service NISSAN TEANA 2003 Service Manual

PRECAUTIONS
LT-5
C
D
E
F
G
H
I
J
L
MA
B
LT

PRECAUTIONS PFP:00011
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
BKS002B7
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
General Precautions for Service OperationsBKS002B8

Never work with wet hands.

Xenon headlamp includes high voltage generating part. Be sure
to disconnect battery negative cable (negative terminal) or
power fuse before removing, installing, or touching the xenon
headlamp (including lamp bulb).

Turn the lighting switch OFF before disconnecting and connect-
ing the connector.

When turning the xenon headlamp on and while it is illuminated,
never touch the harness, bulb, and socket of the headlamp.

When checking the headlamp on/off operation, check it on vehi-
cle and with the power connected to the vehicle-side connector.

Do not touch the headlamp bulb glass surface with bare hands or allow oil or grease to get on it. Do not
touch the headlamp bulb just after the headlamp is turned off, because it is very hot.

Install the xenon headlamp bulb socket correctly. If it is installed
improperly, high-voltage leak or corona discharge may occur
that can melt the bulb, connector, and housing. Do not illuminate
the xenon headlamp bulb out of the headlamp housing. Doing
so can cause fire and harm your eyes.

When the bulb has burned out, wrap it in a thick vinyl bag and
discard. Do not break the bulb.

Leaving the bulb removed from the headlamp housing for a long
period of time can deteriorate the performance of the lens and
reflector (dirt, clouding). Always prepare a new bulb and have it
on hand when replacing the bulb.

Do not use organic solvent (paint thinner or gasoline) to clean
lamps and to remove old sealant.
PKIC2345E
EL-3422D

LT-82
ACTIVE AFS

Terminals and Reference Values for AFS Control UnitBKS002F8
CONSULT-II Functions (ADAPTIVE LIGHT)BKS002F9
CONSULT-II can display each diagnostic item using the diagnostic test mode shown below.
CONSULT-II BASIC OPERATION
Refer to GI-34, "CONSULT-II Start Procedure" .
WORK SUPPORT
Display Item List
Notes on Steering Angle Sensor (Neutral Point) Adjustment

Be sure to adjust steering angle sensor to the neutral point before driving if any of the followings is
removed/installed or replaced: AFS control unit; Steering angle sensor; Steering system part, Suspension
system part.

Steering angle sensor neutral point adjustment should be performed by using CONSULT-II. (The adjust-
ment is not operative without CONSULT-II.)
Operation Procedure (with VDC)
Perform steering angle sensor neutral point adjustment only on VDC side. Never perform the adjustment on
ADAPTIVE LIGHT side as this may lead to VDC malfunctions. If the adjustment has been performed on AFS
side, readjust on VDC side. For steering angle sensor neutral point adjustment procedures on VDC side, refer
to BRC-40, "
Adjustment of Steering Angle Sensor Neutral Position" in “ON-VEHICLE SERVICE”.
Te r m i n a l
No.Wire
colorSignal nameMeasuring condition
Reference value
Ignition
switchOperation or condition
1 G Ignition switch (ON) ON — Battery voltage
2 L CAN-H — — —
3 Y Bending lamp (LH) ONShift the lever to any position other than P
and turn lighting switch on the 2nd position,
and then turn the steering to the left.ON Battery voltage
OFF Approx. 0 V
4 B Ground ON — Approx. 0 V
5 P CAN-L — — —
6LGBattery power supply
(bending lamp power
supply)OFF — Battery voltage
8 R Bending lamp (RH) ONShift the lever to any position other than P
and turn lighting switch on the 2nd position,
and then turn the steering to the right.ON Battery voltage
OFF Approx. 0 V
Diagnosis mode Description
WORK SUPPORT Adjusts the steering angle sensor.
SELF-DIAG RESULTS AFS control unit performs CAN communication diagnosis and self-diagnosis.
DATA MONITOR Displays AFS control unit input/output data in real time.
CAN DIAG SUPPORT MNTR Monitors communication status of CAN communication.
ACTIVE TEST AFS control unit operates bending lamp. Operation check can be performed.
ECU PART NUMBER Displays part number stored in AFS control unit.
Work item Description
ST ANG SEN ADJUSTMENT Adjusts the steering angle sensor to neutral point (straight-ahead position).

