuity between audio unit connector M40 and ground.
Is inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness or connectors.
3.CHECK CAMERA POWER SUPPLY VOLTAGE
1. Connect audio unit connector M40 and rear view camera connector.
2. Turn ignition switch ON.
3. Shift the selector lever to R (reverse).
4. Check voltage between audio unit connector M40 and ground.
Is inspection result normal?
YES >> GO TO 4.
NO >> Replace audio unit. Refer to AV-113, "
Removal and Installation".
Audio unit Ground
Condition Vo l ta g e
(Approx.)
(+)
(−)
Connector Terminal
M40 50—Selector lever in R (re-
verse)
Battery Voltage
Audio unit
Rear view camera
Continuity
Connector TerminalConnector Terminal
M40 34D501 2Yes
Audio unit
GroundContinuity
Connector Terminal
M40 34 No
Audio unitGround
Condition Vo l ta g e
(Approx.)
(+)
(−)
Connector Terminal
M40 34—Selector lever is in “R”. 6.0 V
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
REAR VIEW CAMERA IMAGE SIGNAL CIRCUITAV-101
< DTC/CIRCUIT DIAGNOSIS > [DISPLAY AUDIO]
C
D
E
F
G H
I
J
K L
M B A
O P
4.CHECK CAMERA IMAGE SIGN AL CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect audio unit connector M40 and rear view camera connector.
3. Check continuity between audio unit connector M40 and rear view camera connector D501.
4. Check continuity between audio unit connector M40 and ground.
Is inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness or connectors.
5.CHECK CAMERA GROUND CIRCUIT CONTINUITY
Check continuity between audio unit connector M40 and rear view camera connector D501.
Is inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace harness or connectors.
6.CHECK CAMERA IMAGE SIGNAL
1. Connect audio unit connector M40 and rear view camera connector.
2. Turn ignition switch ON.
3. Shift the selector lever to R (reverse).
4. Check signal between audio unit connector M40 and ground.
Is inspection result normal?
YES >> Replace audio unit. Refer to AV-113, "Removal and Installation".
NO >> Replace rear view camera. Refer to AV-118, "
Removal and Installation".
Audio unit Rear view camera
Continuity
Connector TerminalConnector Terminal
M40 35D501 4Yes
Audio unit
GroundContinuity
Connector Terminal
M40 35 No
Audio unitRear view camera
Continuity
Connector TerminalConnector Terminal
M40 33D501 1Yes
Audio unit Ground
Condition Reference value
(+)
(−)
Connector Terminal
M40 35—Camera image dis-
played.
SKIB2251J
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-102
< DTC/CIRCUIT DIAGNOSIS >[DISPLAY AUDIO]
MICROPHONE SIGNAL CIRCUIT
MICROPHONE SIGNAL CIRCUIT
Diagnosis ProcedureINFOID:0000000012432971
Regarding Wiring Diagram information, refer to
AV-80, "Wiring Diagram".
1.CHECK HARNESS BETWEEN AUDIO UNIT AND MICROPHONE
1. Turn ignition switch OFF.
2. Disconnect audio unit connector M40 and microphone connector R15.
3. Check continuity between audio unit connector M40 and microphone connector R15.
4. Check continuity between audio unit connector M40 and ground.
Are continuity results as specified?
YES >> GO TO 2.
NO >> Repair harness or connectors.
2.CHECK MICROPHONE POWER SUPPLY
1. Connect audio unit connector M40 and microphone connector R15.
2. Turn ignition switch ON.
3. Check voltage between microphone connector R15 and ground.
Is the voltage reading as specified?
YES >> GO TO 3.
NO >> Replace audio unit. Refer to AV-113, "
Removal and Installation".
3.CHECK MICROPHONE SIGNAL
Check signal between terminals of audio unit connector M40.
Audio unit Microphone
Continuity
Connector TerminalConnector Terminal
M40 37
R15 1
Ye s
38 4
39 2
Audio unit
Ground Continuity
Connector Terminal
M40 37
—N o
38
Microphone Ground
Vol tag e
(Approx.)
(+)
(-)
Connector Terminal
R15 4— 5V
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-104
< DTC/CIRCUIT DIAGNOSIS >[DISPLAY AUDIO]
STEERING SWITCH
STEERING SWITCH
Diagnosis ProcedureINFOID:0000000012432972
Regarding Wiring Diagram information, refer to
AV-80, "Wiring Diagram".
1.CHECK STEERING WHEEL AUDIO CONTROL SWITCH RESISTANCE
1. Turn ignition switch OFF.
2. Disconnect combination switch connector M88.
3. Check resistance between the terminals of combination switch connector M88.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace steering switches. Refer to AV-121, "
Removal and Installation".
2.CHECK COMBINATION SWITCH
1. Disconnect combination switch connector M30.
2. Check continuity between combinat ion switch connectors M88 and M30.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace spiral cable. Refer to SR-16, "
Removal and Installation".
3.CHECK HARNESS BETWEEN AUDIO UNIT AND COMBINATION SWITCH
1. Disconnect audio unit connector M45.
2. Check continuity between audio unit connecto r M45 and combination switch connector M30.
Combination switch connector M88
ConditionResistance
Ω
(Approx.)
Te r m i n a l Te r m i n a l
14 17Depress SOURCE switch.
1
Depress switch. 121
Depress switch. 321
Depress switch. 723
15 Depress switch.
1
Depress switch. 121
Depress switch. 321
Combination switch
Continuity
Connector TerminalConnector Terminal
M88 14
M30 24
Ye s
15 31
17 33
Audio unitCombination switch
Continuity
Connector TerminalConnector Terminal
M45 6
M30 24
Ye s
16 31
15 33
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-106
< DTC/CIRCUIT DIAGNOSIS >[DISPLAY AUDIO]
USB CONNECTOR
USB CONNECTOR
Diagnosis ProcedureINFOID:0000000012432973
Regarding Wiring Diagram information, refer to
AV-80, "Wiring Diagram".
1.CHECK USB INTERFACE HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect audio unit connector M44 and USB interface connector M47.
3. Check continuity between audio unit connector M44 and USB interface connector M47.
4. Check continuity between audio unit connector M44 and ground.
Is the inspection result normal?
YES >> Replace the USB interface. Refer to AV-116, "Removal and Installation".
NO >> Repair or replace harness or connectors.
Audio unit USB interface
Continuity
Connector TerminalConnector Terminal
M44 53
M47 1
Ye s
55
3
56 4
57 5
58 6
Audio unit
—Contin u it y
Connector Terminal
M44 55
Ground No
57
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
AUXILIARY INPUT JACKAV-107
< DTC/CIRCUIT DIAGNOSIS > [DISPLAY AUDIO]
C
D
E
F
G H
I
J
K L
M B A
O P
AUXILIARY INPUT JACK
Diagnosis ProcedureINFOID:0000000012432974
Regarding Wiring Diagram information, refer to AV-80, "Wiring Diagram".
1.CHECK AUX IN JACK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect audio unit connector M56 and AUX in jack connector.
3. Check continuity between audio unit connector M56 and AUX in jack connector.
4. Check continuity between audio unit connector M56 and ground.
Is the inspection result normal?
YES >> Replace the AUX in jack. Refer to AV-117, "Removal and Installation".
NO >> Repair or replace harness or connectors.
Audio unit AUX in jack
Continuity
Connector TerminalConnector Terminal
M56 60
M46 3
Ye s
61 4
62 1
Audio unit
—Contin u it y
Connector Terminal
M56 60
Ground No
61
Revision: August 2015 2016 Versa Note

