relay NISSAN TEANA 2003 User Guide

BRC-56
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS

Note 1: Confirm tire pressure is the standard value.
Note 2: Warning lamp can be used as both EBD warning lamp and brake warning.N POSI SIGShift position determined by the A/T
switch signalWhen in N position ON
Other than N position OFF
P POSI SIGShift position determined by the A/T
switch signalWhen in P position ON
Other than P position OFF
FR LH IN SOL
FR LH OUT SOL
FR RH IN SOL
FR RH OUT SOL
RR LH IN SOL
RR LH OUT SOL
RR RH IN SOL
RR RH OUT SOLOperation condition of all solenoid
valvesActuator (solenoid) is active (“ACTIVE
TEST” with CONSULT-II) and actuator
relay is active (ignition switch ON)ON
When actuator (solenoid) is not active
or actuator relay is not active (in fail-
safe mode)OFF
STOP LAMP SW2 Brake pedal operation conditionBrake pedal depressed ON
Brake pedal not depressed OFF
ACCEL POS SIGAccelerator open/close condition
(linked to the accelerator pedal)Do not step on the accelerator pedal
(When ignition switch is on)0 %
Step on the accelerator pedal
(When ignition switch is on)0 - 100 %
SIDE G SENSOR Side G detected by side G sensorWhen stopped
−1.1 to +1.1 m/s
2
Right turn Negative value
Left turn Positive value
STR ANGLE SIGSteering angle detected by steering
angle sensorStraight-ahead position -3.5° to 3.5°
Steering wheel turned right 0° to 756°
Steering wheel turned left 0° to -756°
EBD SIGNAL EBD operation conditionEBD activated ON
EBD not activated OFF
ABS SIGNAL ABS operation conditionABS activated ON
ABS not activated OFF
TCS SIGNAL TCS operation conditionTCS activated ON
TCS not activated OFF
VDC SIGNAL VDC operation conditionVDC activated ON
VDC not activated OFF
EBD FAIL SIG EBD fail-safe signal conditionIn EBD fail-safe ON
EBD is normal OFF
ABS FAIL SIG ABS fail-safe signal conditionIn ABS fail-safe ON
ABS is normal OFF
TCS FAIL SIG TCS fail-safe signal conditionIn TCS fail-safe ON
TCS is normal OFF
VDC FAIL SIG VDC fail-safe signal conditionIn VDC fail-safe ON
VDC is normal OFF
CRANKING SIG Cranking conditionAt cranking ON
Other than at cranking OFF
FLUID LEV SWBrake fluid level switch ON/OFF con-
ditionWhen brake fluid level switch is ON ON
When brake fluid level switch is OFF OFF Monitor item Display itemDATA MONITOR
ConditionReference values for
normal operation

