battery NISSAN TEANA 2003 Service Manual

INTELLIGENT KEY SYSTEM
BL-101
C
D
E
F
G
H
J
K
L
MA
B
BL

Check Key Switch (Intelligent Key Unit Input)BIS000XF
1. CHECK KEY SWITCH
With CONSULT-II
Display “KEY SW” on DATA MONITOR screen, and check if ON-
OFF display is linked to insertion of mechanical key in ignition knob.
OK or NG
OK >> Key switch is OK.
NG >> GO TO 2.
2. CHECK KEY SWITCH POWER SUPPLY CIRCUIT
1. Remove mechanical key from ignition knob.
2. Disconnect key switch connector.
3. Check voltage between key switch connector M20 terminal 3 (Y/B) and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace key switch power supply circuit.
3. CHECK KEY SWITCH OPERATION
Check continuity between key switch connector M20 terminal 3 and
8.
OK or NG
OK >> GO TO 4.
NG >> Replace key cylinder assembly (built-in key switch).KEY SW:
When key is inserted in ignition knob : ON
When key is removed in ignition knob : OFF
PIIB1359E
3 (Y/B) - Ground : Battery voltage
PIIB0938E
Connector Terminal Condition Continuity
M20 3 8Insert mechanical key
into ignition knob.Ye s
Remove mechanical key
from ignition knob.No
PIIB0942E

BL-102
INTELLIGENT KEY SYSTEM

4. CHECK KEY SWITCH CIRCUIT
1. Disconnect Intelligent Key unit connector.
2. Check continuity between Intelligent Key unit connector M31 terminal 7 (B/R) and key switch connector
M20 terminal 8 (B/R).
3. Check continuity between key switch connector M20 terminal 8
(B/R) and ground.
OK or NG
OK >> Check the condition of harness and connector.
NG >> Repair or replace harness between Intelligent Key unit
and key switch.
Check Key Switch (BCM Input)BIS000XG
1. CHECK KEY SWITCH POWER SUPPLY CIRCUIT
1. Turn ignition knob LOCK position.
2. Disconnect key switch connector.
3. Check voltage between key switch connector M20 terminal 3 (Y/
B) and ground.
OK or NG
OK >> GO TO 2.
NG >> Check harness between key switch and fuse.
2. CHECK KEY SWITCH
Check continuity between key switch as follows.
OK or NG
OK >> GO TO 3.
NG >> Replace key cylinder assembly (built-in key switch).7 (B/R) - 8 (B/R) : Continuity should exist.
8 (B/R) - Ground : Continuity should not exist.
PIIB0940E
3 (Y/B) – Ground : Battery voltage.
PIIB0941E
Connector Terminal Condition Continuity
M20 3 8Insert mechanical key
into ignition knob.Ye s
Remove mechanical key
from ignition knob.No
PIIB0942E

INTELLIGENT KEY SYSTEM
BL-103
C
D
E
F
G
H
J
K
L
MA
B
BL

3. CHECK KEY SWITCH SIGNAL CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between key switch connector M20 terminal 8
(B/R) and BCM connector M3 terminal 37 (B/R).
3. Check continuity between key switch connector M20 terminal 8
(B/R) and ground.
OK or NG
OK >> Key switch (BCM input) circuit is OK.
NG >> Repair or replace harness between key switch and BCM.
Check Ignition knob SwitchBIS000XH
1. CHECK IGNITION KNOB SWITCH
With CONSULT-II
Display “PUSH SW” on DATA MONITOR screen, and check if ON/
OFF display is linked to ignition knob operation.
Without CONSULT-II
1. Turn ignition knob LOCK position.
2. Disconnect Intelligent Key unit connector.
3. Check voltage between Intelligent Key unit connector M31 ter-
minal 27 (BR) and ground.
OK or NG
OK >> Ignition knob switch is OK.
NG >> GO TO 2.8 (B/R) – 37 (B/R) : Continuity should exist.
8 (B/R) – Ground : Continuity should not exist.
PIIB0943E
PUSH SW:
Press ignition knob. : ON
Return ignition knob (release hands
from ignition knob): OFF
PIIB1360E
Connec-
torTerminal (Wire color)
ConditionVoltage (V)
(Approx.)
(+) (–)
M31 27 (BR) GroundPress ignition knob Battery voltage
Return ignition knob
(Release hands from
ignition knob)0
PIIB1364E

