Back lamp NISSAN TEANA 2003 Owner's Guide

LT-4 Wiring Diagram — STOP/L — ..............................190
WITH REAR SUNSHADE AND REAR VIEW
CAMERA ...........................................................190
WITHOUT REAR SUNSHADE AND REAR VIEW
CAMERA ...........................................................191
Bulb Replacement ................................................192
HIGH-MOUNTED STOP LAMP .........................192
STOP LAMP ......................................................192
Removal and Installation ......................................192
HIGH-MOUNTED STOP LAMP .........................192
STOP LAMP ......................................................192
BACK-UP LAMP .....................................................193
Wiring Diagram — BACK/L — ..............................193
WITH A/T ...........................................................193
WITH CVT .........................................................194
Bulb Replacement ................................................195
Removal and Installation ......................................195
PARKING, LICENSE PLATE AND TAIL LAMPS ....196
Component Parts and Harness Connector Location .196
System Description ...............................................196
OUTLINE ...........................................................196
PARKING, LICENCE PLATE AND TAIL LAMPS
OPERATION ......................................................197
COMBINATION SWITCH READING FUNCTION .197
EXTERIOR LAMP BATTERY SAVER CONTROL .197
CAN Communication System Description ............198
CAN Communication Unit .....................................198
Schematic .............................................................199
Wiring Diagram — TAIL/L — ................................200
Terminals and Reference Values for BCM ............205
Terminals and Reference Values for IPDM E/R ....206
How to Perform Trouble Diagnoses ......................206
Preliminary Check ................................................206
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ..................................................................206
CONSULT-II Functions (BCM) ..............................207
CONSULT-II Functions (IPDM E/R) ......................207
Parking, License Plate and Tail Lamps Do Not Illu-
minate ...................................................................208
Tail lamp Indicator Does Not Illuminate ................212
Parking, License Plate and Tail Lamps Do Not Go
OFF ......................................................................213
Bulb Replacement ................................................215
LICENSE PLATE LAMP ....................................215
PARKING LAMP ................................................215
TAIL LAMP ........................................................215
Removal and Installation ......................................215
LICENSE PLATE LAMP ....................................215
PARKING LAMP ................................................215
TAIL LAMP ........................................................215
REAR COMBINATION LAMP .................................216
Bulb Replacement ................................................216
REAR TURN SIGNAL LAMP BULB, BACK-UP
LAMP BULB AND STOP/TAIL LAMP BULB ......216
Removal and Installation ......................................216
REMOVAL .........................................................216
INSTALLATION ..................................................216
INTERIOR LAMP ....................................................217Wiring Diagram — INT/L — ..................................217
Bulb Replacement .................................................218
VANITY MIRROR LAMP ....................................218
INTERIOR ROOM LAMP ........................................219
Component Parts and Harness Connector Location .219
System Description ...............................................219
OUTLINE ...........................................................219
SWITCH OPERATION .......................................220
STEP LAMP OPERATION .................................221
TRUNK ROOM LAMP OPERATION ..................221
INTERIOR ROOM LAMP TIMER OPERATION .221
INTERIOR ROOM LAMP BATTERY SAVER
CONTROL .........................................................222
Schematic .............................................................223
Wiring Diagram — ROOM/L — .............................225
Terminals and Reference Values for BCM ............230
How to Perform With Trouble Diagnoses ..............231
Preliminary Check .................................................232
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ...................................................................232
CONSULT-II Functions (BCM) ..............................233
CONSULT-II BASIC OPERATION .....................233
WORK SUPPORT (INT LAMP) .........................233
DATA MONITOR (INT LAMP) ............................233
ACTIVE TEST ....................................................234
WORK SUPPORT (BATTERY SAVER) .............234
DATA MONITOR (BATTERY SAVER) ...............235
Interior Room Lamps Do Not Illuminate ................236
Interior Room Lamps Illuminate But Timer Does Not
Operate .................................................................240
Bulb Replacement .................................................241
MAP LAMP ........................................................241
STEP LAMP .......................................................241
PERSONAL LAMP .............................................241
TRUNK ROOM LAMP ........................................241
IGNITION KEYHOLE ILLUMINATION ...............242
Removal and Installation .......................................242
MAP LAMP ........................................................242
STEP LAMP .......................................................242
PERSONAL LAMP .............................................243
TRUNK ROOM LAMP ........................................243
ILLUMINATION ........................................................244
System Description ...............................................244
OUTLINE ...........................................................244
ILLUMINATION OPERATION BY LIGHTING
SWITCH .............................................................244
EXTERIOR LAMP BATTERY SAVER CONTROL .246
CAN Communication System Description ............246
CAN Communication Unit .....................................246
Schematic .............................................................247
Wiring Diagram — ILL — ......................................249
Bulb Replacement .................................................260
ASHTRAY ILLUMINATION ................................260
GLOVE BOX LAMP ...........................................260
CIGARETTE LIGHTER ILLUMINATION ............260
BULB SPECIFICATIONS ........................................261
Headlamp ..............................................................261
Exterior Lamp ........................................................261
Interior Lamp/Illumination ......................................261