LU-1
ENGINE LUBRICATION SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION LU
A
LU

ENGINE LUBRICATION SYSTEM
QR
PRECAUTIONS .......................................................... 3
Precautions for Liquid Gasket .................................. 3
LIQUID GASKET APPLICATION PROCEDURE ..... 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
Commercial Service Tools ........................................ 4
LUBRICATION SYSTEM ............................................ 5
Lubrication Circuit .................................................... 5
System Chart ........................................................... 6
ENGINE OIL ............................................................... 7
Inspection ................................................................. 7
ENGINE OIL LEVEL ............................................. 7
ENGINE OIL APPEARANCE ................................ 7
ENGINE OIL LEAKAGE ........................................ 7
OIL PRESSURE CHECK ...................................... 7
Changing Engine Oil ................................................ 9
OIL FILTER ............................................................... 10
Removal and Installation ........................................ 10
REMOVAL ........................................................... 10
INSTALLATION ................................................... 10
INSPECTION AFTER INSTALLATION ............... 10
OIL PUMP ..................................................................11
Removal and Installation ......................................... 11
REMOVAL ............................................................ 11
INSTALLATION .................................................... 11
INSPECTION AFTER INSTALLATION ................ 11
Disassembly and Assembly .................................... 11
DISASSEMBLY .................................................... 11
INSPECTION AFTER DISASSEMBLY ............... 12
ASSEMBLY ......................................................... 13
SERVICE DATA AND SPECIFICATIONS (SDS) ...... 14
Standard and Limit ................................................. 14
OIL PRESSURE .................................................. 14
ENGINE OIL CAPACITY (APPROXIMATE) ........ 14
OIL PUMP ........................................................... 14
REGULATOR VALVE .......................................... 14
VQ
PRECAUTIONS ........................................................ 15
Precautions for Liquid Gasket ................................ 15
LIQUID GASKET APPLICATION PROCEDURE ... 15
PREPARATION ......................................................... 16
Special Service Tools ............................................. 16
Commercial Service Tools ...................................... 16
LUBRICATION SYSTEM .......................................... 17
Lubrication Circuit ................................................... 17
System Chart .......................................................... 18
ENGINE OIL .............................................................. 19
Inspection ............................................................... 19
ENGINE OIL LEVEL ............................................ 19
ENGINE OIL APPEARANCE .............................. 19
ENGINE OIL LEAKAGE ...................................... 19
OIL PRESSURE CHECK .................................... 20
Changing Engine Oil ............................................... 21
OIL FILTER ............................................................... 22
Removal and Installation ........................................ 22
REMOVAL ........................................................... 22
INSTALLATION ................................................... 22
INSPECTION AFTER INSTALLATION ................ 22
OIL COOLER (VQ35DE) ........................................... 23
Removal and Installation ........................................ 23
REMOVAL ........................................................... 23
INSPECTION AFTER REMOVAL ....................... 24
INSTALLATION ................................................... 24
INSPECTION AFTER INSTALLATION ................ 24
OIL PUMP ................................................................. 25
Removal and Installation ........................................ 25
REMOVAL ........................................................... 25
INSTALLATION ................................................... 25
INSPECTION AFTER INSTALLATION ................ 25
Disassembly and Assembly .................................... 25
DISASSEMBLY ................................................... 25
INSPECTION AFTER DISASSEMBLY ................ 26
ASSEMBLY ......................................................... 27

