oil level NISSAN PATHFINDER 2004 R50 / 2.G Owners Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2004, Model line: PATHFINDER, Model: NISSAN PATHFINDER 2004 R50 / 2.GPages: 306, PDF Size: 3.41 MB
Page 71 of 306
4H or 4LO position again to turn off the ATP
warning light when the warning light comes on.
(Before shifting the 4WD shift switch into the
4LO position or out of 4LO into the 4H position,
move the automatic transmission selector lever
into the N position). Shift the selector lever into
the P position and make sure that the 4WD shift
indicator light is ON and the ATP warning light is
OFF.
or
Brake warning light
This light functions for both the parking brake
and the foot brake systems.
Parking brake indicator:
The light comes on when the parking brake is
applied.
Low brake fluid warning light:
When the ignition key is in the ON position, the
light warns of a low brake fluid level. If the light
comes on while the engine is running, stop the
vehicle and perform the following:
1. Check the brake fluid level. Add brake fluid as
necessary. See “Brake and clutch fluid” in the
“8. Maintenance and do-it-yourself” section.
2. If the brake fluid level is correct:
Have the warning system checked by a NISSAN
dealer.
WARNING
Your brake system may not be work-
ing properly if the warning light is on.
Driving could be dangerous. If you
judge it to be safe, drive carefully to
the nearest service station for re-
pairs. Otherwise, have your vehicle
towed.
Pressing the brake pedal with the
engine stopped and/or low brake
fluid level may increase your stop-
ping distance and braking will re-
quire greater pedal effort as well as
greater pedal travel.
If the brake fluid level is below the
MINmark on the brake fluid reser-
voir, do not drive until the brake sys-
tem has been checked at a NISSAN
dealer.
Charge warning light
If the light comes on while the engine is running,
it may indicate the charging system is not func-
tioning properly. Turn the engine off and checkthe alternator belt. If the belt is loose, broken,
missing or if the light remains on, see your
NISSAN dealer immediately.
CAUTION
Do not continue driving if the belt is
loose, broken or missing.
Door open warning light
This light comes on when any of the doors
and/or rear window are not closed securely
while the ignition key is ON.
Engine oil pressure warning
light
This light warns of low engine oil pressure. If the
light flickers or comes on during normal driving,
pull off the road in a safe area, stop the engine
immediatelyand call a NISSAN dealer or other
authorized repair shop.
The oil pressure warning light is not de-
signed to indicate a low oil level. Use the
dipstick to check the oil level.See “Engine
oil” in the “8. Maintenance and do-it-yourself”
section.
Instruments and controls
2-11
04.3.9/R50-D/V5
Page 172 of 306
Make sure the area around the vehicle is
clear.
Check fluid levels such as engine oil, coolant,
brake and clutch fluid, window washer fluid
as frequently as possible, at least whenever
you refuel.
Check to be sure that all windows and light
lenses are clean.
Visually inspect tires for their appearance and
condition. Also check tires for proper infla-
tion.
Lock all doors.
Position seat and adjust head restraints.
Adjust inside and outside mirrors.
Fasten seat belts and ask all passengers to
do likewise.
Check the operation of warning lights when
key is turned to the ON (3) position.1. Apply the parking brake.
2.Automatic transmission:
Move the selector lever to P (Park position) or
N (Neutral position). (P preferred)
The selector lever cannot be moved out
of P and into any of the other gear
positions if the ignition key is turned to
LOCK or if the key is removed from the
switch.
The starter is designed not to operate if
the selector lever is in one of the driving
positions.
Manual transmission:
Move the gearshift lever to N (Neutral posi-
tion), and depress the clutch pedal to the
floor while starting the engine.
The starter is designed not to operate
unless the clutch pedal is fully de-
pressed.
3. Crank the enginewith your foot off the
accelerator pedalby turning the ignition
key to START. Release the key when the
engine starts. If the engine starts, but fails to
run, repeat the above procedure.
If the engine is very hard to start in extremely
cold weather or when restarting, depress theaccelerator pedal a little (approximately 1/3
to the floor) and hold it then crank the engine.
Release the key and the accelerator pedal
when the engine starts.
If the engine is very hard to start because it is
flooded, depress the accelerator pedal all the
way to the floor and hold it. Crank the engine
for 5 to 6 seconds. After cranking the engine,
release the accelerator pedal. Crank the en-
ginewith your foot off the accelerator
pedalby turning the ignition key to START.
