fuse box location NISSAN TEANA 2003 Service Manual

BL-32
POWER DOOR LOCK SYSTEM

BCM Power Supply and Ground CircuitBIS000W5
1. CHECK FUSE

Check 15A fuse [No.17, located in fuse block (J/B)]

Check 15A fuse [No.18, located in fuse block (J/B)] (With Intelligent Key)

Check 50A fusible link (letter M located in the fuse and fusible link box)
NOTE:
Refer to BL-21, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse, refer to PG-
3, "POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check voltage between BCM connector M4 terminals 42, 55 and
ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace BCM power supply circuit.
3. CHECK GROUND CIRCUIT
Check continuity between BCM connector M4 terminal 52 and
ground.
OK or NG
OK >> Power supply and ground circuit are OK.
NG >> Repair or replace BCM ground circuit.42 (Y/R) – Ground : Battery voltage
55 (W/B) – Ground : Battery voltage
PIIA6374E
52 (B) – Ground : Continuity should exist.
PIIA9131E

BL-46
REMOTE KEYLESS ENTRY SYSTEM

REMOTE KEYLESS ENTRY SYSTEMPFP:28596
Component Parts and Harness Connector LocationBIS000WE
System DescriptionBIS000WF
INPUTS
Power is supplied at all times

through 50A fusible link (letter M , located in the fuse and fusible link box)

to BCM terminal 55.

through 15A fuse [No. 17, located in the fuse block (J/B)]

to BCM terminal 42.
When the key switch is ON (key is inserted in ignition key cylinder), power is supplied

through 15A fuse [No. 17, located in the fuse block (J/B)]

through key switch terminals 1 and 4

to BCM terminal 37.
When the ignition switch is ACC or ON, power is supplied

through 10A fuse [No. 6, located in the fuse block (J/B)]

to BCM terminal 11.
When the ignition switch is ON or START, power is supplied

through 10A fuse [No. 1, located in the fuse block (J/B)]
1. BCM M3,M4,M5 2. Front door switch B10
(Driver side)3. Rear door switch (LH) B14
4. Key switch and key lock solenoid
connector M345. Trunk lid lock assembly T7
(Trunk room lamp switch)
PIIB8749E

BL-136
TRUNK LID OPENER

TRUNK LID OPENERPFP:84640
Component Parts and Harness Connector LocationBIS000Y6
System DescriptionBIS000Y7
Power is supplied at all times

through 50A fusible link (letter M, located in fuse and fusible link box)

to BCM terminal 55,

through 15A fuse [No.17, located in fuse block (J/B)]

to BCM terminal 42.
Ground is supplied

to BCM terminals 52

through body grounds M71 and M72.
When trunk lid opener switch is ON (pushed), ground is supplied

to BCM terminal 30

through trunk lid opener switch terminals 3 and 2, and

through body grounds M71 and M72.
And power is supplied

through BCM terminal 68

to trunk lid opener actuator terminal 2.
Ground is supplied

to trunk lid opener actuator terminal 1, and

through body grounds B214 and B217.
Then BCM unlocks trunk lid opener actuator.
TRUNK LID OPENER OPERATION
When trunk lid opener switch or trunk button of key fob is ON, trunk opener actuator unlocked by BCM.
BCM can unlock trunk lid opener actuator when

vehicle speed is less than 5 km/h (3MPH)
BCM does not unlock trunk lid opener actuator when

vehicle speed is more than 5 km/h (3MPH)
1. BCM M3,M4,M5 2. Trunk lid opener switch D9 3. Trunk lid lock assembly T7
(Trunk room lamp switch)
PIIB8753E

HOW TO USE THIS MANUAL
GI-17
C
D
E
F
G
H
I
J
K
L
MB
GI

Optional Splice
DESCRIPTION
SGI942
Num-
berItem Description
1 Power condition

This shows the condition when the system receives battery positive voltage (can be oper-
ated).
2 Fusible link

The double line shows that this is a fusible link.

The open circle shows current flow in, and the shaded circle shows current flow out.
3Fusible link/fuse loca-
tion

This shows the location of the fusible link or fuse in the fusible link or fuse box. For arrange-
ment, refer to PG section, POWER SUPPLY ROUTING.
4Fuse

The single line shows that this is a fuse.

The open circle shows current flow in, and the shaded circle shows current flow out.
5 Current rating

This shows the current rating of the fusible link or fuse.
6 Connectors

This shows that connector E3 is female and connector M1 is male.

The G/R wire is located in the 1A terminal of both connectors.