TROUBLE DIAGNOSIS
BRC-59
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

DISPLAY ITEM LIST
Diagnostic item Diagnostic item is detected when... Reference
RR RH SENSOR−1
[C1101]When the circuit in the rear right wheel sensor is open.
BRC-68, "
Wheel Sensor
System"
(Note 1) RR LH SENSOR−1
[C1102]When the circuit in the rear left wheel sensor is open.
FR RH SENSOR−1
[C1103]When the circuit in the front right wheel sensor is open.
FR LH SENSOR−1
[C1104]When the circuit in the front left wheel sensor is open.
RR RH SENSOR−2
[C1105]When the circuit in the rear right wheel sensor is shorted. Or when
the sensor power voltage is outside the standard. When the dis-
tance between the wheel sensor and sensor rotor is too large and
the sensor pulse cannot be recognized by the control unit.
RR LH SENSOR−2
[C1106]When the circuit in the rear left wheel sensor is shorted. Or when
the sensor power voltage is outside the standard. When the dis-
tance between the wheel sensor and sensor rotor is too large and
the sensor pulse cannot be recognized by the control unit.
FR RH SENSOR−2
[C1107]When the circuit in the front right wheel sensor is shorted. Or when
the sensor power voltage is outside the standard. When the dis-
tance between the wheel sensor and sensor rotor is too large and
the sensor pulse cannot be recognized by the control unit.
FR LH SENSOR−2
[C1108]When the circuit in the front left wheel sensor is shorted. Or when
the sensor power voltage is outside the standard. When the dis-
tance between the wheel sensor and sensor rotor is too large and
the sensor pulse cannot be recognized by the control unit.
BATTERY VOLTAGE
[ABNORMAL]
[C1109]Battery voltage of control unit is too low.BRC-78, "
ABS Actuator
and Electric Unit (Control
Unit) Power Supply and
Ground System"
CONTROLLER FAILURE
[C1110]When there is an internal malfunction in the control unit.BRC-70, "ABS Actuator
and Electric Unit (Control
Unit) 1"
PUMP MOTOR
[ C 1111 ]This is displayed when the control unit detects a malfunction in the
motor or motor relay.BRC-74, "Pump Motor,
Motor Relay System"
G-SENSOR
[C1113]Longitudinal G-sensor is malfunctioning, or signal line of longitudi-
nal G-sensor is open or shorted.BRC-72, "Yaw Rate/Side/
Decel G Sensor System"
STOP LAMP SW
[C1116]Stop lamp switch circuit is open.BRC-77, "Stop Lamp
Switch System"

BRC-60
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS

Note 1: After completing repairs of the shorted sensor circuit, when ignition switch is turned ON, ABS warning lamp turns on. Make sure
that ABS warning lamp turns off while driving the vehicle at 30 km/h (19 MPH) or more for approximately 1 minute according to self-diag- FR LH IN ABS SOL
[C1120]This is displayed when the control unit detects a malfunction in the
front left wheel inlet solenoid circuit.
BRC-76, "
Solenoid and
VDC Change-Over Valve,
Actuator Relay System"
FR LH OUT ABS SOL
[C1121]This is displayed when the control unit detects a malfunction in the
front left wheel outlet solenoid circuit.
FR RH IN ABS SOL
[C1122]This is displayed when the control unit detects a malfunction in the
front right wheel inlet solenoid circuit.
FR RH OUT ABS SOL
[C1123]This is displayed when the control unit detects a malfunction in the
front right wheel outlet solenoid circuit.
RR LH IN ABS SOL
[C1124]This is displayed when the control unit detects a malfunction in the
rear left wheel inlet solenoid circuit.
RR LH OUT ABS SOL
[C1125]This is displayed when the control unit detects a malfunction in the
rear left wheel outlet solenoid circuit.
RR RH IN ABS SOL
[C1126]This is displayed when the control unit detects a malfunction in the
rear right wheel inlet solenoid circuit.
RR RH OUT ABS SOL
[C1127]This is displayed when the control unit detects a malfunction in the
rear right wheel outlet solenoid circuit.
CV 1
[C1164]When cut valve 1 circuit is open or shorted.
CV 2
[C1165]When cut valve 2 circuit is open or shorted.
SV 1
[C1166]When suction valve 1 circuit is open or shorted.
SV 2
[C1167]When suction valve 2 circuit is open or shorted.
ACTUATOR RLY
[C1140]This is displayed when the control unit detects a malfunction in
actuator relay circuit.
ENGINE SIGNAL 1- 6
[C1130, C1131, C1132, C1133,
C1134, C1136]When there is a malfunction in an engine system main
component.BRC-70, "
Engine Sys-
tem"
ST ANGLE SIG CIRCUIT
[C1143]When the steering angle sensor neutral position has deviated. Or
when a steering angle sensor malfunction is detected.BRC-71, "Steering Angle
Sensor System"
ST ANG SEN SIGNAL
[C1144]Neutral position correction of steering angle sensor is not finished.BRC-40, "Adjustment of
Steering Angle Sensor
Neutral Position"
YAW RATE SENSOR
[C1145]When yaw rate sensor malfunction is detected. Or when a yaw rate
sensor circuit open or short circuit is detected.
BRC-72, "
Yaw Rate/Side/
Decel G Sensor System"SIDE G-SEN CIRCUIT
[C1146]When a side G sensor malfunction is detected. Or the circuit of side
G sensor is open or shorted.
PNP POSI SIG
[C1154]TCS or ABS actuator and electric unit (control unit) internal mal-
function.BRC-75, "
Park/Neutral
Position (PNP) Switch
Circuit"
BR FLUID LEVEL LOW
[C1155]Brake fluid level drops. Or, when there is a short to ground in the
circuit between the ABS actuator and electric unit (control unit) and
the brake fluid level switch.BRC-80, "Brake Fluid
Level Switch System"
ST ANG SEN COM CIR
[C1156]CAN communication system or steering angle sensor has gener-
ated a malfunction.BRC-81, "CAN Communi-
cation System"
STOP LAMP SW2
[C1176]ASCD brake switch or circuit malfunction.EC-602, "DTC P1572
ASCD BRAKE SWITCH"
CAN COMM CIRCUIT
[U1000]When there is a malfunction in the CAN communication system.BRC-81, "CAN Communi-
cation System"
(Note 2) Diagnostic item Diagnostic item is detected when... Reference