HEADLAMP - XENON TYPE -
LT-9
C
D
E
F
G
H
I
J
L
MA
B
LT

XENON HEADLAMP
Xenon type headlamp is adapted to the low beam headlamps. Xenon bulbs do not use a filament. Instead,
they produce light when a high voltage current is passed between two tungsten electrodes through a mixture
of xenon (an inert gas) and certain other metal halides. In addition to added lighting power, electronic control
of the power supply gives the headlamps stable quality and tone color.
Following are some of the many advantages of the xenon type headlamp.

The light produced by the headlamps is a white color comparable to sunlight that is easy on the eyes.

Light output is nearly double that of halogen headlamps, affording increased area of illumination.

The light features a high relative spectral distribution at wavelengths to which the human eye is most sen-
sitive. This means that even in the rain, more light is reflected back from the road surface toward the vehi-
cle, for added visibility.

Power consumption is approximately 25 percent less than halogen headlamps, reducing battery load.
CAN Communication System DescriptionBKS001MW
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitBKS001MX
Refer to LAN-49, "CAN System Specification Chart" .

LT-20
HEADLAMP - XENON TYPE -

NOTE:
This item is displayed, but cannot be monitored.
ACTIVE TEST
Operation Procedure
1. Touch “HEAD LAMP” on “SELECT TEST ITEM” screen.
2. Touch “ACTIVE TEST” on “SELECT DIAG MODE” screen.
3. Touch item to be tested and check operation of the selected item.
4. During the operation check, touching “OFF” deactivates the operation.
Display Item List
NOTE:
This item is displayed, but cannot be monitored.
CONSULT-II Functions (IPDM E/R)BKS001N5
CONSULT-II can display each diagnostic item using the diagnostic test mode shown following.
CONSULT-II OPERATION
Refer to GI-34, "CONSULT-II Start Procedure" .
DOOR SW - DR “ON/OFF”Displays status of the driver door as judged from the driver door switch signal. (Door is open:
ON/door is closed: OFF)
DOOR SW - AS “ON/OFF”Displays status of the passenger door as judged from the passenger door switch signal. (Door
is open: ON/door is closed: OFF)
DOOR SW - RR “ON/OFF”Displays status of the rear door as judged from the rear door switch (RH) signal. (Door is open:
ON/door is closed: OFF)
DOOR SW - RL “ON/OFF”Displays status of the rear door as judged from the rear door switch (LH) signal. (Door is open:
ON/door is closed: OFF)
BACK DOOR SW
NOTE “OFF” —
TURN SIGNAL R “ON/OFF” Displays status (Turn right: ON/others: OFF) as judged from lighting switch signal.
TURN SIGNAL L “ON/OFF” Displays status (Turn left: ON/others: OFF) as judged from lighting switch signal.
OPTICAL SENSOR “0 - 5V ”Displays “outside brightness (close to 5V when light/close to 0V when dark)” judged from opti-
cal sensor signal.
VEHICLE SPEED “km/h” Displays vehicle speed as judged from vehicle speed signal.Monitor item Contents
CONSULT-II screen
displayTest item Description
TAIL LAMPParking, license plate and tail
lamps operationTail lamp relay is operated by switching operation ON-OFF.
HEAD LAMP High beam headlamp and low
beam headlamp operationHeadlamp high relay and headlamp low relay are operated by switching
operation (OFF: OFF, HI: high beam, LO: low beam).
RR FOG LAMP Rear fog lamp operation Rear fog lamp is operated by switching operation ON-OFF.
FR FOG LAMP Front fog lamp operation Front fog lamp relay is operated by switching operation ON-OFF.
CORNERING LAMP
Cornering lamp operation
NOTE—
ILL DIM SIGNALCombination meter and dis-
play dimming operationDimming function by MR output signal from BCM, it is operated by switch-
ing operation ON-OFF.
Diagnosis Mode Description
SELF-DIAGNOSTIC RESULTS Refer to PG-19, "
SELF-DIAG RESULTS" .
DATA MONITOR The input/output data of the IPDM E/R is displayed in real time.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
ACTIVE TEST IPDM E/R sends a drive signal to electronic components to check their operation.

ACTIVE AFS
LT-75
C
D
E
F
G
H
I
J
L
MA
B
LT

ACTIVE AFSPFP:253C0
Component Parts and Harness Connector LocationBKS002BW
System DescriptionBKS002BX
AFS (ADAPTIVE FRONT-LIGHTING SYSTEM)

Bending lamp (exclusive lamp for AFS) turn ON/OFF depending on the steering wheel angle and the vehi-
cle speed, when the headlamp LOW/HIGH lights, and the shift position is at any ranges except P.