LU-2 SERVICE DATA AND SPECIFICATIONS (SDS) ...... 28
Standard and Limit .................................................. 28
OIL PRESSURE .................................................. 28
OIL CAPACITY (APPROXIMATE) ....................... 28
OIL PUMP ........................................................... 28
REGULATOR VALVE .......................................... 28

LU-4
[QR]
PREPARATION

PREPARATIONPFP:00002
Special Service ToolsBBS0059L
Commercial Service ToolsBBS0059M
Tool number
Tool nameDescription
ST25051001
Oil pressure gaugeMeasuring oil pressure
Maximum measuring range: 2,452 kPa
(24.52 bar, 25 kg/cm
2 , 356 psi)
ST25052000
HoseAdapting oil pressure gauge to cylinder block
KV10115801
Oil filter wrenchRemoving and installing oil filter
a: 64.3 mm (2.531 in)
WS39930000
Tube presserPressing the tube of liquid gasket
S-NT050
S-NT559
S-NT375
S-NT052
Tool nameDescription
Deep socketRemoving and installing oil pressure switch
a: 26 mm (1.02 in)
PBIC2072E

LU-14
[QR]
SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
Standard and LimitBBS0059U
OIL PRESSURE
*: Engine oil temperature at 80° (176°F)
ENGINE OIL CAPACITY (APPROXIMATE)
Unit: (Imp qt)
OIL PUMP
Unit: mm (in)
REGULATOR VALVE
Unit: mm (in) Engine speed
rpm Approximate discharge pressure*
kPa (bar, kg/cm
2 , psi)
Idle speed More than 98 (0.98, 1.0, 14)
2,000 More than 294 (2.94, 3.0, 43)
Drain and refillWith oil filter change 3.9 (3-3/8)
Without oil filter change 3.7 (3-1/4)
Dry engine (Overhaul)4.5 (4)
Oil pump body to outer rotor radial clearance 0.114 - 0.179 (0.0045 - 0.0070)
Inner rotor to outer rotor tip clearance Below 0.220 (0.0087)
Oil pump body to inner rotor side clearance 0.030 - 0.070 (0.0012 - 0.0028)
Oil pump body to outer rotor side clearance 0.060 - 0.110 (0.0024 - 0.0043)
Inner rotor to oil pump body clearance 0.035 - 0.070 (0.0014 - 0.0028)
Regulator valve to valve hole clearance 0.040 - 0.097 (0.0016 - 0.0038)

LU-16
[VQ]
PREPARATION

PREPARATIONPFP:00002
Special Service Tools BBS004WG
Commercial Service ToolsBBS004WH
Tool number
Tool nameDescription
ST25051001
Oil pressure gaugeMeasuring oil pressure
Maximum measuring range: 2,452 kPa
(24.52 bar, 25 kg/cm
2 , 356 psi)
ST25052000
HoseAdapting oil pressure gauge to oil pan (upper)
KV10115801
Oil filter wrenchRemoving and installing oil filter
a: 64.3 mm (2.531 in)
WS39930000
Tube presser Pressing the tube of liquid gasket
NT050
S-NT559
S-NT375
NT052
Tool nameDescription
Deep socketRemoving and installing oil pressure switch
Deep socket 27 mm (1.06 in)
PBIC4066E