TROUBLE DIAGNOSIS
BRC-61
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

nosis procedure. In addition, if wheel sensor 2 is displayed for the wheels, check the wheel sensor circuit and also check the control unit
power voltage.
Note 2: When malfunctions are detected in several systems, including the CAN communication system [U1000], perform trouble diagno-
sis on the CAN communication system.
Data MonitorBFS000E4
OPERATION PROCEDURE
1. Turn ignition switch OFF.
2. Perform “CONSULT-II Starting Procedure”. Refer to GI-34, "
CONSULT-II Start Procedure" .
3. Turn ignition switch ON.
4. At the monitor item selection screen, touch one of the items “ECU INPUT SIGNALS”, “MAIN SIGNALS” or
“SELECTION FROM MENU”.
5. Touch “START” to proceed to the data monitor screen.
DISPLAY ITEM LIST
Item (Unit)Monitor item selection
Remarks
ECU INPUT
SIGNALSMAIN SIGNALSSELECTION
FROM MENU
FR LH SENSOR
[km/h (MPH)]×××Condition of wheel speed calculated by front left
wheel sensor signal is displayed.
FR RH SENSOR
[km/h (MPH)]×××Condition of wheel speed calculated by front right
wheel sensor signal is displayed.
RR LH SENSOR
[km/h (MPH)]×××Condition of wheel speed calculated by rear left wheel
sensor signal is displayed.
RR RH SENSOR
[km/h (MPH)]×××Condition of wheel sensor calculated by rear right
wheel sensor signal is displayed.
DECEL G SEN
(G)×××Condition of decel G detected by the decel G sensor
is displayed.
FR LH IN SOL
(ON/OFF)—××Condition of front left wheel ABS inlet solenoid valve
(ON/OFF) is displayed.
FR LH OUT SOL
(ON/OFF)—××Condition of front left wheel ABS outlet solenoid valve
(ON/OFF) is displayed.
RR RH IN SOL
(ON/OFF)—××Condition of rear right wheel ABS inlet solenoid valve
(ON/OFF) is displayed.
RR RH OUT SOL
(ON/OFF)—××Condition of rear right wheel ABS outlet solenoid
valve (ON/OFF) is displayed.
FR RH IN SOL
(ON/OFF)—××Condition of front right wheel ABS inlet solenoid valve
(ON/OFF) is displayed.
FR RH OUT SOL
(ON/OFF)—××Condition of front right wheel ABS outlet solenoid
valve (ON/OFF) is displayed.
RR LH IN SOL
(ON/OFF)—××Condition of rear left wheel ABS inlet solenoid valve
(ON/OFF) is displayed.
RR LH OUT SOL
(ON/OFF)—××Condition of rear left wheel ABS outlet solenoid valve
(ON/OFF) is displayed.
EBD WARN LAMP
(ON/OFF) (Note)——×Condition of brake warning lamp (ON/OFF) is dis-
played.
STOP LAMP SW
(ON/OFF)×××Condition of stop lamp switch (ON/OFF) is displayed.
MOTOR RELAY
(ON/OFF)—××Condition of ABS motor relay (ON/OFF) is displayed.
ACTUATOR RLY
(ON/OFF)—××Condition of ABS actuator relay (ON/OFF) is dis-
played.
ABS WARN LAMP
(ON/OFF)—××Condition of ABS warning lamp (ON/OFF) is dis-
played.