Terminal number with an alphabet (1A, 5B, etc.) indicates that the connector is SMJ connec-
tor. Refer to PG section, SMJ (SUPER MULTIPLE JUNCTION).
7 Optional splice

The open circle shows that the splice is optional depending on vehicle application.
8Splice

The shaded circle shows that the splice is always on the vehicle.
9 Page crossing

This arrow shows that the circuit continues to an adjacent page.

The A will match with the A on the preceding or next page.
10 Common connector

The dotted lines between terminals show that these terminals are part of the same connector.
11 Option abbreviation

This shows that the circuit is optional depending on vehicle application.
12 Relay

This shows an internal representation of the relay. For details, refer to PG section, STAN-
DARDIZED RELAY.
13 Connectors

This shows that the connector is connected to the body or a terminal with bolt or nut.

POWER WINDOW SYSTEM
GW-17
C
D
E
F
G
H
J
K
L
MA
B
GW

POWER WINDOW SYSTEMPFP:25401
Component Parts and Harness Connector LocationBIS000Z7
System DescriptionBIS000Z8
Power is supplied at all times

through 50A fusible link (letter M , located in the fuse and fusible link box), and

to BCM terminal 55.

through BCM terminal 54

to power window main switch terminal 19.

through 15A fuse [No. 17, located in the fuse block (J/B)].

to BCM terminal 42.
Ground is supplied at all times

to BCM terminal 52
PIIB0632E

GW-30
POWER WINDOW SYSTEM

Check BCM Power Supply and Ground Circuit BIS000ZF
1. CHECK FUSE

10A fuse [No.1, located in fuse block (J/B)]

15A fuse [No.17, located in fuse block (J/B)]

50A fusible link (letter M , located in the fuse and fusible link box)
NOTE:
Refer to GW-17, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown out, be sure to eliminate cause of malfunction before installing new fuse.
Refer toPG-3, "
POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
Check voltage between BCM connector and ground.
OK or NG
OK >> GO TO 3.
NG >> Check BCM power supply circuit for open or short.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM connector M4 terminal 52 and
ground.
OK or NG
OK >> BCM power supply and ground circuit are OK.
NG >> Check BCM ground circuit for open.
Check Power Window Main Switch Power Supply and Ground Circuit BIS000ZG
1. CHECK POWER SUPPLY CIRCUIT
Check voltage between power window main switch connector and
ground.
OK or NG
OK >> GO TO 2.
NG >> GO TO 3.
ConnectorTerminal (Wire color)
Condition of ignition
switchVoltage [V]
(Approx.)
(+) (-)
M338 (R)
GroundON
Battery voltage 42 (LG)
OFF
M4 55 (W/B)
PIIB1097E
52 (B) – Ground : Continuity should exist.
PIIB1099E
ConnectorTerminal (Wire color)
Condition of ignition
switchVoltage [V]
(Approx.)
(+) (-)
D6 10 (L/W)
GroundON
Battery voltage
D7 19 (R/Y) OFF
PIIB1144E

GW-54
REAR WINDOW DEFOGGER

REAR WINDOW DEFOGGERPFP:25350
Component Parts and Harness Connector LocationBIS000ZU
System DescriptionBIS000ZV
The rear window defogger is controlled by BCM and IPDM E/R.
The rear window defogger operates only for approximately 15 minutes.
Power is supplied at all times

through 20A fuse (No. 75, located in the IPDM E/R)

to rear window defogger relay terminal 3.

through 10A fuse (No. 32, located in the fuse and fusible link box)

to rear window defogger relay terminal 6.

through 50A fusible link (letter M , located in the fuse and fusible link box)

to BCM terminal 55.
PIIB2185E

GW-64
REAR WINDOW DEFOGGER

Check BCM Power Supply and Ground Circuit BIS00107
First perform the “SELF-DIAG RESULTS” in “BCM” with CONSULT-II, when perform the each trouble
diagnosis. Refer to BCS-14, "
CAN Communication Inspection Using CONSULT-II (Self-Diagnosis)" .
1. CHECK FUSE

10A fuse [No.1, located in fuse block (J/B)]

15A fuse [No.17, located in fuse block (J/B)]

50A fusible link (letter M, located in the fuse and fusible link box).
NOTE:
Refer to GW-54, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown out, be sure to eliminate cause of malfunction before installing new fuse. Refer to
PG-3, "
POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
Check voltage between BCM connector and ground.
OK or NG
OK >> GO TO 3.
NG >> Check BCM power supply circuit for open or short.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM connector M4 terminal 52 and
ground.
OK or NG
OK >> Power supply and ground circuit are OK.
NG >> Check BCM ground circuit for open.
ConnectorTerminal
Condition of ignition
switchVoltage [V]
(Approx.)
(+) (-)
M338 (R)
GroundON
Battery voltage 42 (LG)
OFF
M4 55 (W/B)
PIIB1097E
52 (B) – Ground : Continuity should exist.
PIIB1099E