Release the key when the engine starts. If the
engine starts, but fails to run, repeat the
above procedure.
CAUTION
Do not operate the starter for more than
15 seconds at a time. If the engine does
not start, turn the key off and wait 10
seconds before cranking again, other-
wise the starter could be damaged.
4.Warm-up
Always allow the engine to idle for at least 30
seconds after starting. Do not race the en-
gine while warming it up. Drive at moderate
speed for a short distance first, especially in
BEFORE STARTING THE ENGINE STARTING THE ENGINE5-10
Starting and driving
04.3.9/R50-D/V5
Page 227 of 306
8 Maintenance and do-it-yourselfMaintenance requirements .................................................. 8-2
General maintenance ............................................................ 8-2
Explanation of general maintenance items ................ 8-2
Maintenance precautions ..................................................... 8-5
Engine compartment check locations .............................. 8-7
Engine cooling system.......................................................... 8-8
Checking engine coolant level...................................... 8-8
Changing engine coolant ............................................... 8-9
Engine oil ............................................................................... 8-11
Checking engine oil level ............................................ 8-11
Changing engine oil ...................................................... 8-12
Changing engine oil filter ............................................ 8-13
Automatic transmission fluid ............................................. 8-14
Temperature conditions for checking ....................... 8-14
Power steering fluid ............................................................ 8-15
Brake and clutch fluid ........................................................ 8-16
Brake fluid ....................................................................... 8-16
Clutch fluid ...................................................................... 8-16
Window washer fluid.......................................................... 8-17
Window washer fluid reservoir .................................. 8-17
Battery .................................................................................... 8-18
Jump starting .................................................................. 8-18
Drive belts ............................................................................. 8-19
Spark plugs ........................................................................... 8-20Replacing spark plugs.................................................. 8-20
Air cleaner ............................................................................. 8-20
Windshield wiper blades ................................................... 8-21
Cleaning ........................................................................... 8-21
Replacing ......................................................................... 8-21
Parking brake and brake pedal ........................................ 8-22
Checking parking brake ............................................... 8-22
Checking brake pedal .................................................. 8-23
Brake booster ................................................................. 8-23
Fuses ...................................................................................... 8-24
Engine compartment ..................................................... 8-24
Passenger compartment .............................................. 8-25
Keyfobbattery replacement ........................................ 8-25
Lights ...................................................................................... 8-27
Headlights ....................................................................... 8-28
Wheels and tires ................................................................. 8-31
Tire pressure ................................................................... 8-31
Tire labeling ..................................................................... 8-34
Types of tires .................................................................. 8-36
Tire chains ....................................................................... 8-36
Changing wheels and tires ......................................... 8-37
04.3.9/R50-D/V5
Page 230 of 306
operate smoothly and that all latches lock se-
curely in every position. Check that the head
restraints move up and down smoothly and that
the locks (if so equipped) hold securely in all
latched positions.
Seat belts:
Check that all parts of the seat belt system (e.g.
buckles, anchors, adjusters and retractors) op-
erate properly and smoothly, and are installed
securely. Check the belt webbing for cuts, fray-
ing, wear or damage.
Steering wheel:
Check for changes in the steering conditions,
such as excessive freeplay, hard steering or
strange noises.
Warning lights and chimes:
Make sure that all warning lights and chimes are
operating properly.
Windshield defroster:
Check that the air comes out of the defroster
outlets properly and in sufficient quantity when
operating the heater or air conditioner.
Windshield wiper and washer*:
Check that the wipers and washer operate
properly and that the wipers do not streak.
Under the hood and vehicleThe maintenance items listed here should be
checked periodically e.g. each time you check
the engine oil or refuel.
Automatic transmission fluid level*:
Check the level after putting the selector lever in
P (Park) with the engine idling.
Battery*:
Check the fluid level in each cell. It should be
between the MAX and MIN lines.
Vehicles operated in high temperatures or under
severe conditions require frequent checks of the
battery fluid level.
Brake and clutch fluid levels*:
Make sure that the brake and clutch fluid level is
between the MAX and MIN lines on the reservoir.
Engine coolant level*:
Check the coolant level when the engine is cold.
Engine drive belts*:
Make sure that no belt is frayed, worn, cracked
or oily.