cardiagn.com

AV
NORMAL OPERATING CONDITIONAV-111
< SYMPTOM DIAGNOSIS > [DISPLAY AUDIO]
C
D
E
F
G H
I
J
K L
M B A
O P
NORMAL OPERATING CONDITION
DescriptionINFOID:0000000012432976
RELATED TO NOISE
The majority of the audio concerns are the result of outside causes (bad CD, electromagnetic interference,
etc.).
The following noise results from variations in field strength, such as fading noise and multi-path noise, or
external noise from trains and other sources. It is not a malfunction.
• Fading noise: This noise occurs because of variations in the field strength in a narrow range due to moun-
tains or buildings blocking the signal.
• Multi-path noise: This noise results from the waves sent directly from the broadcast station arriving at the antenna at a different time from the waves which reflect off mountains or buildings.
The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunctioning.
Check if noise is caused and/or changed by engine speed, ignition switch turned to each position, and opera-
tion of each piece of electrical equipment, and determine the cause.
NOTE:
The source of the noise can be found easily by listening to the noise while removing the fuses of electrical
components, one by one.
Type of Noise and Possible Cause
RELATED TO HANDS-FREE PHONE
Occurrence condition Possible cause
Occurs only when engine is ON. A continuous growling noise occurs. The speed of
the noise varies with changes in the engine speed.
• Ignition components
The occurrence of the noise is linked with the operation of the fuel pump. • Fuel pump condenser
Noise only occurs when various
electrical components are oper-
ating. A cracking or snapping sound occurs with the op-
eration of various switches.
• Relay malfunction, audio unit malfunction
The noise occurs when various motors are operat-
ing. • Motor case ground
•Motor
The noise occurs constantly, not just under certain conditions. • Rear defogger coil malfunction
• Open circuit in printed heater
• Poor ground of antenna feeder line
A cracking or snapping sound occurs while the vehicle is being driven, especially when
it is vibrating excessively. • Ground wire of body parts
• Ground due to improper part installation
• Wiring connections or a short circuit
Symptom
Cause and Counter measure
Does not recognize cellular phone connection (No connection is
displayed on the display at the guide). Some Bluetooth
® enabled cellular phones may not be recognized
by the in-vehicle phone module.
Refer to “RELATED TO HANDS-FREE PHONE (Check Compati-
bility)” in AV- 1 0 8 , "
Symptom Table".
Cannot use hands-free phone. Customer will not be able to use a hands-free phone under the fol-
lowing conditions:
• The vehicle is outside of the telephone service area.
• The vehicle is in an area where it is difficult to receive radio
waves; such as in a tunnel, in an underground parking garage,
near a tall building or in a mountainous area.
• The cellular phone is locked to prevent it from being dialed.
NOTE:
While a cellular phone is connected through the Bluetooth
® wire-
less connection, the battery power of the cellular phone may dis-
charge quicker than usual. The Bluetooth
® Hands-Free Phone
System cannot charge cellular phones.
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-126
< PRECAUTION >[NAVIGATION]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint Syst
em (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000012432992
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harn esses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electri c power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Cautions in Removing Battery Terminal and AV Control Unit (Models with AV Control
Unit)
INFOID:0000000012432993
CAUTION:
Remove battery terminal and AV control unit 30 seconds or more after turning the ignition switch OFF.
NOTE:
After the ignition switch is turned OFF, the AV cont rol unit continues operating for approximately 30 seconds.
Therefore, data corruption may occur if battery voltage is cut off within 30 seconds.
Precaution for Trouble DiagnosisINFOID:0000000012432994
AV COMMUNICATION SYSTEM
• Do not apply voltage of 7.0 V or higher to the measurement terminals.
• Use the tester with its open terminal voltage being 7.0 V or less.
• Be sure to turn ignition switch OFF and disconnect the battery cable from\
the negative terminal before checking the circuit.
Precaution for Harness RepairINFOID:0000000012432995
AV COMMUNICATION SYSTEM
Revision: August 2015 2016 Versa Note

