Reverse NISSAN TEANA 2003 Service Manual

INTEGRATED COLOR DISPLAY SYSTEM
AV-113
C
D
E
F
G
H
I
J
L
MA
B
AV

Removal and Installation of Rear View CameraBKS0028I
REMOVAL
1. Remove trunk lid finisher (upper). Refer to EI-33, "TRUNK LID FINISHER" .
2. Disconnect connector and remove connector clip.
3. While pressing the rear view camera to left side, pull right side
pawl of it and remove.
INSTALLATION
Installation is the reverse order of removal.
Adjust the vehicle width and distance guiding line referring to AV- 9 5 , "
Vehicle Width and Distance Guiding Line
Correction" if there is a difference after installing rear view camera.
Removal and Installation of Rear View Camera Control UnitBKS0028J
REMOVAL
1. Remove trunk wheelhouse finisher (Left side). Refer to EI-58, "TRUNK ROOM TRIM & TRUNK LID FIN-
ISHER" .
2. Remove screw and remove rear view camera control unit.
3. Disconnect connector.
INSTALLATION
Installation is the reverse order of removal.
SKIA6281E
SKIA6282E

BCS-16
BCM (BODY CONTROL MODULE)

Removal and Installation of BCMBKS001UN
REMOVAL
1. Remove the Instrument driver lower panel. Refer to IP-11,
"Removal and Installation" .
2. Remove screws.
3. Disconnect BCM connector.
INSTALLATION
Installation is the reverse order of removal.
NOTE:
When replacing BCM, perform initialization of NATS system and registration of all NATS ignition key IDs. Refer
to BL-139, "
NATS(Nissan Anti-Theft System)" .
PKIB0266E

HOOD
BL-15
C
D
E
F
G
H
J
K
L
MA
B
BL

REMOVAL
Hood Assembly
1. Support the hood striker with a proper material to prevent it from
falling.
WARNING:
Body injury may occur if no supporting rod is holding the
hood open when removing the hood stay.
2. Disconnect washer hose at the connecting point.
3. Remove the hood stays from the stud balls on the body side.
4. Remove hinge nuts on hood and remove hood assembly.
CAUTION:
Operate with two workers, because of its heavy weight.
INSTALLATION

Install in the reverse order of removal.

Apply Anti-Corrosion or equivalent to the attaching portion of hood hinge, hood ledge, and hood assembly.

After installing, perform hood fitting adjustment. Refer to BL-13, "Fitting Adjustment" .
PIIB0261E
: 12.7 N·m (1.3 kg-m, 9 ft-lb)
PIIB0262E

BL-16
HOOD

Removal and Installation of Hood Lock ControlBIS000VR
REMOVAL
Hood Lock and Hood Lock Cable
1. Remove hood lock bolts.
2. Disconnect hood lock cable from hood lock.
3. Remove fender protector (LH). Refer to EI-23, "
FENDER PRO-
TECTOR" .
4. Remove hood lock cable clips, from radiator core upper support
and hood ledge.
5. Remove hood opener and grommet on lower dashboard.
6. Pull out hood lock cable toward passenger room.
CAUTION:
While pulling the cable, be careful not to damage (peel) outer surface of the cable on edges of
body through hole.
INSTALLATION
Install in the reverse order of removal.
1. Pull the hood lock cable through the panel hole to the engine
compartment.
CAUTION:
Be careful not to bend the cable too much, keeping the
radius 100 mm (3.94 in) or more.
2. Make sure that the cable is not offset from the positioning grommet, and push the grommet into the panel
hole securely.
3. Apply sealant (POS seal) to area on the grommet indicated with the * mark.
1. Hood lock cable 2. Hood lock
PIIB1753E
: 23.6N·m (2.4 kg-m, 18 ft-lb)
PIIB1754E
PIIA0173E

RADIATOR CORE SUPPORT
BL-19
C
D
E
F
G
H
J
K
L
MA
B
BL

12. Remove radiator core support upper, side, and center as a single piece. Remove mounting bolts and nuts
with power tool.
13. After removing radiator core support upper, side, and center as a single piece, separate the following
parts.

Horns (High/Low)

Air guides (LH/RH)

Radiator core support side (LH/RH)

Radiator core upper support

Radiator core support center
INSTALLATION
Install in the reverse order of removal.
CAUTION:
After installing, check the hood adjustment and hood opener operation. Refer to BL-17, "
Hood Lock
Control Inspection" .

BL-20
FRONT FENDER

FRONT FENDERPFP:63100
Removal and InstallationBIS000VU
REMOVAL
1. Remove the front bumper. Refer to EI-14, "FRONT BUMPER" .
2. Remove fender protector mounting clips and screws from out side. Refer to EI-23, "
FENDER PROTEC-
TOR" .
3. Remove center mud guard. Refer to EI-24, "
CENTER MUD GUARD" .
4. Remove bolts securing radiator core support side.
5. Remove hood hinge cover (rubber). Refer to EI-21, "
COWL TOP" .
6. Remove side turn signal lamp.
7. Remove bolts, and then remove front fender.
CAUTION:
While removing use a shop cloth to protect body from damaging.
INSTALLATION
Install in the reverse order of removal.
CAUTION:

After installing, apply touch-up paint (the body color) onto the head of the front fender mounting
bolts.