IDX-4
ALPHABETICAL INDEX
Electric throttle control actuator (VQ23DE and VQ35DE)
EM-137
Electrical load signal circuit ................ EC-280, EC-670
Electrical unit ..................................................... PG-74
Electrical units location ...................................... PG-67
Electronic ignition (EI) system ............. EC-23, EC-360
EMNT - Wiring diagram ................................... EC-673
ENG SS - Wiring diagram ................................ AT-117
Engine control circuit diagram ............. EC-70, EC-413
Engine control component parts location .......... EC-64,
EC-406
Engine control module (ECM) ............ EC-190, EC-538
Engine control system diagram and chart ........ EC-20,
EC-357
Engine coolant temperature sensor (ECTS) ... EC-131,
EC-474
Engine coolant(QR20DE) ................................. CO-10
Engine coolant(VQ23DE and VQ35DE) ........... CO-34
Engine fail-safe system ........................ EC-59, EC-401
Engine mounting control (Front) ...................... EC-672
Engine oil filter replacement(QR20DE) ............. MA-21
Engine oil filter replacement(VQ23DE and VQ35DE) ...
MA-31
Engine oil precautions .......................................... GI-8
Engine oil replacement(QR20DE) .................... MA-20
Engine oil replacementVQ23DE and VQ35DE . MA-30
Engine oil(QR20DE) ............................................ LU-7
Engine oil(VQ23DE and VQ35DE) .................... LU-19
Engine removal(QR20DE) ................................ EM-77
Engine removal(VQ23DE and VQ35DE) ........ EM-223
Engine trouble diagnoses ................................ EC-394
ETC1 - Wiring diagram ...................... EC-201, EC-556
ETC2 - Wiring diagram ...................... EC-209, EC-564
ETC3 - Wiring diagram ...................... EC-214, EC-569
EVAP canister ...................................... EC-29, EC-369
EVAP canister purge volume control solenoid valve ....
EC-282
, EC-677
EVAP vapor lines inspection ............................. MA-23
EVAP vapor lines inspection(VQ23DE and VQ35DE) ..
MA-34
EVAP vapor lines inspectionVQ23DE and VQ35DE ....
MA-33
Evaporative emission (EVAP) system . EC-27, EC-366
Evaporator ..................................................... ATC-144
Exhaust manifold(QR20DE) ............................. EM-23
Exhaust manifold(VQ23DE and VQ35DE) ..... EM-140
Exhaust system ................................................... EX-2
Exhaust system inspection ..................... EX-2, MA-35
Expansion valve ............................................. ATC-145
F
F/FOG - Wiring diagram ................................... LT-129
F/LID - Wiring diagram ....................................... BL-45
F/PUMP - Wiring diagram .................. EC-296, EC-691
Floor trim ............................................................. EI-52
Flow charts ......................................................... GI-24
Fluid temparature sensor (CVT) ...................... CVT-69
Fluids ................................................................ MA-14
Fluorescent leak detector ............................. ATC-146
Fog lamp, front ................................................. LT-126
Freeze frame data .............................. EC-35, EC-376
FRO2 - Wiring diagram ..................... EC-302, EC-309
FRO2B1 - Wiring diagram ................ EC-697, EC-707
FRO2B2 - Wiring diagram ................ EC-699, EC-709
Front bumper ...................................................... EI-14
Front door ............................. BL-119, BL-123, GW-46
Front fog lamp .................................................. LT-126
Front passenger air bag .................................. SRS-39
Front seat belt ...................................................... SB-3
Front seat belt pre-tensioner ..... SB-2, SRS-3, SRS-46
Front side air bag ............................................ SRS-40
Front washer ...................................................... WW-4
Front wiper ......................................................... WW-4
FTS - Wiring diagram ...................................... CVT-70
Fuel cut control (at no load high engine speed) EC-24,
EC-361
Fuel gauge ............................................................ DI-4
Fuel injector and fuel tube(QR20DE) ................ EM-34
Fuel injector and fuel tube(VQ23DE and VQ35DE) ......
EM-155
Fuel lid opener, electric ...................................... BL-44
Fuel line inspection .............................................. FL-3
Fuel line inspection(QR20DE) .......................... MA-20
Fuel line inspectionVQ23DE and VQ35DE ....... MA-30
Fuel pressure check ........................... EC-49, EC-392
Fuel pressure release ......................... EC-49, EC-392
Fuel pump ......................................... EC-295, EC-690
Fuel pump and gauge .......................................... FL-4
Fuel system ......................................................... FL-3
Fuel tank .............................................................. FL-8
Fuel tank vacuum relief valve ............. EC-29, EC-369
Fuse .................................................................. PG-16
Fuse and fusible link box .................................. PG-80
Fusible link ........................................................ PG-16
G
Gauges ................................................................. DI-4
Glass ...................................... GW-11, GW-46, GW-50
Grease .............................................................. MA-14
Grille - See Exterior ............................................ EI-20
Ground distribution ........................................... PG-29
H
H/AIM - Wiring diagram ................................... LT-122
H/LAMP - Wiring diagram .................................. LT-42
Harness connector ............................................ PG-71
Harness layout .................................................. PG-42
Hazard warning lamp ....................................... LT-152
Headlamp aiming control ...................... LT-99, LT-122
Headlamp leveler - See Headlamp aiming control ........
LT-122
Headlining - See Roof trim .................................. EI-54
Heated oxygen sensor 1 ..... EC-143, EC-150, EC-301
Heated oxygen sensor 1 (bank 1) .... EC-486, EC-496,
EC-696