LU-28
[VQ]
SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
Standard and LimitBBS004WQ
OIL PRESSURE
*: Engine oil temperature at 80°C (176°F)
OIL CAPACITY (APPROXIMATE)
Unit: (Imp qt)
OIL PUMP
Unit: mm (in)
REGULATOR VALVE
Unit: mm (in) Engine speed
rpm Approximate discharge pressure*
kPa (bar, kg/cm
2 , psi)
Idle speed More than 98 (0.98, 1.0, 14)
2,000 More than 294 (2.94, 3.0, 43)
Drain and refillWith oil filter change 4.0 (3-1/2)
Without oil filter change 3.7 (3-1/4)
Dry engine (Overhaul)5.0 (4-3/8)
Items VQ23DE VQ35DE
Oil pump body to oil pump outer rotor radial clearance 0.120 - 0.195 (0.0047 - 0.0077) 0.114 - 0.260 (0.0045 - 0.0102)
Oil pump inner rotor to oil pump outer rotor tip clearance 0.060 - 0.160 (0.0024 - 0.0063) Below 0.180 (0.0071)
Oil pump body to oil pump inner rotor side clearance 0.030 - 0.070 (0.0012 - 0.0028)
Oil pump body to oil pump outer rotor side clearance 0.050 - 0.090 (0.0020 - 0.0035) 0.050 - 0.110 (0.0020 - 0.0043)
Oil pump inner rotor to oil pump body clearance 0.045 - 0.091 (0.0018 - 0.0036)
Items VQ23DE VQ35DE
Regulator valve to oil pump body clearance 0.025 - 0.070 (0.0010 - 0.0028) 0.040 - 0.097 (0.0016 - 0.0038)

MA-1
MAINTENANCE
L MAINTENANCE
CONTENTS
C
D
E
F
G
H
I
J
K
M
SECTION MA
A
B
MA

MAINTENANCE
PREPARATION ........................................................... 3
Special Service Tools ............................................... 3
Commercial Service Tools ........................................ 3
DESCRIPTION ............................................................ 4
Pre-Delivery Inspection Items .................................. 4
GENERAL MAINTENANCE ....................................... 6
General Maintenance ............................................... 6
OUTSIDE THE VEHICLE ...................................... 6
INSIDE THE VEHICLE .......................................... 6
UNDER THE HOOD AND VEHICLE .................... 7
PERIODIC MAINTENANCE ....................................... 8
Periodic Maintenance ............................................... 8
ENGINE AND EMISSION CONTROL MAINTE-
NANCE .................................................................. 8
CHASSIS AND BODY MAINTENANCE ............... 9
MAINTENANCE UNDER SEVERE DRIVING
CONDITIONS ...................................................... 10
ENGINE AND EMISSION CONTROL MAINTE-
NANCE ................................................................. 11
CHASSIS AND BODY MAINTENANCE ............. 12
MAINTENANCE UNDER SEVERE DRIVING
CONDITIONS ...................................................... 13
RECOMMENDED FLUIDS AND LUBRICANTS ...... 14
Fluids and Lubricants ............................................. 14
SAE Viscosity Number ........................................... 15
GASOLINE ENGINE ........................................... 15
Anti-Freeze Coolant Mixture Ratio ......................... 15
ENGINE MAINTENANCE (QR20DE) ....................... 16
Checking Drive Belts .............................................. 16
Tension Adjustment ................................................ 16
Changing Engine Coolant ...................................... 16
DRAINING ENGINE COOLANT ......................... 16
REFILLING ENGINE COOLANT ........................ 17
FLUSHING COOLING SYSTEM ......................... 18
Checking Cooling System ...................................... 18
CHECKING COOLING SYSTEM HOSES .......... 19
CHECKING RADIATOR CAP .............................. 19
CHECKING RADIATOR SYSTEM FOR LEAKS ... 20
Checking Fuel Lines ............................................... 20
Changing Air Cleaner Filter .................................... 20VISCOUS PAPER TYPE ..................................... 20
Changing Engine Oil ............................................... 20
Changing Oil Filter .................................................. 21
REMOVAL ........................................................... 21
INSTALLATION ................................................... 22
INSPECTION AFTER INSTALLATION ................ 22
Checking and Changing Spark Plugs ..................... 22
REMOVAL ........................................................... 22
INSPECTION AFTER REMOVAL ....................... 23
INSTALLATION ................................................... 23
Checking EVAP Vapor Lines .................................. 23
ENGINE MAINTENANCE (VQ23DE AND VQ35DE) ... 24
Checking Drive Belts .............................................. 24
Tension Adjustment ................................................ 24
ALTERNATOR AND A/C COMPRESSOR BELT ... 25
POWER STEERING OIL PUMP BELT ................ 25
Changing Engine Coolant ....................................... 25
DRAINING ENGINE COOLANT .......................... 26
REFILLING ENGINE COOLANT ......................... 26
FLUSHING COOLING SYSTEM ......................... 27
Checking Cooling System ...................................... 28
CHECKING COOLING SYSTEM HOSES ........... 28
CHECKING RADIATOR CAP .............................. 28
CHECKING RADIATOR ...................................... 29
CHECKING COOLING SYSTEM FOR LEAKS ... 29
Checking Fuel Lines ............................................... 30
Changing Air Cleaner Filter .................................... 30
VISCOUS PAPER TYPE ..................................... 30
Changing Engine Oil ............................................... 30
Changing Oil Filter .................................................. 31
REMOVAL ........................................................... 31
INSTALLATION ................................................... 31
INSPECTION AFTER INSTALLATION ................ 32
Changing Spark Plug (Platinum-Tipped Type) ....... 32
REMOVAL ........................................................... 32
INSPECTION AFTER REMOVAL ....................... 32
INSTALLATION ................................................... 33
Checking Positive Crankcase Ventilation System ... 33
PCV (POSITIVE CRANKCASE VENTILATION)
VALVE ................................................................. 33