Engine oil level*:
Check the level after parking the vehicle on alevel spot and turning off the engine. (Be sure to
wait a few minutes to allow the oil to drain back
into the sump.)
Exhaust system:
Make sure there are no loose supports, cracks or
holes. If the sound of the exhaust seems unusual
or there is a smell of exhaust fumes, immediately
locate the trouble and correct it. See “Precau-
tions when starting and driving” in the “5. Start-
ing and driving” section for exhaust gas (carbon
monoxide).
Fluid leaks:
Check under the vehicle for fuel, oil, water or
other fluid leaks after the vehicle has been
parked for a while. Water dripping from the air
conditioner after use is normal. If you should
notice any leaks or if gasoline fumes are evident,
check for the cause and have it corrected imme-
diately.
Power steering fluid level* and lines:
Check the level when the fluid is cold and the
engine is turned off. Check the lines for proper
attachment, leaks, cracks, etc.
Radiator and hoses:
Check the front of the radiator and clean off any
dirt, insects, leaves, etc., that may have accumu-
lated. Make sure the hoses have no cracks,
8-4
Maintenance and do-it-yourself
04.3.9/R50-D/V5
Page 237 of 306
3. Open the air release plug(s) to drain the
coolant.
4. Flush the cooling system by running fresh
water through the radiator.
Waste coolant must be disposed of
properly.
Check your local regulations.
5. Close the radiator drain plugs and engine
block drain plugs securely.
6. See the “9. Technical and consumer informa-
tion” section for cooling system capacity.
Fill the radiator slowly with the proper mixture
of coolant and water. Fill the reservoir tank
slowly up to the MAX level. Then install the
radiator cap and close the air release plug(s).
7. Start the engine and warm it up until it
reaches normal operating temperature. Then
race the engine 2 or 3 times under no load.
Watch the coolant temperature gauge for
signs of overheating.
8. Stop the engine. After it completely cools
down, refill the radiator up to the filler open-
ing. Fill the reservoir tank up the MAX level.
9. Check the radiator drain plug and engine
block drain plugs for any sign of leakage.
CHECKING ENGINE OIL LEVEL1. Park the vehicle on a level surface and apply
the parking brake.
2. Run the engine until it reaches operating
temperature.
3. Turn off the engine.Wait more than 10
minutes for the oil to drain back into the
oil pan.
4. Remove the dipstick and wipe it clean. Rein-
sert it all the way.
5. Remove the dipstick again and check the oil
level. It should be between the H and L
marks. If the oil level is below the L mark,remove the oil filler cap and pour recom-
mended oil through the opening. Do not
overfill.
6. Recheck oil level with dipstick.
It is normal to add some oil between oil
changes or during the break-in period, de-
pending on the severity of operating con-
ditions.
CAUTION
Oil level should be checked regularly.
SDI1114
SDI1141
ENGINE OIL
Maintenance and do-it-yourself
8-11
04.3.9/R50-D/V5
Page 238 of 306
Operating with insufficient amount of
oil can damage the engine, and such
damage is not covered by warranty.
CHANGING ENGINE OIL1. Park the vehicle on a level surface and apply
the parking brake.
2. Warm up the engine until it reaches operat-
ing temperature, and then turn it off and wait
more than 10 minutes.
3. Place a large drain pan under the drain plug.
4. Remove the oil filler cap.
5. Remove the drain plug with a wrench and
completely drain the oil.
If the oil filter is to be changed, remove and
replace it at this time. See later in this sectionfor changing engine oil filter.
CAUTION
Be careful not to burn yourself, as the
engine oil is hot.
Waste oil must be disposed of prop-
erly.
Check your local regulations.
6. Clean and re-install the drain plug and new
washer. Securely tighten the drain plug with a
wrench. Do not use excessive force.
Drain plug tightening torque:
22 to 29 ft-lb (29 to 39 N⋅m)
7. Refill engine with recommended oil through
the oil filler opening, then install the oil filler
cap securely.
See “Capacities and recommended
fuel/lubricants” in the “9. Technical and con-
sumer information” section for drain and refill
capacity.
The drain and refill capacity depends on the
oil temperature and drain time. Use these
specifications for reference only. Always use
the dipstick to determine when the proper
SDI1594
8-12
Maintenance and do-it-yourself
04.3.9/R50-D/V5
Page 239 of 306
amount of oil is in the engine.