After installing, check front fender adjustment. Refer to BL-13, "Fitting Adjustment" and BL-119,
"Fitting Adjustment" .
1. Bolt 2. Front fender
PIIB0267E

INTELLIGENT KEY SYSTEM
BL-117
C
D
E
F
G
H
J
K
L
MA
B
BL

Check Headlamp FunctionBIS000XO
First perform the “SELF-DIAG RESULTS” in “BCM” with CONSULT-II, then perform the trouble diagnosis of
malfunction system indicated “SELF-DIAG RESULTS” of “BCM”. Refer to BCS-14, "
CAN Communication
Inspection Using CONSULT-II (Self-Diagnosis)" .
1. CHECK HEADLAMP OPERATION
Does headlamp come on when turning lighting switch “ON”?
YES or NO
YES >> Headlamp operation circuit is OK.
NO >> Check headlamp system. Refer to LT- 6 , "
HEADLAMP - XENON TYPE -" .
Removal and Installation of Intelligent Key UnitBIS001TH
REMOVAL
1. Remove the instrument driver lower panel. Refer to IP-10, "Component Parts Location" .
2. Disconnect Intelligent Key unit connector, remove screw and
Intelligent Key unit.
INSTALLATION
Install in the reverse order of removal.
Intelligent Key Battery ReplacementBIS001TI
DISASSEMBLY AND ASSEMBLY OF INTELLIGENT KEY
1. Release the lock knob at the back of the Intelligent Key and remove the mechanical key.
2. Insert a flat-blade screwdriver (A) wrapped with a close into the
slit of the corner and twist it to separate the upper part from the
lower part.
CAUTION:

Be careful not to touch the circuit board or battery termi-
nal.

The key fob is water-resistant. However, if it does get wet,
immediately wipe it dry.
3. Replace the battery with new one.
4. Align the tips of the upper and lower parts, and then push them
together until it is securely closed.
CAUTION:

When replacing battery, be sure to keep dirt, grease, and
other foreign materials off the electrode contact area.

After replacing the battery, check to make sure all Intelli-
gent Key functions work normally.
PIIB0276E
PIIB6221E
PIIB6222E

BL-120
DOOR

STRIKER ADJUSTMENT
Adjust the striker so that it becomes parallel with the lock insertion
direction.
Removal and Installation of Front DoorBIS000XS
CAUTION:

When removing and installing the front door assembly, support the door with a jack and cloth to
protect the door and body.

When removing and installing front door assembly, be sure to perform the fitting adjustment Refer
to BL-119, "
Fitting Adjustment" .

Operate with two workers, because of its heavy weight.

Check the hinge rotating part for poor lubrication. If necessary, apply “body grease”.

After installing, check operation.
REMOVAL
1. Disconnect the front door harness connector.
2. Remove the mounting bolts of the check link on the vehicle.
3. Remove the door-side hinge mounting nuts, and remove the
door assembly.
INSTALLATION
Install in the reverse order of removal.
Removal and Installation of Rear DoorBIS000XT
CAUTION:

When removing and installing the rear door assembly, support the door with a jack and cloth to
protect the door and body.

When removing and installing rear door assembly, be sure to perform the fitting adjustment Refer
to BL-119, "
Fitting Adjustment" . : 16.7 N·m (1.7 kg-m, 12 ft-lb)
PIIB1226E
: 14.7 N·m (1.5 kg-m, 11 ft-lb)
PIIB1227E
: 24.5 N·m (2.5 kg-m, 18 ft-lb)
PIIB0279E

DOOR
BL-121
C
D
E
F
G
H
J
K
L
MA
B
BL


Operate with two workers, because of its heavy weight.

Check the hinge rotating part for poor lubrication. If necessary, apply “body grease”.

After installing, check operation.
REMOVAL
1. Grommet is pulled out, and the Rear door harness connector is detached.
2. Remove the mounting bolts of the check link on the vehicle.
3. Remove the door-side hinge mounting nuts, and remove the
door assembly.
INSTALLATION
Install in the reverse order of removal.
Removal and Installation of Door WeatherstripBIS000XU
REMOVAL
1. Remove the mounting bolts of the check link on the vehicle. Refer to BL-120, "Removal and Installation of
Front Door" or BL-120, "Removal and Installation of Rear Door" .
2. Remove the weatherstrip clips and remove weatherstrip.: 14.7 N·m (1.5 kg-m, 11 ft-lb)
PIIB1227E
: 24.5 N·m (2.5 kg-m, 18 ft-lb)
PIIB0280E
1. Weatherstrip 2. Clip
PIIB0281E

BL-122
DOOR

INSTALLATION
Install in the reverse order of removal.