NISSAN PATHFINDER 2007 R51 / 3.G Quick Reference Guide

REMOTE KEYLESS ENTRY SYSTEM
LOCK DOORS
Press the LPD0150 button once to lock all doors and the
fuel-filler door.
UNLOCK DOORS
Press the
lpd0151
button once to unlock the driver’s door and the fuel-filler door. Press the button again within 5 seconds to unlock all doors.
U SING THE PANIC ALARM
Press and hold the button for longer than 0.5 seconds. The panic alarm will sound and the headlights will stay on for 25 seconds. The panic alarm stops when it has run for 25 seconds or when any button is pressed on the keyfob.
SILENCING THE HORN BEEP FEATURE
For vehicles without Navigation system: To deactivate: Press and hold the LPD0150 and
lpd0151
buttons for at least 2 seconds.
 To activate: Press and hold the LPD0150 and
lpd0151
buttons for at least 2 seconds.
For vehicles with Navigation system:
 Refer to the “Display screen, heater, air conditioner and audio systems” section in your Owner’s Manual for the procedure.
Note: If you change the horn beep feature with the keyfob, the display screen will not show the current mode and cannot be used to change the mode. Use the keyfob to return to the previous mode and re-enable the display screen control.
 A keyfob can be linked to each memory button.
 If memory positioning is reset to a new location, the keyfob automatically re-links.
RECALLING A MEMORY SET TING FROM THE MEMORY PAD Set the automatic transmission lever to the P ( Park) position, then: Within 45 seconds of opening the driver’s door, push the memory switch (1 or 2) fully for at least 1 second, or Turn the ignition switch to the ON position and push the memory switch (1 or 2) fully for at least 1 second.
FROM THE KEYFOB If properly linked, operation of the
lpd0151
button will automatically return the driver’s seat, accelerator and brake pedals, and outside mirrors to the memorized position.
ENTRY/ EXIT FUNCTION
The driver’s seat moves to allow the driver to get into and out of the driver’s seat more easily. The driver’s seat slides backward when:
 The key is removed from the ignition switch.
 The driver’s door is opened with the key turned to LOCK.
 The key is turned from ACC to LOCK with the driver’s door open and the automatic transmission lever is in the P ( Park) position.
The driver’s seat returns to the previous position when:
 The key is inserted into the ignition switch.
 The driver’s door is closed with the key turned to LOCK.
 The key is turned from ACC to ON while the automatic transmission lever is in the P
( Park) position.

Pedal P osition adJust Ment (if so equipped)
The accelerator and brake pedals can be adjusted for your driving comfort.
 Adjust the pedals when the automatic transmission selector lever is in P ( Park).
 Push 01 to move the position of the pedals forward.  Push 02 to move the position of the pedals backward.02
01
tri P co MP uter (if so equipped)
The trip computer readout is in the speedometer display. It can show the following items:
 TRIP “A” – Measures the distance of one specific trip.
 TRIP “B” – Measures the distance of a second specific trip.
 DISTANCE TO EMPT Y (dte) – Estimates the distance that can be driven before refueling.
 AVER AGE SPEED – (mph or km /h) Shows the average speed since the last reset.
 AVER AGE FUEL CONSUMPTION – (mpg or l /100km) Shows the average fuel consumption since the last reset.
 JOURNEY TIME – Shows the time since the last reset.
 RESET – Press the CHANGE button on the instrument panel for more than 1 second to reset the trip odometer to zero.
With the ignition key in the ON position or the vehicle running, you can select an item by pressing the CHANGE button on the instrument panel.
instru Ment Brightness control /tri P change
B utton
The instrument brightness control operates when the headlight control switch is in the or position.
Turn the control to adjust the brightness of the instrument panel lights.
Press the change button to select trip computer features. See above for more information on the trip computer.
front seat ad Just Ments
With manual seats (passenger’s side, if so equipped):
 Pull up on the lever under the front of the seat and slide backward or forward; release.
 Lift the lever on the side of the seat to adjust your seatback backward or forward; release when you have found a comfortable
angle and the seat belt fits properly.
With power seats (if so equipped):
 Move the control 01 forward or backward to adjust the seat cushion forward or backward.
 Pull up 01 to raise the seat cushion; press down to lower the cushion.
0102