INSTRUMENT PANEL ASSEMBLY
IP-11
C
D
E
F
G
H
J
K
L
MA
B
IP

Removal and InstallationBIS00127
WORK ITEM TABLE
[ ]: The number shows the removal order.
NOTE:
*1: Assemble console box and cup holder. Refer to IP-19, "
CENTER CONSOLE" .
*2: Assemble damper and glove box illumination. Refer to IP-20, "
INSTRUMENT PASSENGER LOWER
PA N E L" .
1. Instrument panel pad 2. Instrument panel 3. Nut
4. Screw 5. Combination meter 6. Cluster lid A
7. Instrument center lower panel 8. Instrument panel finisher 9. Instrument panel pad A
10. instrument driver lower cover 11. Fuse block lid 12. Steering column upper cover
13. Steering column lower cover 14. Steering lock escutcheon 15. console rear cover
16. instrument panel lower cover (Lh) 17. Center console 18. Instrument panel stay cover
19. Console switch finisher 20. A/T console finisher 21. Instrument pane lower cover (RH)
22. Front ashtray 23. Glove box striker 24. Instrument passenger lower panel
25. Cluster lid C 26. Cluster lid D 27. Display unit
28. Instrument panel finisher D 29. Instrument panel pad B 30. Instrument passenger lower panel
Component Parts LocationReference
pageInstrument
panel & padCombination
meterDisplay unitCenter
console
A Kicking plate (LH/RH)EI-39
[ 1 ]
B Front pillar garnish (LH/RH)EI-39
[ 2 ]
C A/T selector lever knobAT- 2 1 3
[ 3 ] [ 1 ]
D A/T console finisherIP-12
[ 4 ] [ 2 ]
E Console switch finisherIP-12
[ 5 ] [ 3 ]
F Front ashtrayIP-12
[ 6 ] [ 4 ]
G Instrument panel lower cover (LH/RH)IP-13
[ 7 ] [ 5 ]
H Instrument panel stay coverIP-13
[ 8 ] [ 6 ]
I Console rear coverIP-13
[ 9 ] [ 7 ]
J Center console (*1)IP-14
[ 10 ] [ 8 ]
K Instrument passenger lower panel (*2)IP-14
[ 11 ]
L Instrument panel finisher (C/D)IP-14
[ 12 ] [ 1 ] C only [ 1 ]
M Cluster lid CIP-15
[ 13 ] [ 2 ]
N Cluster lid DIP-15
[ 14 ] [ 3 ]
O Display unitAV- 6 0
[ 15 ] [ 4 ]
P Fuse block lidIP-16
[ 16 ]
Q Instrument driver lower panelIP-16
[ 17 ]
R Steering lock escutcheonIP-16
[ 18 ] [ 2 ]
S Steering column upper/lower coverIP-16
[ 19 ] [ 3 ]
T Instrument panel pad AIP-16
[ 20 ] [ 4 ]
U Cluster lid AIP-17
[ 21 ] [ 5 ]
V Combination meterIP-17
[ 22 ] [ 6 ]
W Instrument panel pad BIP-17
[ 23 ]
X Instrument passenger upper panelIP-17
[ 24 ]
Y Instrument panel & padIP-17
[ 25 ]
Z Center instrument lower panelIP-18
[ 26 ]