BRC-64
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS

TEST ITEM
Solenoid Valve
NOTE:
The example shown is for the front right wheel. The procedure for the other wheels is the same as given
below.

When performing an active test of the ABS function, select the main item for each test item. In addition,
when performing an active test of the VDC/TCS function, select the item menu for each test item.

For the ABS solenoid valve, touch “UP” “KEEP” “DOWN”, and
for the ABS solenoid valve (ACT), touch “UP” “ACTUATOR UP”
“ACTUATOR KEEP”, and make sure that all solenoid valves (in,
out) are operating as given in the chart.
CAUTION:
Operate rear wheel valve when selecting front wheel and
operate front wheel valve when selecting rear wheel for
ABS solenoid valve (ACT).
Solenoid Valve Operation Chart
*: ON for 1 to 2 seconds after the touch, and then OFF
ABS Motor
Touch “ON ” and “OFF” on the screen, and check if ABS motor relay
and ABS actuator relay are operating as given in the following table.
SFIA2097E
OperationABS solenoid valve ABS solenoid valve (ACT)
UP KEEP DOWN UPACTUATOR
UPACTUATOR
KEEP
FR RH IN SOL OFF ON ON OFF OFF OFF
FR RH OUT SOL OFF OFF ON* OFF OFF OFF
SV 1 OFF OFF OFF OFF OFF* OFF
CV 1 OFF OFF OFF OFF OFF ON
Operation ON OFF
MOTOR RELAY ON OFF
ACTUATOR RLY ON ON
SFIA0593E

BRC-74
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS FOR SYSTEM

Pump Motor, Motor Relay SystemBFS000ED
INSPECTION PROCEDURE
1. CHECK SELF-DIAGNOSTIC RESULTS
Check the self-diagnostic results.
Is above displayed on self-diagnosis display?
YES >> GO TO 2.
NO >> INSPECTION END
2. CHECK CONNECTOR
1. Turn ignition switch OFF, disconnect the ABS actuator and electric unit (control unit) connector, and check
terminal for deformation, disconnection, looseness, and so on. If there is a malfunction, repair or replace
the terminal.
2. Securely reconnect connectors and perform self-diagnosis again.
OK or NG
OK >> Connector terminal contact was loose, damaged, open or shorted.
NG >> GO TO 3.
3. CHECK ABS MOTOR AND MOTOR RELAY POWER SYSTEM
1. Turn ignition switch OFF and disconnect ABS actuator and elec-
tric unit (control unit) connector.
2. Check voltage between the ABS actuator and electric unit (con-
trol unit) harness connector E241 terminal 1 and ground.
OK or NG
OK >> GO TO 4.
NG >> Circuit malfunction between battery and ABS actuator
and electric unit (control unit). Repair circuit.
4. CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) GROUND CIRCUIT