BL-104
INTELLIGENT KEY SYSTEM

2. CHECK IGNITION KNOB SWITCH POWER SUPPLY CIRCUIT
1. Turn ignition knob LOCK position.
2. Disconnect ignition knob switch connector.
3. Check voltage between ignition knob switch connector M20 terminal 7 (Y/B) and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace key switch and ignition knob switch
power supply circuit.
3. CHECK IGNITION KNOB SWITCH OPERATION
Check continuity between ignition knob switch connector M20 terminal 7 and 2.
OK or NG
OK >> GO TO 4.
NG >> Replace key switch and ignition knob switch.
4. CHECK IGNITION KNOB SWITCH CIRCUIT
1. Disconnect Intelligent Key unit connector.
2. Check continuity between Intelligent Key unit connector M31 terminal 27 (BR) and ignition knob switch
connector M20 terminal 2 (BR).
3. Check continuity between ignition knob switch connector termi-
nal 2 (BR) and ground.
OK or NG
OK >> Check the condition of harness and connector.
NG >> Repair or replace harness between Intelligent Key unit
and key switch and ignition knob switch. 7 (Y/B) - Ground : Battery voltage
PIIB0944E
Connector Terminal Condition Continuity
M20 2 7Press ignition knob Yes
Return ignition knob
(Release hands from
ignition knob)No
PIIB0945E
27 (BR) - 2 (BR) : Continuity should exist.
2 (BR) - Ground : Continuity should not exist.
PIIB0946E

INTELLIGENT KEY SYSTEM
BL-105
C
D
E
F
G
H
J
K
L
MA
B
BL

Check Door SwitchBIS000XI
CHECK DOOR SWITCH (EXCEPT TRUNK ROOM LAMP SWITCH)
1. CHECK DOOR SWITCH INPUT SIGNAL
With CONSULT-II
Check door switches (“DOOR SW-DR”, “DOOR SW-AS”, “DOOR
SW-RL” and “DOOR SW-RR”) in “DATA MONITOR” mode with
CONSULT-II.
Without CONSULT-II
1. Turn ignition knob LOCK position.
2. Check voltage between BCM connector and ground.
OK or NG
OK >> Door switch circuit is OK.
NG >> GO TO 2.
Monitor item Condition
DOOR SW-DR
CLOSE → OPEN: OFF → ON DOOR SW-AS
DOOR SW-RL
DOOR SW-RR
Item ConnectorTerminals
(Wire color)Door
conditionVoltage (V)
(Approx.)
(+) (-)
Driver side
M562 (SB)
GroundCLOSE
↓
OPENBattery voltage
↓
0 Rear LH 63
(R/W)
Passenger side
M312 (R/L)
Rear RH13
(R/B)
PIIA6469E
PIIA7003E

INTELLIGENT KEY SYSTEM
BL-107
C
D
E
F
G
H
J
K
L
MA
B
BL

CHECK TRUNK ROOM LAMP SWITCH
1. CHECK TRUNK ROOM LAMP SWITCH INPUT SIGNAL
With CONSULT-II
Check (“TRUNK SW”) in “DATA MONITOR” mode with CONSULT-II.
Without CONSULT-II
1. Turn ignition knob LOCK position.
2. Check voltage between BCM connector and ground.
OK or NG
OK >> Trunk room lamp switch circuit is OK.
NG >> GO TO 2.
Monitor item Condition
TRUNK SWOPEN : ON
CLOSE : OFF
PIIB1362E
ConnectorTe r m i n a l
(Wire color)Back door condi-
tionVoltage (V)
(Approx.)
(+) (-)
M557
(V/W)GroundCLOSE
↓
OPENBattery voltage
↓
0
PIIB0947E

BL-108
INTELLIGENT KEY SYSTEM

2. CHECK TRUNK ROOM LAMP SWITCH CIRCUIT
1. Disconnect trunk room lamp switch connector.
2. Check voltage between trunk room lamp switch connector T7
terminal 3 (V/W) and ground. (Check harness for open.)
3. Disconnect BCM connector.
4. Check continuity between trunk room lamp switch connector T7
terminals 3 (V/W) and ground. (Check harness for short.)
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK TRUNK ROOM LAMP SWITCH
Check continuity between trunk room lamp switch terminal 1 and 3.
OK or NG
OK >> GO TO 4.
NG >> Replace trunk room lamp switch.3 (V/W) – Ground : Battery voltage
PIIB8794E
3 (V/W) – Ground : Continuity should not exist.
PIIB8795E
Terminal Back door condition Continuity
1 – 3Closed No
Open Yes
PIIB8796E

