seats NISSAN NOTE 2016 Service Service Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2016, Model line: NOTE, Model: NISSAN NOTE 2016Pages: 3641, PDF Size: 28.72 MB
Page 2824 of 3641

SQUEAK AND RATTLE TROUBLE DIAGNOSESSE-11
< SYMPTOM DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
1. Loose harness or harness connectors.
2. Front console map/reading lamp lens loose.
3. Loose screws at console attachment points.
SEATS
When isolating seat noise it's important to note the position the seat is in and the load placed on the seat when
the noise is present. These conditions should be duplicated when verifying and isolating the cause of the
noise.
Cause of seat noise include:
1. Headrest rods and holder
2. A squeak between the seat pad cushion and frame
3. The rear seatback lock and bracket
These noises can be isolated by moving or pressing on the suspected components while duplicating the con-
ditions under which the noise occurs. Most of thes e incidents can be repaired by repositioning the component
or applying urethane tape to the contact area.
UNDERHOOD
Some interior noise may be caused by components under the hood or on the engine wall. The noise is then
transmitted into the passenger compartment.
Causes of transmitted underhood noise include:
1. Any component installed to the engine wall
2. Components that pass through the engine wall
3. Engine wall mounts and connectors
4. Loose radiator installation pins
5. Hood bumpers out of adjustment
6. Hood striker out of adjustment
These noises can be difficult to isolate since they cannot be reached from the interior of the vehicle. The best
method is to secure, move or insulate one component at a time and test drive the vehicle. Also, engine rpm or
load can be changed to isolate the noise. Repairs can usually be made by moving, adjusting, securing, or
insulating the component causing the noise.
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2832 of 3641

FRONT SEATSE-19
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
DRIVER SEAT WITHOUT LIFT AND ARMREST
1. Armrest 2. Seat cushion outer finisher (RH) 3. Seat belt buckle
4. Seat cushion outer finisher (LH) 5. Lift lever 6. Lift lever cap
7. Recline lever 8. Headrest holder (locked) 9. Headrest holder (free)
10. Headrest 11. Seat assembly
AWJIA1998ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2834 of 3641

FRONT SEATSE-21
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
PASSENGER SIDE : Exploded ViewINFOID:0000000012829361
AWJIA1999ZZ
1. Headrest 2. Headrest holder (free) 3. Headrest holder (locked)
4. Seat assembly 5. Recline lever 6. Seat cushion outer finisher
(RH)
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2836 of 3641

REAR SEATSE-23
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
REAR SEAT
Exploded ViewINFOID:0000000012432041
REAR SEAT WITH ARMREST
AWJIA1138ZZ
1. Seatback hinge trim 2. Seatback hinge 3. Seatback striker
4. Headrest 5. Seatback (RH) 6. Headrest holder (locked)
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2838 of 3641

REAR SEATSE-25
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
REAR SEAT WITHOUT ARMREST
AWJIA1137ZZ
1. Seatback hinge trim 2. Seatback hinge 3. Seatback striker
4. Headrest 5. Seatback(RH) 6. Headrest holder (locked)
7. Headrest holder (free) 8. Seatback latch bracket (RH) 9. Seatback latch (RH)
10. Seatback frame (RH) 11. Seatback latch finisher (RH) 12. Seatback latch release knob
13. Seatback trim (RH) 14. Seatback pad (RH) 15. Seat cushion hook
16. Seat cushion 17. Seat cushion pad 18. Seat cushion trim
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2840 of 3641