ABS actuator and electric unit (control unit) harness connector
E241 terminals 31, 46 and ground.
OK or NG
OK >> Replace ABS actuator and electric unit (control unit).
NG >> Harness or connector is open or shorted. Repair or
replace malfunctioning components.
Self-diagnostic results
PUMP MOTOR
ABS actuator and electric unit (contorl unit) Ground Voltage
1—Battery voltage
(Approx. 12 V)
SFIA2100E
ABS actuator and electric unit (contorl unit) Ground Continuity
31, 46 — Yes
SFIA2114E

BRC-76
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS FOR SYSTEM

Solenoid and VDC Change-Over Valve, Actuator Relay SystemBFS000EE
INSPECTION PROCEDURE
1. CHECK SELF-DIAGNOSTIC RESULTS
Check the self-diagnostic results.
Is above displayed on self-diagnosis display?
YES >> GO TO 2.
NO >> INSPECTION END
2. CHECK CONNECTOR
1. Turn ignition switch OFF, disconnect ABS actuator and electric unit (control unit) connector, and check ter-
minal for deformation, disconnection, looseness, and so on. If there is a malfunction, repair or replace ter-
minal.
2. Securely reconnect connectors and perform self-diagnosis again.
OK or NG
OK >> Connector terminal contact is loose, damaged, open or shorted.
NG >> GO TO 3.
3. CHECK SOLENOID, VDC CHANGE-OVER VALVE, ACTUATOR RELAY POWER SUPPLY
1. Turn ignition switch OFF and disconnect ABS actuator and elec-
tric unit (control unit) connectors.
2. Check voltage between ABS actuator and electric unit (control
unit) harness connector E241 terminal 16 and ground.
OK or NG
OK >> GO TO 4.
NG >> Circuit malfunction between battery and ABS actuator
and electric unit (control unit). Repair the circuit.
Self-diagnostic results
FR LH IN ABS SOL
FR LH OUT ABS SOL
FR RH IN ABS SOL
FR RH OUT ABS SOL
RR LH IN ABS SOL
RR LH OUT ABS SOL
RR RH IN ABS SOL
RR RH OUT ABS SOL
CV 1
CV 2
SV 1
SV 2
ACTUATOR RLY
ABS actuator and electric unit (contorl unit) Ground Voltage
16 —Battery voltage
(Approx. 12 V)
SFIA2102E

TROUBLE DIAGNOSIS FOR SYSTEM
BRC-77
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

4. CHECK SOLENOID, VDC CHANGE-OVER VALVE, ACTUATOR RELAY GROUND CIRCUIT

Check continuity between ABS actuator and electric unit (control
unit) harness connector E241 terminal 46 and ground.
OK or NG
OK >> Replace ABS actuator and electric unit (control unit).
NG >> Harness or connector is open or shorted. Repair or
replace malfunctioning components.
Stop Lamp Switch SystemBFS000EF
INSPECTION PROCEDURE
1. CHECK SELF-DIAGNOSTIC RESULTS
Check the self-diagnostic results.
Is above displayed on self-diagnosis display?
YES >> GO TO 2.
NO >> INSPECTION END
2. CHECK CONNECTOR
1. Turn ignition switch OFF, disconnect ABS actuator and electric unit (control unit) connector and stop lamp
switch connector, and check terminal for deformation, disconnection, looseness, and so on. If there is a
malfunction, repair or replace the terminal.
2. Securely reconnect connectors.
3. Start engine.
4. Repeat pumping brake pedal carefully several times, and then perform self-diagnosis again.
OK or NG
OK >> Connector terminal contact is loose, damaged, open or shorted.
NG >> GO TO 3.
ABS actuator and electric unit (contorl unit) Ground Continuity
46 — Yes
SFIA2103E
Self-diagnostic results
STOP LAMP SW