8. Start the engine.
Check for leakage around the drain plug.
Correct as required.
9. Turn the engine off and wait more than 10
minutes. Check the oil level with the dipstick.
Add engine oil if necessary.
WARNING
Prolonged and repeated contact with
used engine oil may cause skin can-
cer.
Try to avoid direct skin contact with
used oil. If skin contact is made,
wash thoroughly with soap or hand
cleaner as soon as possible.
Keep used engine oil out of reach of
children.
CHANGING ENGINE OIL FILTER1. Park the vehicle on a level surface and apply
the parking brake.
2. Turn the engine off.
3. Loosen the oil filter with an oil filter wrench.
(Depending on the engine model, a special
cap-type wrench may be required. See your
NISSAN dealer.) Then remove the oil filter by
turning it by hand.
CAUTION
Be careful not to burn yourself, as the
engine oil may be hot.
4. Wipe the engine oil filter mounting surface
with a clean rag.
Be sure to remove any old rubber gasket
remaining on the mounting surface of the
engine.
5. Coat the rubber gasket on the new filter with
engine oil.
6. Screw in the oil filter until a slight resistance
is felt, then tighten an additional 2/3 turn.
Oil filter tightening torque:
10.85 to 15.12 ft-lb
(14.7 to 20.5 N⋅m)
7. Start the engine and check for leakage
around the oil filter. Correct as required.
8. Turn the engine off and wait several minutes.
Check the oil level. Add engine oil if neces-
sary.
SDI1113
Maintenance and do-it-yourself
8-13
04.3.9/R50-D/V5
Page 245 of 306
under severe conditions require frequent
checks of the battery fluid level.
WARNING
Be sure the ignition key is in the OFF or
LOCK position. The engine could rotate
unexpectedly.
1. Visually inspect each belt for signs of unusual
wear, cuts, fraying oil adhesion or looseness.
If the belt is in poor condition or loose, have
it replaced or adjusted by your NISSAN
dealer.
2. Have the belts checked regularly for condi-tion and tension.
SDI1480
SDI1119
DRIVE BELTS
Maintenance and do-it-yourself
8-19
04.3.9/R50-D/V5
Page 269 of 306
Capacity (Approximate)
Recommended specifications
US
measureImp
measureLiter
Manual transmission— — — API GL-4 Viscosity SAE 75W-85
Differential gear oil (exc. LSD)— — — API GL-5 Viscosity SAE 80W-90*1
Limited-slip differential (LSD) gear oil — — —Only LSD gear oil:
API GL-5 and SAE 80W-90*1 approved for Nissan LSD*2
Automatic transmission fluid
Refill to the proper oil level according to the instructions
in the “8. Maintenance and do-it-yourself” section.Nissan Matic “D” (Continental U.S. and Alaska) or Canada NISSAN
Automatic Transmission Fluid.*6
Power steering fluid (PSF)Genuine NISSAN PSF or equivalent*5
All-mode 4WD transfer fluidNissan Matic “D” (Continental U.S. and Alaska) or Canada NISSAN
Automatic Transmission Fluid.*6
Transfer fluidNissan Matic “D” (Continental U.S. and Alaska) or Canada NISSAN
Automatic Transmission Fluid.*6 or API GL-4 Viscosity SAE 75W-90
Brake and clutch fluidGenuine Nissan Super Heavy Duty Brake Fluid*4 or equivalent
DOT 3 (U.S. F.M.V.S.S. No. 116)
Propeller shaft grease— — — NLGI No. 2 (Lithium soap base)
Multi-purpose grease— — — NLGI No. 2 (Lithium soap base)
Air conditioning system refrigerant— — — HFC-134a (R-134a)*4
Air conditioning system lubricants———Nissan A/C System Oil Type S or exact equivalent*4
*1: For hot areas, viscosity SAE 90 is suitable for ambient temperatures above 0°C (32°F).
*2: Contact your NISSAN dealer for a list of approved oils.
*3: Available in mainland U.S. through your NISSAN dealer.
*4: See “Vehicle identification” later in this section for air conditioner specification label.
*5: For Canada, NISSAN Automatic Transmission Fluid (ATF), DEXRON
TMIII/MERCON
TMor equivalent ATF may also be used.