MA-2 PCV VALVE VENTILATION HOSE ...................... 34
Checking EVAP Vapor Lines .................................. 34
CHASSIS AND BODY MAINTENANCE ................... 35
Checking Exhaust System ...................................... 35
Checking A/T Fluid ................................................. 35
Changing A/T Fluid ................................................. 36
Checking CVT Fluid ................................................ 36
Changing CVT Fluid ............................................... 38
Balancing Wheels (Bonding Weight Type) ............. 38
REMOVAL ........................................................... 38
WHEEL BALANCE ADJUSTMENT ..................... 38
Tire Rotation ........................................................... 40
Checking Brake Fluid Level and Leaks .................. 40
Checking Brake Lines and Cables ......................... 40
Changing Brake Fluid ............................................. 40
Checking Disc Brake .............................................. 41
ROTOR ................................................................ 41
CALIPER ............................................................. 41
PAD ..................................................................... 41
Checking Steering Gear and Linkage ..................... 41
STEERING GEAR ............................................... 41
STEERING LINKAGE .......................................... 41
Checking Power Steering Fluid and Lines .............. 42
Axle and Suspension Parts ..................................... 42
Drive Shaft .............................................................. 43
Lubricating Locks, Hinges and Hood Latch ............ 43Checking Seat Belt, Buckles, Retractors, Anchors
and Adjusters .......................................................... 44
Checking Body Corrosion ....................................... 45
HEMMED PANELS .............................................. 45
PANEL JOINT ...................................................... 45
PANEL EDGE ...................................................... 45
PARTS CONTACT ............................................... 45
PROTECTORS .................................................... 45
ANTI-CORROSION MATERIALS ........................ 45
DRAIN HOLES ..................................................... 45
SERVICE DATA AND SPECIFICATIONS (SDS) ...... 46
Standard and Limit .................................................. 46
BELT DEFLECTION (QR20DE) ........................... 46
BELT DEFLECTION (VQ23DE AND VQ35DE) ... 46
ENGINE COOLANT CAPACITY (APPROXI-
MATE) (QR20DE) ................................................ 46
ENGINE COOLANT CAPACITY (APPROXI-
MATE) (VQ23DE AND VQ35DE) ......................... 46
RADIATOR ........................................................... 46
ENGINE OIL CAPACITY (APPROXIMATE)
(QR20DE) ............................................................ 46
ENGINE OIL CAPACITY (APPROXIMATE)
(VQ23DE AND VQ35DE) ..................................... 47
SPARK PLUG (PLATINUM-TIPPED TYPE)
(QR20DE, VQ23DE AND VQ35DE) .................... 47
WHEEL BALANCE .............................................. 47