CVT-6
INDEX FOR DTC

INDEX FOR DTCPFP:00024
Alphabetical Index BCS001FM
NOTE:
If DTC “U1000 CAN COMM CIRCUIT” is displayed with other DTC s, first perform the trouble diagnosis
for “DTC U1000 CAN COMMUNICATION LINE”. Refer to CVT-53
.
Items
(CONSULT-II screen terms) DTC Reference page
A/T TCC S/V FNCTN P0744 CVT-94
ATF TEMP SEN/CIRC P0710CVT-69
BELT DAMGP0730CVT-87
BRAKE SW/CIRC P0703CVT-60
CAN COMM CIRCUIT U1000CVT-53
CVT SPD SEN/FNCTN P1723CVT-143
ENGINE SPEED SIG P0725CVT-85
ELEC TH CONTROL P1726CVT-145
ESTM VEH SPD SIG P1722CVT-141
INPUT SPD SEN/CIRC P0715CVT-74
L/PRESS CONTROL P1745CVT-152
L/PRESS SOL/CIRC P0745CVT-97
LU-SLCT SOL/CIRC P1740CVT-147
MANUAL MODE SWITCH P0826CVT-113
PNP SW/CIRCP0705CVT-62
PRESS SEN/FNCTN P0841CVT-123
PRS CNT SOL/A FCTN P0746CVT-102
PRS CNT SOL/B CIRC P0778CVT-108
PRS CNT SOL/B FCTN P0776CVT-105
SEC/PRESS DOWN P0868CVT-131
STARTER RELAY/CIRC P0615CVT-56
STEP MOTR CIRC P1777CVT-153
STEP MOTR/FNCTN P1778CVT-157
TCC SOLENOID/CIRC P0740CVT-89
TCM-POWER SUPPLY P1701CVT-134
TP SEN/CIRC A/T P1705CVT-139
TR PRS SENS/A CIRC P0840CVT-118
TR PRS SENS/B CIRC P0845CVT-126
VEH SPD SEN/CIR AT P0720CVT-79

INDEX FOR DTC
CVT-7
D
E
F
G
H
I
J
K
L
MA
B
CVT

DTC No. Index BCS001FN
NOTE:
If DTC “U1000 CAN COMM CIRCUIT” is displayed with other DTC s, first perform the trouble diagnosis
for “DTC U1000 CAN COMMUNICATION LINE”. Refer to CVT-53
.
DTCItems
(CONSULT-II screen terms)Reference page
P0615 STARTER RELAY/CIRCCVT-56
P0703 BRAKE SW/CIRCCVT-60
P0705 PNP SW/CIRCCVT-62
P0710 ATF TEMP SEN/CIRCCVT-69
P0715 INPUT SPD SEN/CIRCCVT-74
P0720 VEH SPD SEN/CIR ATCVT-79
P0725 ENGINE SPEED SIGCVT-85
P0730 BELT DAMGCVT-87
P0740 TCC SOLENOID/CIRCCVT-89
P0744 A/T TCC S/V FNCTNCVT-94
P0745 L/PRESS SOL/CIRCCVT-97
P0746 PRS CNT SOL/A FCTNCVT-102
P0776 PRS CNT SOL/B FCTNCVT-105
P0778 PRS CNT SOL/B CIRCCVT-108
P0826 MANUAL MODE SWITCHCVT-113
P0840 TR PRS SENS/A CIRCCVT-118
P0841 PRESS SEN/FNCTNCVT-123
P0845 TR PRS SENS/B CIRCCVT-126
P0868 SEC/PRESS DOWNCVT-131
P1701 TCM-POWER SUPPLYCVT-134
P1705 TP SEN/CIRC A/TCVT-139
P1722 ESTM VEH SPD SIGCVT-141
P1723 CVT SPD SEN/FNCTNCVT-143
P1726 ELEC TH CONTROLCVT-145
P1740 LU-SLCT SOL/CIRCCVT-147
P1745 L/PRESS CONTROLCVT-152
P1777 STEP MOTR CIRCCVT-153
P1778 STEP MOTR/FNCTNCVT-157
U1000 CAN COMM CIRCUITCVT-53