REAR SEATSE-27
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
Seatback (RH)
1. Place the seatback (RH) in the folded down position.
2. Release hook fasteners (A).
3. Remove bolts (B) and the seatback (RH) (1).
INSTALLATION
Installation is in the reverse order of removal.
Tighten the seatback assembly bolts to specification. Refer to
SE-23, "
Exploded View".
SEATBACK HINGE
SEATBACK HINGE : Removal and InstallationINFOID:0000000012432044
REMOVAL
1. Remove the seatbacks (LH/RH). Refer to SE-26, "SEATBACK : Removal and Installation".
2. Remove the seat cushion. Refer to SE-26, "
SEAT CUSHION : Removal and Installation"
3. Remove bolts (A) and the seatback hinge (1).
INSTALLATION
Installation is in the reverse order of removal.
Tighten the seatback hinge assembly bolts to specification. Refer to SE-23, "
Exploded View".
SEATBACK STRIKER
SEATBACK STRIKER : Removal and InstallationINFOID:0000000012432045
REMOVAL
1. Remove the luggage side upper finisher. Refer to INT-35, "LUGGAGE SIDE UPPER FINISHER :
Removal and Installation".
2. Remove bolts and the seatback strikers.
INSTALLATION
Installation is in the reverse order of removal.
Tighten the seatback striker bolts to specification. Refer to SE-23, "
Exploded View".
SEAT CUSHION HOOK
SEAT CUSHION HOOK : Removal and InstallationINFOID:0000000012432046
REMOVAL
ALJIA1243ZZ
ALJIA1244ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2844 of 3641

FRONT SEATSE-31
< UNIT DISASSEMBLY AND ASSEMBLY >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
DRIVER SEAT WITHOUT LIFT AND ARMREST
1. Armrest 2. Seat cushion outer finisher (RH) 3. Seat belt buckle
4. Seat cushion outer finisher (LH) 5. Lift lever 6. Lift lever cap
7. Recline lever 8. Headrest holder (locked) 9. Headrest holder (free)
10. Headrest 11. Seat assembly
AWJIA1998ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2846 of 3641

FRONT SEATSE-33
< UNIT DISASSEMBLY AND ASSEMBLY >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
ASSEMBLY
Assembly is in the reverse order of disassembly.
Smooth out all wrinkles during assembly.
DRIVER SIDE : Seat CushionINFOID:0000000012834456
DISASSEMBLY
1. Remove the drive side front seat. Refer to SE-20, "DRIVER SIDE : Removal and Installation".
2. Remove the recline lever (1).
3. Pull to release pawls and remove the lift lever cap (1) (if equipped).
4. Remove the lift lever screws (A) and remove lift lever (1) (if equipped).
5. Remove the seat cushion outer finisher (LH) (1).
a. Pull to release clips and pawls in the direction ( ) shown and remove.
6. Remove the seat belt buckle (LH). Refer to SB-8, "
FRONT SEAT BELT BUCKLE : Removal and Installa-
tion".
ALJIA1855ZZ
: Pawl
ALJIA1856ZZ
ALJIA1857ZZ
: Pawl
: Clip
ALJIA1858ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2848 of 3641

FRONT SEATSE-35
< UNIT DISASSEMBLY AND ASSEMBLY >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
PASSENGER SIDE : Exploded ViewINFOID:0000000012432051
AWJIA1999ZZ
1. Headrest 2. Headrest holder (free) 3. Headrest holder (locked)
4. Seat assembly 5. Recline lever 6. Seat cushion outer finisher
(RH)
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 2850 of 3641

FRONT SEATSE-37
< UNIT DISASSEMBLY AND ASSEMBLY >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
2. Remove recline lever (1).
3. Release clips and pawls using suitable tool and remove the seat cushion outer finisher (RH) (1).
4. Remove seat belt buckle (RH). Refer to SB-8, "
FRONT SEAT BELT BUCKLE : Removal and Installation".
5. Release the clips and pawls using a suitable tool and remove the seat cushion outer finisher (LH) (1).
ASSEMBLY
Assembly is in the reverse order of disassembly.
Smooth out all wrinkles during assembly.
ALJIA1852ZZ
: Pawl
: Clip
ALJIA1853ZZ
: Pawl
: Clip
ALJIA1854ZZ
Revision: August 2015 2016 Versa Note
cardiagn.com