INTELLIGENT KEY SYSTEM
BL-111
C
D
E
F
G
H
J
K
L
MA
B
BL

5. CHECK DOOR REQUEST SWITCH CIRCUIT
1. Disconnect Intelligent Key unit connector.
2. Check continuity between Intelligent Key unit connector M31 terminals 5 (driver door), 25 (passenger
door), and 29 (trunk) and door request switch connector D25 (driver door), D43 (passenger door) terminal
3, T2 (trunk) terminal 2.
3. Check continuity between door request switch connector D25
(driver door), D43 (passenger door), T2 (trunk) terminals 3, 2
and ground.
OK or NG
OK >> Replace Intelligent Key unit.
NG >> Repair or replace harness between Intelligent Key unit and door request switch.
Check Intelligent Key Warning BuzzerBIS000XK
1. CHECK INTELLIGENT KEY WARNING BUZZER POWER SUPPLY CIRCUIT
1. Turn ignition knob LOCK position.
2. Disconnect Intelligent Key warning buzzer connector.
3. Check voltage between Intelligent Key warning buzzer connector D22 (driver side), B222 (trunk room) ter-
minal 1 (Y/R) and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace Intelligent Key warning buzzer power
supply circuit.
2. CHECK INTELLIGENT KEY WARNING BUZZER CIRCUIT
1. Disconnect Intelligent Key unit connector.
2. Check continuity between Intelligent Key unit connector M31 terminal 4, 23 and Intelligent Key warning
buzzer connector D22 (driver side), B222 (trunk room) terminal 2.
3. Check continuity between Intelligent Key warning buzzer con-
nector D22 (driver side), B222 (trunk room) terminal 2 and
ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness between Intelligent Key warning buzzer and Intelligent Key unit.Driver 5 (B/W) - 3 (B/W) : Continuity should exist.
Passenger 25 (P/L) - 3 (P/L) : Continuity should exist.
Trunk 29 (G/O) - 2 (G/O) : Continuity should exist.
2 (G/O) - Ground : Continuity should not exist.
3 (B/W, P/L) - Ground : Continuity should not exist.
PIIB0957E
1 (Y/R) - Ground : Battery voltage
PIIA6748E
Driver side:
4 (SB) - 2 (SB) : Continuity should exist.
Trunk room:
4 (SB) - 2 (LG/B) : Continuity should exist.
2 (SB) - Ground : Continuity should not exist.
PIIB8798E

BL-112
INTELLIGENT KEY SYSTEM

3. CHECK INTELLIGENT KEY WARNING BUZZER OPERATION
Connect battery power supply to Intelligent Key warning buzzer connector D22 (driver side), B222 (trunk
room) terminals 1 and 2, and check the operation.
OK or NG
OK >> Intelligent Key warning buzzer is OK.
NG >> Replace Intelligent Key warning buzzer
Check Outside Key AntennaBIS000XL
1. CHECK OUTSIDE KEY ANTENNA POWER SUPPLY-1
Push each door request switch, and use an oscilloscope to check voltage waveform of harness between Intel-
ligent Key unit connector M31 terminals 17 (rear bumper), 19 (driver door), and 37 (passenger door) and
ground.
OK or NG
OK >> Outside key antenna is OK.
NG >> GO TO 2.1 (BAT+) - 2 (BAT-) : the buzzer sounds
PIIA6750E
Push each door request switch.
Rear bumper:
17 (W/R) - Ground
Driver:
19 (P) - Ground
Passenger:
37 (GR) - Ground
MIIB0375E
SIIA1910J

INTELLIGENT KEY SYSTEM
BL-115
C
D
E
F
G
H
J
K
L
MA
B
BL

3. CHECK INSIDE KEY ANTENNA POWER SUPPLY-2
1. Replace inside key antenna.
2. Push ignition knob, and use an oscilloscope to check voltage
wave form between Intelligent key unit connector M31 terminals
13 (trunk room), 15 (center console), and 33 (instrument center
lower) and ground.
OK or NG
OK >> Inside key antenna is malfunctioning.
NG >> Replace Intelligent key unit.
Check Steering Lock UnitBIS000XN
1. CHECK STEERING LOCK UNIT POWER SUPPLY
1. Turn ignition knob to LOCK position.
2. Disconnect steering lock unit connector.
3. Check voltage between steering lock unit connector M21 terminal 1 (Y/B) and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace steering lock unit power supply circuit.
2. CHECK STEERING LOCK UNIT GROUND CIRCUIT
Check continuity between steering lock unit connector M21 terminal 4 (G/Y) and ground.
OK or NG
OK >> GO TO 3.
NG >> GO TO 4.
Push each door request switch.
Trunk room:
13 (V/W) - Ground
Center console:
15 (R/Y) - Ground
Instrument center lower:
33 (L/W) - Ground
PIIB8801E
SIIA1910J
1 (Y/B) - Ground : Battery voltage
PIIA6797E
4 (G/Y) - Ground : Continuity should exist.
PIIA6798E