Reverse NISSAN TEANA 2003 Service Manual

CVT-178
SHIFT CONTROL SYSTEM

8. Remove control device assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.

The knurled surface of rib should be upward when installing the
control cable to the control device assembly. And insert the con-
trol cable securely.

After installation is completed, adjust and check CVT position.
Refer to CVT-178, "
Adjustment of CVT Position" and CVT-179,
"Checking of CVT Position" .
Adjustment of CVT PositionBCS001MN
1. Place selector lever in “P” position.
2. Loosen control cable nut and place manual lever in “P” position.
CAUTION:
Turn wheels more than 1/4 rotations and apply the park
lock.
3. Hold the control cable at the end. Push and pull it twice or three
times, and then push it with a load of 9.8N (approximately 1 kg,
2.2 lb). Temporarily tighten the lock nut with the control cable
loose.
4. Connect control cable on manual lever.
CAUTION:
No application of a force to the manual lever.
5. Tighten control cable nut.
CAUTION:
Fix the manual lever when tightening.
SCIA5964E
SCIA5990E
: 12.7 N·m (1.3 kg-m, 9 ft-lb)
SCIA2001E

CVT-186
AIR BREATHER HOSE

AIR BREATHER HOSEPFP:31098
Removal and InstallationBCS001MV
COMPONENTS
REMOVAL
Refer to the figure for air breather hose removal procedure.
INSTALLATION
Note the following, and install in the reverse order of removal.

Install air breather hose (1) to air breather tube (2) so that the
paint mark (A) faces leftward. Also make sure air breather hose
end laps with air breather tube 17 mm (0.67 in) or more.

When installing air breather hose (1) to air duct assembly, make
sure to fully insert the hose with clip (2).
1. Air duct assembly 2. Transmission assembly 3. Air breather tube
4. Air breather hose
SCIA7895E
SCIA7896E
SCIA7897E

CVT-192
CVT FLUID COOLER SYSTEM

INSTALLATION
Note the following, and install in the reverse order of removal.

After completing installation, check for engine coolant leakage, engine coolant level, and the positions of
CVT. Refer to CO-34, "
Inspection" and CVT-179, "Checking of CVT Position" .
CAUTION:

Install hose clamp with tabs aligned with markings of CVT fluid cooler valve assembly and each
hose.

Do not reuse CVT fluid cooler inlet tube assembly and CVT fluid cooler outlet tube assembly.

Apply LLC around O-ring when installing CVT fluid cooler inlet tube and CVT fluid cooler outlet
tube assembly to CVT fluid cooler valve assembly.
COMPONENT INSPECTION
1. Make sure that CVT fluid cooler valve is fully opened at room
temperature.
2. Put CVT fluid cooler valve into a water-filled container, and then
heat it up to 82°C (180°F) or more for 10 minutes or more.
3. Make sure that CVT fluid cooler valve is fully closed.Standard
Dimension A from CVT fluid cooler valve port end
to tip of valve shaft
(At room temperature):
Approx 72.0 mm (2.835 in) or more
SCIA7399E
SCIA2710E
Standard
Dimension A from CVT fluid cooler valve port end
to tip of valve shaft
[When heating to 82°C (180°F) or more for 10 min-
utes or more]:
Approx 66.5 mm (2.618 in) or less
SCIA7399E

CVT-196
TRANSAXLE ASSEMBLY

INSPECTION
Installation and Inspection of Torque Converter

After inserting a torque converter to a transaxle, be sure to
check distance “A” to ensure it is within the reference value limit.
INSTALLATION
Note the following, and install in the reverse order of removal.

Set and screw in the drive plate location guide onto the stud
bolts for the torque converter locate.

Rotate the torque converter for the locate to go down.

Rotate the drive plate for the hole of the drive plate locate to go
down.Distance “A”: 14.0 mm (0.55 in) or more
SCIA6858E
SCIA1871E
SCIA6881E
SCIA1872E

CVT-198
SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
General SpecificationsBCS001N1
*1: Refer to MA-14, "Fluids and Lubricants" .
Vehicle Speed at Which Gear Shifting OccursBCS001N2
Numerical value data are reference values.
CAUTION:
Lock-up clutch is engaged when vehicle speed is approximately 18 km/h (11 MPH) to 90 km/h (56 MPH).
Stall SpeedBCS001N3
Line PressureBCS001N4
*1 : Reference values
Solenoid ValvesBCS001N5
Applied modelVQ35DE engine
2WD
CVT modelRE0F09A
CVT assembly Model code number 1XD14
Transmission gear ratioD range Variable
Reverse 1.766
Final drive 5.173
Recommended fluid NISSAN CVT Fluid NS-2*1
Fluid capacity 10.2 liter (9 Imp qt)
CAUTION:

Use only Genuine NISSAN CVT Fluid NS-2. Do not mix with other fluid.