Bending lamp supplies efficient light distribution for turning intersection and driving on the curves.

When turning to the left (right), bending lamp left (right) turn ON/OFF while driving forward or backward.
PKID0044E

BACK-UP LAMP
LT-193
C
D
E
F
G
H
I
J
L
MA
B
LT

BACK-UP LAMPPFP:26550
Wiring Diagram — BACK/L — BKS001QH
WITH A/T
TKWM4599E

LT-194
BACK-UP LAMP

WITH CVT
TKWM4600E

BACK-UP LAMP
LT-195
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementBKS001QI
Refer to LT- 2 1 6 , "Bulb Replacement" .
Removal and InstallationBKS0040G
Refer to LT- 2 1 6 , "Removal and Installation" .

LT-216
REAR COMBINATION LAMP

REAR COMBINATION LAMPPFP:26554
Bulb ReplacementBKS001R0
REAR TURN SIGNAL LAMP BULB, BACK-UP LAMP BULB AND STOP/TAIL LAMP BULB
1. Open trunk, and then remove trunk wheel house finisher. Refer to EI-58, "Removal and Installation for
Trunk Room Trim" .
2. Turn tail lamp bulb socket (1), rear turn signal lamp bulb socket
(2), back-up lamp bulb socket (3) (right side) and rear fog lamp
bulb socket (3) (left side) counterclockwise and unlock it.
3. Remove tail lamp bulb (4), rear turn signal lamp bulb (5), back-
up lamp bulb (6) (right side) and rear fog lamp bulb (6) (left
side).
Removal and InstallationBKS001R1
REMOVAL
1. Open trunk, and then remove trunk wheel house finisher. Refer to EI-58, "Removal and Installation for
Trunk Room Trim" .
2. Disconnect rear combination lamp connector.
3. Remove rear combination lamp mounting nuts (A).
4. Pull the rear combination lamp (1) toward rear of the vehicle and
remove clip (B) and locating pin (C) from the vehicle.
5. Remove seal packing (2) from rear combination lamp (1).
INSTALLATION
Installation is the reverse order of removal.
CAUTION:
Seal packing cannot be reused.Tail lamp : 12V - 5W
Rear turn signal lamp : 12V - 21W
Back-up lamp (Right side) : 12V - 21W
Rear fog lamp (Left side) : 12V - 21W
Stop lamp : LED
SKIB8646J
PKIC9679J
Rear combination lamp mounting nut : 5.1 N·m (0.52 kg-m, 45 in-lb)

INTERIOR ROOM LAMP
LT-241
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementBKS0040I
MAP LAMP
1. Remove lens using clip driver or suitable tool.
2. Remove bulb.
STEP LAMP
1. Remove front door step lamp. Refer to LT- 2 4 2 , "STEP LAMP" .
2. Remove bulb.
PERSONAL LAMP
1. Remove personal lamp. Refer to LT- 2 4 3 , "PERSONAL LAMP" .
2. Remove screw from back of personal lamp.
3. Insert a screwdriver or similar tool and remove lens.
4. Remove bulb.
TRUNK ROOM LAMP
Unfold pawl and remove lens, and remove bulb from bulb socket.Map lamp : 12V - 8W
SKIA8658E
Front door step lamp : 12V - 2.7W
SKIB0900E
Personal lamp : 12V - 8W
SKIA6359E
Trunk room lamp : 12V - 3.4W
SKIA6367E

BULB SPECIFICATIONS
LT-261
C
D
E
F
G
H
I
J
L
MA
B
LT

BULB SPECIFICATIONSPFP:26297
HeadlampBKS001RS
Exterior LampBKS001RT
Interior Lamp/IlluminationBKS001RU
Item Wattage (W)
Low/High (Xenon type)35 (D2S)
Low (Halogen type)55 (H11)
High (Halogen type)55 (H7)
Item Wattage (W)
Front combination lamp (Xenon type)Front turn signal lamp 21 (amber)
Parking lamp 5
Bending lamp 55 (H7)
Front combination lamp (Halogen type)Front turn signal lamp 21 (amber)
Parking lamp 5
Rear combination lampStop lamp LED
Tail lamp 5
Rear turn signal lamp 21
Back-up lamp 21
Rear fog lamp 21
Side turn signal lamp5
Front fog lamp35 (H8)
License plate lamp5
High-mounted stop lampLED
Item Wattage (W)
Map lamp8
Personal lamp8
Trunk room lamp3.4
Ashtray illumination1.4
Step lamp2.7
Vanity mirror lamp1.8
Ignition key hole illumination1.4
Glove box lamp1.4
Cigarette lighter illumination1.4