cardiagn.com

AV-144
< SYSTEM DESCRIPTION >[NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
3. While pressing the APPS button, turn the TUNE dial counter-
clockwise 5 or more clicks, then clockwise 5 or more clicks, then
counterclockwise 5 or more clicks. Shifting from current screen
to previous screen is performed by pressing BACK button.
4. The trouble diagnosis initial screen is displayed, and Version, User Configuration, Radio, Syst em State or Self Test can be
selected.
CONSULT FunctionINFOID:0000000012433016
CONSULT FUNCTIONS
CONSULT performs the following functions via communication with the AV control unit.
ECU IDENTIFICATION
The part number of AV control unit is displayed.
SELF DIAGNOSTIC RESULT
Refer to AV-151, "DTC Index".
DATA MONITOR
CONFIGURATION
Refer to AV-175, "CONFIGURATION (AV CONTROL UNIT) : Description".
CAN DIAG SUPPORT MNTR
AWNIA3744ZZ
AWNIA3745ZZ
Direct Diagnostic Mode Description
ECU Identification The AV control unit part number is displayed.
Self Diagnostic Result The AV control unit self diagnostic results are displayed.
Data Monitor The AV control unit input/output data is displayed in real time.
Configuration • The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing AV control unit.
CAN Diag Support Mntr • The result of transmit/receive diagnosis of AV communication is displayed.
• The result of transmit/receive diagnosis of CAN communication is displayed.
Monitor Item [Unit]
Description
VHCL SPD SIG [On/Off] Indicates vehicle speed signal received from combination meter on CAN communication
line.
ILLUM SIG [On/Off] Indicates condition of illumination signal for the AV control unit.
IGN SIG [On/Off] Indicates condition of ignition signal.
REV SIG [On/Off] Indicates condition of reverse signal received from transmission range switch (with CVT)
or park/neutral position (PNP) switch (back-up) (with M/T).
Revision: August 2015
2016 Versa Note

cardiagn.com

AV-148
< ECU DIAGNOSIS INFORMATION >[NAVIGATION]
AV CONTROL UNIT
ECU DIAGNOSIS INFORMATION
AV CONTROL UNIT
Reference ValueINFOID:0000000012433018
VALUES ON THE DIAGNOSIS TOOL
TERMINAL LAYOUT
PHYSICAL VALUES
Monitor Item
ConditionValue/Status
VHCL SPD SIG Vehicle speed = 0 km/h (0 MPH).
Off
Vehicle speed > 0 km/h (0 MPH). On
ILLUM SIG Illumination signal is not received.
Off
Illumination signal is received. On
IGN SIG Ignition switch OFF or ACC.
Off
Ignition switch ON. On
REV SIG Selector lever in any position other than R.
Off
Selector lever in R position. On
AWNIA3655ZZ
Te r m i n a l
(Wire color) Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output Ignition
switch Operation
2
(GR) 3
(P) Sound signal front speaker
LH
Output ON Sound output
4
(W) 5
(R) Sound signal rear speaker
LH
Output ON Sound output
SKIB3609E
SKIB3609E
Revision: August 2015
2016 Versa Note

cardiagn.com