Using CVT fluid other than Genuine NISSAN CVT Fluid NS-2 will deteriorate in driveability and CVT durability, and may
damage the CVT, which is not covered by the warranty.
Engine type Throttle position Shift patternEngine speed (rpm)
At 40 km/h (25 MPH) At 60 km/h (37 MPH)
VQ35DE8/8 “D” position 3,100 - 4,200 4,200 - 5,300
2/8 “D” position 1,200 - 2,000 1,300 - 2,100
Stall speed 2,700 - 3,250 rpm
Engine Engine speedLine pressure kPa (bar, kg/cm2 , psi)
“R”, “D” positions
VQ35DEAt idle speed 750 (7.50, 7.65, 108.8)
At stall speed
5,700 (57.00, 58.14, 826.5)*
1
Name Resistance (Approx.) Terminal
Pressure control solenoid valve B (Secondary
pressure solenoid valve)
3 - 9 Ω3
Pressure control solenoid valve A (Line pressure
solenoid valve)2
Torque converter clutch solenoid valve12
Lock-up select solenoid valve 6 - 19 Ω13

COMBINATION METERS
DI-25
C
D
E
F
G
H
I
J
L
MA
B
DI

Removal and Installation of Combination MeterBKS001SI
REMOVAL
1. Remove cluster lid A. Refer to IP-11, "Removal and Installation" .
2. Remove screws (3) and remove combination meter.
INSTALLATION
Installation is the reverse order of removal.
Disassembly and Assembly of Combination MeterBKS001SJ
SKIB0867E
SKIB0868E
1. Unified meter control unit assembly 2. Upper housing 3. Front cover
4. Odo/trip meter 5. Screw
SKIA6276J

DI-26
COMBINATION METERS

DISASSEMBLY
1. Disengage the tabs (8) to separate front cover.
2. Disconnect odo/trip meter connector.
3. Disengage the tabs (8) to separate upper housing.
4. Remove screws (1) and remove odo/trip meter.
ASSEMBLY
Assembly is the reverse order of disassembly.
SKIB0868E
SKIA7244E

DI-34
UNIFIED METER AND A/C AMP

8. CHECK VOLTAGE SIGNAL OF UNIFIED METER AND A/C AMP.
1. Turn ignition switch OFF and connect unified meter and A/C amp. connector.
2. Turn ignition switch ON.
3. Check voltage signal between combination meter harness con-
nector M70 terminal 19 and ground.
OK or NG
OK >> Replace combination meter.
NG >> Replace unified meter and A/C amp. Refer to DI-34, "
Removal and Installation of Unified Meter
and A/C Amp." .
DTC [B2205] Vehicle Speed CircuitBKS002B3
1. CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
Perform the ABS actuator and electric unit (control unit) self-diagnosis. Refer to BRC-57, "
CONSULT-II Func-
tions" (with VDC system) or BRC-17, "CONSULT-II Functions (ABS)" (without VDC system).
Self
-diagnostic results content
No malfunction detected>>Replace unified meter and A/C amp.
Malfunction detected>>Check applicable parts, and repair or replace corresponding parts.
Removal and Installation of Unified Meter and A/C Amp.BKS001SP
REMOVAL
1. Remove the audio unit. Refer to AV- 1 5 , "Removal and Installa-
tion of Audio Unit" (with integrated display system) or AV- 3 4 ,
"Removal and Installation of Audio Unit" (with integrated color
display system).
2. Remove screws (5) and remove bracket.
3. Remove screw and remove the unified meter and A/C amp.
(Auto amp.)
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Unified meter and A/C amp. screws (2) are different from other securing screws. Never confuse them
when installing.19 – Ground:
SKIA8732E
SKIA3362E
SKIA8643E

EC-30
[QR]
POSITIVE CRANKCASE VENTILATION

POSITIVE CRANKCASE VENTILATIONPFP:11810
DescriptionBBS005BM
SYSTEM DESCRIPTION
This system returns blow-by gas to the intake manifold.
The positive crankcase ventilation (PCV) valve is provided to conduct crankcase blow-by gas to the intake
manifold. During partial throttle operation of the engine, the intake manifold sucks the blow-by gas through the
PCV valve. Normally, the capacity of the valve is sufficient to handle any blow-by and a small amount of venti-
lating air. The ventilating air is then drawn from the air inlet tubes into the crankcase. In this process the air
passes through the hose connecting air inlet tubes to rocker cover. Under full-throttle condition, the manifold
vacuum is insufficient to draw the blow-by flow through the valve. The flow goes through the hose connection
in the reverse direction.
On vehicles with an excessively high blow-by, the valve does not
meet the requirement. This is because some of the flow will go
through the hose connection to the air inlet tubes under all condi-
tions.
Component InspectionBBS005BN
PCV (POSITIVE CRANKCASE VENTILATION) VALVE
With engine running at idle, remove PCV valve from rocker cover. A
properly working valve makes a hissing noise as air passes through
it. A strong vacuum should be felt immediately when a finger is
placed over valve inlet.
PBIB0492E
PBIB1588E
PBIB1589E

EC-370
[VQ]
POSITIVE CRANKCASE VENTILATION

POSITIVE CRANKCASE VENTILATIONPFP:11810
DescriptionBBS004XT
SYSTEM DESCRIPTION
This system returns blow-by gas to the intake manifold.
The positive crankcase ventilation (PCV) valve is provided to conduct crankcase blow-by gas to the intake
manifold. During partial throttle operation of the engine, the intake manifold sucks the blow-by gas through the
PCV valve. Normally, the capacity of the valve is sufficient to handle any blow-by and a small amount of venti-
lating air. The ventilating air is then drawn from the air inlet tubes into the crankcase. In this process the air
passes through the hose connecting air inlet tubes to rocker cover. Under full-throttle condition, the manifold
vacuum is insufficient to draw the blow-by flow through the valve. The flow goes through the hose connection
in the reverse direction.
On vehicles with an excessively high blow-by, the valve does not
meet the requirement. This is because some of the flow will go
through the hose connection to the air inlet tubes under all condi-
tions.
Component InspectionBBS004XU
PCV (POSITIVE CRANKCASE VENTILATION) VALVE
With engine running at idle, remove PCV valve from rocker cover. A
properly working valve makes a hissing noise as air passes through
it. A strong vacuum should be felt immediately when a finger is
placed over valve inlet.
SEC921C
PBIB1588E
PBIB1589E