*6: Dexron
TMIII/Mercon
TM
or equivalent may also be used. Outside the continental U.S. and Alaska contact an authorized NISSAN dealer for more information regarding
suitable fluids, including recommended brand(s) of DEXRON
TMIII/MERCON
TMAutomatic Transmission Fluid.
Technical and consumer information
9-3
04.3.9/R50-D/V5
Page 298 of 306
Seat belt warning light and chime ................. 2-13
Cigarette lighter and ashtray .................................. 2-29
Circuit breaker, Fusible link .................................... 8-24
Cleaning exterior and interior .......................... 7-2, 7-3
Clock ............................................................................ 2-28
Clutch fluid.................................................................. 8-16
Coin box ...................................................................... 2-30
Cold weather driving ................................................ 5-37
Compact Disc (CD) changer operation .............. 4-26
Compact Disc (CD) player (See audio
system) ......................................................................... 4-19
Compact spare tire ................................................... 8-39
Compass display ......................................................... 2-7
Console box................................................................ 2-34
Controls
Heater and air conditioner controls.................. 4-2
Steering wheel audio controls ........................ 4-28
Coolant
Capacities and recommended fuel/
lubricants ................................................................. 9-2
Changing engine coolant .................................... 8-9
Checking engine coolant level........................... 8-8
Corrosion protection ................................................... 7-4
Cover, Tonneau cover .............................................. 2-37
Cruise control............................................................. 5-18
Cup holders ................................................................ 2-32
CVT, Transmission selector lever lock
release .......................................................................... 5-14
D
Daytime running light system ................................. 2-24
Dimensions and weights ......................................... 9-11
Door open warning light .......................................... 2-11Drive belts ................................................................... 8-19
Drive positioner, Automatic..................................... 3-17
Driving
All-mode four wheel drive (4WD) .................. 5-25
Cold weather driving ......................................... 5-37
Driving with automatic transmission ..... 5-7, 5-11
Driving with manual transmission .......... 5-8, 5-16
On-pavement and offroad driving ..................... 5-4
Part time four wheel drive (4WD) .................. 5-21
Precautions when starting and driving ............ 5-2
Safety precautions ................................................ 5-5
E
Economy, Fuel............................................................ 5-20
Electric sunroof .......................................................... 2-40
Emission control information label ........................ 9-13
Emission control system warranty......................... 9-24
Engine
Before starting the engine................................ 5-10
Break-in schedule............................................... 5-20
Capacities and recommended fuel/
lubricants ................................................................. 9-2
Changing engine coolant .................................... 8-9
Changing engine oil ........................................... 8-12
Changing engine oil filter ................................. 8-13
Checking engine coolant level........................... 8-8
Checking engine oil level ................................. 8-11
Coolant temperature gauge ............................... 2-4
Engine block heater ........................................... 5-39
Engine compartment check locations.............. 8-7
Engine cooling system ......................................... 8-8
Engine oil .............................................................. 8-11
Engine oil and oil filter recommendation......... 9-6Engine oil viscosity ............................................... 9-6
Engine serial number ......................................... 9-13
Engine specifications ........................................... 9-9
If your vehicle overheats ................................... 6-11
Starting the engine............................................. 5-10
Event data recorders ................................................ 9-26
Exhaust gas (Carbon monoxide).............................. 5-2
F
F.M.V.S.S. certification label................................... 9-13
Filter
Air cleaner housing filter ................................... 8-20
Changing engine oil filter ................................. 8-13
Flashers (See hazard warning flasher switch) ... 2-25
Flat tire............................................................................ 6-2
Flat tire, Low tire pressure warning system .......... 5-3
Flat towing .................................................................. 9-22
Floor mat cleaning ....................................................... 7-4
Fluid
Automatic transmission fluid (ATF) ................ 8-14
Brake and clutch fluid ....................................... 8-16
Brake fluid............................................................. 8-16
Capacities and recommended fuel/
lubricants ................................................................. 9-2
Engine coolant ....................................................... 8-8
Engine oil .............................................................. 8-11
Power steering fluid ........................................... 8-15
Window washer fluid ......................................... 8-17
FM-AM radio with cassette player and Compact
Disc (CD) player........................................................ 4-16
FM-AM-SATELLITE radio with cassette
player and Compact Disc (CD) player/CD
changer ........................................................................ 4-23
04.3.9/R50-D/V5
10-2