 Push the switch 02 forward to move the seatback forward; push it back to move the seatback backward.
LUMBAR SUPPORT (if so equipped) Your driver’s seat has a lumbar support; adjust it by moving the lever
03 up or down.
03
folding the 3rd row seats
 Pull up on the latches 01 located in the outer corners of each seatback and fold the seatbacks forward over the seat base.
 To return the 3rd row seats to a seating position use the pull straps 02 to raise each seatback. Pull back until the seatback latches into position.
Make sure to properly raise each seatback to an upright and
secured position.
folding the 2nd row Bench seat
To fold the 2nd row bench seat flat for maximum cargo hauling:
 Lower the head restraint to the “down” position.
 Pull the strap 01 located in the center of the seat cushion toward the front of the vehicle.  Lift up on the recline lever 02 to fold the seatback forward.
 Fold the carpet panel flap 03 toward the back of the vehicle. (The carpet panel flap provides a level cargo floor when the 3rd row seats are also folded flat.)
 Reverse this process to return the 2nd row bench seats to a seating position.
Make sure to properly raise the seatback to an upright position and push the seat cushion down into place.
01
02
03
01
02
ti P uP for eas Y entr Y or exit fro M the 3rd
row
The 2nd row outboard seats can be tipped forward for easy entry or exit from the 3rd row bench seat.
 To enter the 3rd row, lift up on the latch located on the upper corner of the seatback 01 on the back of the 2nd row outboard seats.
 This will then release the back of the seat and tip the 2nd row outboard seat forward. 02
 To exit the 3rd row bench seat, lift up on the same latch and tip the seatback forward.
01
02

This easy-to-use Quick Reference Guide is intended to help you more fully appreciate some of the unique features and functions of your new vehicle. However, it is not intended to replace your Owner’s Manual. The Owner’s Manual contains more detailed information to help you better understand the important safety warnings, features, operation, and maintenance of your vehicle.
QR7E-0R51U1 Printing: January 2007 (09)
Nissan, the Nissan Brand Symbol, “SHIFT_” tagline, Z and Nissan model names are Nissan trademarks. ©2007 Nissan North America, Inc.
Sh ift_
sunroof controls (if so equipped)
The ignition switch must be in the ON position to operate the sunroof.
TILTING THE SUNROOF
 To tilt the sunroof up, first close the sunroof by pushing the switch toward UP/CLOSE 01. Release the switch, then push the UP/CLOSE switch again to tilt the sunroof up.
 To tilt the sunroof down, push the switch toward DOWN/OPEN 02.
SLIDING THE SUNROOF
 To fully open the sunroof, push the switch toward DOWN/OPEN. To open the sunroof part way, push the switch in any direction while the sunroof is sliding to stop it in the desired position.
 To fully close the sunroof, push the switch toward UP/CLOSE. To close the sunroof part way, push the switch in any direction while the sunroof is sliding to stop it in the desired position.
02
01
fuel-filler door
The fuel-filler door lock (if so equipped) is automatically engaged with the door lock system.
1. Unlock the fuel-filler door using one of the following
operations.
 Press the
lpd0151
button on the keyfob once to unlock
the driver’s door and the fuel-filler door.
 Unlock all doors with the key cylinder. (Turn twice.)
 Press
lpd0151
on the power door lock switch.
 NOTE: The fuel-filler door will remain locked if the driver’s door is manually
unlocked using the inside door lock handle lever.
2. Push the left side of the fuel-filler door to open.
3. To lock, close the fuel-filler door and lock all doors.